// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause /* * Copyright (C) 2019 Marek Vasut */ #include #include "stm32mp15-u-boot.dtsi" #include "stm32mp15-ddr3-dhsom-2x1Gb-1066-binG.dtsi" #include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi" #include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi" / { aliases { i2c1 = &i2c2; i2c3 = &i2c4; i2c4 = &i2c5; mmc0 = &sdmmc1; mmc1 = &sdmmc2; spi0 = &qspi; usb0 = &usbotg_hs; eeprom0 = &eeprom0; }; config { u-boot,boot-led = "heartbeat"; u-boot,error-led = "error"; dh,som-coding-gpios = <&gpiof 12 0>, <&gpiof 13 0>, <&gpiof 15 0>; dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>; }; }; ðernet0 { phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>; /delete-property/ st,eth-ref-clk-sel; }; ðernet0_rmii_pins_a { pins1 { pinmux = , /* ETH1_RMII_TXD0 */ , /* ETH1_RMII_TXD1 */ , /* ETH1_RMII_TX_EN */ , /* ETH1_RMII_REF_CLK */ , /* ETH1_MDIO */ ; /* ETH1_MDC */ }; }; &i2c4 { bootph-all; bootph-pre-ram; eeprom0: eeprom@50 { }; }; &i2c4_pins_a { bootph-all; pins { bootph-all; }; }; &phy0 { /delete-property/ reset-gpios; }; &pinctrl { mco2_pins_a: mco2-0 { pins { pinmux = ; /* MCO2 */ bias-disable; drive-push-pull; slew-rate = <2>; }; }; mco2_sleep_pins_a: mco2-sleep-0 { pins { pinmux = ; /* MCO2 */ }; }; }; &pmic { bootph-all; bootph-pre-ram; regulators { bootph-pre-ram; }; }; &flash0 { bootph-pre-ram; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "fsbl1"; reg = <0x00000000 0x00040000>; }; partition@40000 { label = "fsbl2"; reg = <0x00040000 0x00040000>; }; partition@500000 { label = "uboot"; reg = <0x00080000 0x00160000>; }; partition@900000 { label = "env1"; reg = <0x001E0000 0x00010000>; }; partition@980000 { label = "env2"; reg = <0x001F0000 0x00010000>; }; }; }; &qspi { bootph-pre-ram; }; &qspi_clk_pins_a { bootph-pre-ram; pins { bootph-pre-ram; }; }; &qspi_bk1_pins_a { bootph-pre-ram; pins { bootph-pre-ram; }; }; &qspi_cs1_pins_a { bootph-pre-ram; pins { bootph-pre-ram; }; }; &rcc { /* * Reinstate clock names from stm32mp151.dtsi, the MCO2 trick * used in stm32mp15xx-dhcom-som.dtsi is not supported by the * U-Boot clock framework. */ clock-names = "hse", "hsi", "csi", "lse", "lsi"; clocks = <&clk_hse>, <&clk_hsi>, <&clk_csi>, <&clk_lse>, <&clk_lsi>; /* The MCO2 is already configured correctly, remove those. */ /delete-property/ assigned-clocks; /delete-property/ assigned-clock-parents; /delete-property/ assigned-clock-rates; st,clksrc = < CLK_MPU_PLL1P CLK_AXI_PLL2P CLK_MCU_PLL3P CLK_PLL12_HSE CLK_PLL3_HSE CLK_PLL4_HSE