// SPDX-License-Identifier: GPL-2.0 /* * Copyright (C) Marvell International Ltd. and its affiliates */ #include #include #include #include #include #include #include #include "ddr3_init.h" #include "ddr3_hw_training.h" #include "xor.h" #ifdef MV88F78X60 #include "ddr3_patterns_64bit.h" #else #include "ddr3_patterns_16bit.h" #if defined(MV88F672X) #include "ddr3_patterns_16bit.h" #endif #endif /* * Debug */ #define DEBUG_MAIN_C(s, d, l) \ DEBUG_MAIN_S(s); DEBUG_MAIN_D(d, l); DEBUG_MAIN_S("\n") #define DEBUG_MAIN_FULL_C(s, d, l) \ DEBUG_MAIN_FULL_S(s); DEBUG_MAIN_FULL_D(d, l); DEBUG_MAIN_FULL_S("\n") #ifdef MV_DEBUG_MAIN #define DEBUG_MAIN_S(s) puts(s) #define DEBUG_MAIN_D(d, l) printf("%x", d) #else #define DEBUG_MAIN_S(s) #define DEBUG_MAIN_D(d, l) #endif #ifdef MV_DEBUG_MAIN_FULL #define DEBUG_MAIN_FULL_S(s) puts(s) #define DEBUG_MAIN_FULL_D(d, l) printf("%x", d) #else #define DEBUG_MAIN_FULL_S(s) #define DEBUG_MAIN_FULL_D(d, l) #endif #ifdef MV_DEBUG_SUSPEND_RESUME #define DEBUG_SUSPEND_RESUME_S(s) puts(s) #define DEBUG_SUSPEND_RESUME_D(d, l) printf("%x", d) #else #define DEBUG_SUSPEND_RESUME_S(s) #define DEBUG_SUSPEND_RESUME_D(d, l) #endif static u32 ddr3_sw_wl_rl_debug; static u32 ddr3_run_pbs = 1; void ddr3_print_version(void) { puts("DDR3 Training Sequence - Ver 5.7."); } void ddr3_set_sw_wl_rl_debug(u32 val) { ddr3_sw_wl_rl_debug = val; } void ddr3_set_pbs(u32 val) { ddr3_run_pbs = val; } int ddr3_hw_training(u32 target_freq, u32 ddr_width, int xor_bypass, u32 scrub_offs, u32 scrub_size, int dqs_clk_aligned, int debug_mode, int reg_dimm_skip_wl) { /* A370 has no PBS mechanism */ __maybe_unused u32 first_loop_flag = 0; u32 freq, reg; MV_DRAM_INFO dram_info; int ratio_2to1 = 0; int tmp_ratio = 1; int status; if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 1\n"); memset(&dram_info, 0, sizeof(dram_info)); dram_info.num_cs = ddr3_get_cs_num_from_reg(); dram_info.cs_ena = ddr3_get_cs_ena_from_reg(); dram_info.target_frequency = target_freq; dram_info.ddr_width = ddr_width; dram_info.num_of_std_pups = ddr_width / PUP_SIZE; dram_info.rl400_bug = 0; dram_info.multi_cs_mr_support = 0; #ifdef MV88F67XX dram_info.rl400_bug = 1; #endif /* Ignore ECC errors - if ECC is enabled */ reg = reg_read(REG_SDRAM_CONFIG_ADDR); if (reg & (1 << REG_SDRAM_CONFIG_ECC_OFFS)) { dram_info.ecc_ena = 1; reg |= (1 << REG_SDRAM_CONFIG_IERR_OFFS); reg_write(REG_SDRAM_CONFIG_ADDR, reg); } else { dram_info.ecc_ena = 0; } reg = reg_read(REG_SDRAM_CONFIG_ADDR); if (reg & (1 << REG_SDRAM_CONFIG_REGDIMM_OFFS)) dram_info.reg_dimm = 1; else dram_info.reg_dimm = 0; dram_info.num_of_total_pups = ddr_width / PUP_SIZE + dram_info.ecc_ena; /* Get target 2T value */ reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); dram_info.mode_2t = (reg >> REG_DUNIT_CTRL_LOW_2T_OFFS) & REG_DUNIT_CTRL_LOW_2T_MASK; /* Get target CL value */ #ifdef MV88F67XX reg = reg_read(REG_DDR3_MR0_ADDR) >> 2; #else reg = reg_read(REG_DDR3_MR0_CS_ADDR) >> 2; #endif reg = (((reg >> 1) & 0xE) | (reg & 0x1)) & 0xF; dram_info.cl = ddr3_valid_cl_to_cl(reg); /* Get target CWL value */ #ifdef MV88F67XX reg = reg_read(REG_DDR3_MR2_ADDR) >> REG_DDR3_MR2_CWL_OFFS; #else reg = reg_read(REG_DDR3_MR2_CS_ADDR) >> REG_DDR3_MR2_CWL_OFFS; #endif reg &= REG_DDR3_MR2_CWL_MASK; dram_info.cwl = reg; #if !defined(MV88F67XX) /* A370 has no PBS mechanism */ #if defined(MV88F78X60) if ((dram_info.target_frequency > DDR_400) && (ddr3_run_pbs)) first_loop_flag = 1; #else /* first_loop_flag = 1; skip mid freq at ALP/A375 */ if ((dram_info.target_frequency > DDR_400) && (ddr3_run_pbs) && (mv_ctrl_revision_get() >= UMC_A0)) first_loop_flag = 1; else first_loop_flag = 0; #endif #endif freq = dram_info.target_frequency; /* Set ODT to always on */ ddr3_odt_activate(1); /* Init XOR */ mv_sys_xor_init(&dram_info); /* Get DRAM/HCLK ratio */ if (reg_read(REG_DDR_IO_ADDR) & (1 << REG_DDR_IO_CLK_RATIO_OFFS)) ratio_2to1 = 1; /* * Xor Bypass - ECC support in AXP is currently available for 1:1 * modes frequency modes. * Not all frequency modes support the ddr3 training sequence * (Only 1200/300). * Xor Bypass allows using the Xor initializations and scrubbing * inside the ddr3 training sequence without running the training * itself. */ if (xor_bypass == 0) { if (ddr3_run_pbs) { DEBUG_MAIN_S("DDR3 Training Sequence - Run with PBS.\n"); } else { DEBUG_MAIN_S("DDR3 Training Sequence - Run without PBS.