CLK_RTC_LSE CLK_MCO1_DISABLED CLK_MCO2_PLL4P >; st,clkdiv = < 1 /*MPU*/ 0 /*AXI*/ 0 /*MCU*/ 1 /*APB1*/ 1 /*APB2*/ 1 /*APB3*/ 1 /*APB4*/ 2 /*APB5*/ 23 /*RTC*/ 0 /*MCO1*/ 1 /*MCO2*/ >; st,pkcs = < CLK_CKPER_HSE CLK_FMC_ACLK CLK_QSPI_ACLK CLK_ETH_PLL4P CLK_SDMMC12_PLL4P CLK_DSI_DSIPLL CLK_STGEN_HSE CLK_USBPHY_HSE CLK_SPI2S1_PLL3Q CLK_SPI2S23_PLL3Q CLK_SPI45_HSI CLK_SPI6_HSI CLK_I2C46_HSI CLK_SDMMC3_PLL4P CLK_USBO_USBPHY CLK_ADC_CKPER CLK_CEC_LSE CLK_I2C12_HSI CLK_I2C35_HSI CLK_UART1_HSI CLK_UART24_HSI CLK_UART35_HSI CLK_UART6_HSI CLK_UART78_HSI CLK_SPDIF_PLL4P CLK_FDCAN_PLL4R CLK_SAI1_PLL3Q CLK_SAI2_PLL3Q CLK_SAI3_PLL3Q CLK_SAI4_PLL3Q CLK_RNG1_LSI CLK_RNG2_LSI CLK_LPTIM1_PCLK1 CLK_LPTIM23_PCLK3 CLK_LPTIM45_LSE >; /* * cfg = < DIVM1 DIVN P Q R PQR(p,q,r) >; * frac = < f >; * * PRQ(p,q,r) ... for p,q,r: 0-output disabled / 1-output enabled * DIVN ... actually multiplier, but RCC_PLL1CFGR1 calls the field DIVN * m ... for PLL1,2: m=2 ; for PLL3,4: m=1 * XTAL = 24 MHz * * VCO = ( XTAL / (DIVM1 + 1) ) * m * ( DIVN + 1 + ( f / 8192 ) ) * P = VCO / (P + 1) * Q = VCO / (Q + 1) * R = VCO / (R + 1) */ /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */ pll2: st,pll@1 { compatible = "st,stm32mp1-pll"; reg = <1>; cfg = < 2 65 1 0 0 PQR(1,1,1) >; frac = < 0x1400 >; bootph-all; }; /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */ pll3: st,pll@2 { compatible = "st,stm32mp1-pll"; reg = <2>; cfg = < 1 33 1 16 36 PQR(1,1,1) >; frac = < 0x1a04 >; bootph-all; }; /* VCO = 600.0 MHz => P = 100, Q = 50, R = 50 */ pll4: st,pll@3 { compatible = "st,stm32mp1-pll"; reg = <3>; cfg = < 1 49 5 11 11 PQR(1,1,1) >; bootph-all; }; }; &sdmmc1 { bootph-pre-ram; st,use-ckin; st,cmd-gpios = <&gpiod 2 0>; st,ck-gpios = <&gpioc 12 0>; st,ckin-gpios = <&gpioe 4 0>; }; &sdmmc1_b4_pins_a { bootph-pre-ram; pins1 { bootph-pre-ram; }; pins2 { bootph-pre-ram; }; }; &sdmmc1_dir_pins_a { bootph-pre-ram; pins1 { bootph-pre-ram; }; pins2 { bootph-pre-ram; }; }; &sdmmc2 { bootph-pre-ram; }; &sdmmc2_b4_pins_a { bootph-pre-ram; pins { bootph-pre-ram; }; }; &sdmmc2_d47_pins_a { bootph-pre-ram; pins { bootph-pre-ram; }; }; &uart4 { bootph-all; }; &uart4_pins_a { bootph-all; pins1 { bootph-all; }; pins2 { bootph-all; /* pull-up on rx to avoid floating level */ bias-pull-up; }; }; ®11 { bootph-pre-ram; }; ®18 { bootph-pre-ram; }; &usb33 { bootph-pre-ram; }; &usbotg_hs_pins_a { bootph-pre-ram; }; &usbotg_hs { bootph-pre-ram; }; &usbphyc { bootph-pre-ram; }; &usbphyc_port0 { bootph-pre-ram; }; &usbphyc_port1 { bootph-pre-ram; }; &vdd_usb { bootph-pre-ram; };