\n"); } if (dram_info.target_frequency > DFS_MARGIN) { tmp_ratio = 0; freq = DDR_100; if (dram_info.reg_dimm == 1) freq = DDR_300; if (MV_OK != ddr3_dfs_high_2_low(freq, &dram_info)) { /* Set low - 100Mhz DDR Frequency by HW */ DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Dfs High2Low)\n"); return MV_DDR3_TRAINING_ERR_DFS_H2L; } if ((dram_info.reg_dimm == 1) && (reg_dimm_skip_wl == 0)) { if (MV_OK != ddr3_write_leveling_hw_reg_dimm(freq, &dram_info)) DEBUG_MAIN_S("DDR3 Training Sequence - Registered DIMM Low WL - SKIP\n"); } if (ddr3_get_log_level() >= MV_LOG_LEVEL_1) ddr3_print_freq(freq); if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 2\n"); } else { if (!dqs_clk_aligned) { #ifdef MV88F67XX /* * If running training sequence without DFS, * we must run Write leveling before writing * the patterns */ /* * ODT - Multi CS system use SW WL, * Single CS System use HW WL */ if (dram_info.cs_ena > 1) { if (MV_OK != ddr3_write_leveling_sw( freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Sw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_SW; } } else { if (MV_OK != ddr3_write_leveling_hw(freq, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } #else if (MV_OK != ddr3_write_leveling_hw( freq, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hw)\n"); if (ddr3_sw_wl_rl_debug) { if (MV_OK != ddr3_write_leveling_sw( freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Sw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_SW; } } else { return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } #endif } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 3\n"); } if (MV_OK != ddr3_load_patterns(&dram_info, 0)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Loading Patterns)\n"); return MV_DDR3_TRAINING_ERR_LOAD_PATTERNS; } /* * TODO: * The mainline U-Boot port of the bin_hdr DDR training code * needs a delay of minimum 20ms here (10ms is a bit too short * and the CPU hangs). The bin_hdr code doesn't have this delay. * To be save here, lets add a delay of 50ms here. * * Tested on the Marvell DB-MV784MP-GP board */ mdelay(50); do { freq = dram_info.target_frequency; tmp_ratio = ratio_2to1; DEBUG_MAIN_FULL_S("DDR3 Training Sequence - DEBUG - 4\n"); #if defined(MV88F78X60) /* * There is a difference on the DFS frequency at the * first iteration of this loop */ if (first_loop_flag) { freq = DDR_400; tmp_ratio = 0; } #endif if (MV_OK != ddr3_dfs_low_2_high(freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Dfs Low2High)\n"); return MV_DDR3_TRAINING_ERR_DFS_H2L; } if (ddr3_get_log_level() >= MV_LOG_LEVEL_1) { ddr3_print_freq(freq); } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 5\n"); /* Write leveling */ if (!dqs_clk_aligned) { #ifdef MV88F67XX /* * ODT - Multi CS system that not support Multi * CS MRS commands must use SW WL */ if (dram_info.cs_ena > 1) { if (MV_OK != ddr3_write_leveling_sw( freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Sw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_SW; } } else { if (MV_OK != ddr3_write_leveling_hw( freq, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } #else if ((dram_info.reg_dimm == 1) && (freq == DDR_400)) { if (reg_dimm_skip_wl == 0) { if (MV_OK != ddr3_write_leveling_hw_reg_dimm( freq, &dram_info)) DEBUG_MAIN_S("DDR3 Training Sequence - Registered DIMM WL - SKIP\n"); } } else { if (MV_OK != ddr3_write_leveling_hw( freq, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hw)\n"); if (ddr3_sw_wl_rl_debug) { if (MV_OK != ddr3_write_leveling_sw( freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Sw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_SW; } } else { return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } } #endif if (debug_mode) DEBUG_MAIN_S ("DDR3 Training Sequence - DEBUG - 6\n"); } /* Read Leveling */ /* * Armada 370 - Support for HCLK @ 400MHZ - must use * SW read leveling */ if (freq == DDR_400 && dram_info.rl400_bug) { status = ddr3_read_leveling_sw(freq, tmp_ratio, &dram_info); if (MV_OK != status) { DEBUG_MAIN_S ("DDR3 Training Sequence - FAILED (Read Leveling Sw)\n"); return status; } } else { if (MV_OK != ddr3_read_leveling_hw( freq, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Read Leveling Hw)\n"); if (ddr3_sw_wl_rl_debug) { if (MV_OK != ddr3_read_leveling_sw( freq, tmp_ratio, &dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Read Leveling Sw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_SW; } } else { return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 7\n"); if (MV_OK != ddr3_wl_supplement(&dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hi-Freq Sup)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_HI_FREQ; } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 8\n"); #if !defined(MV88F67XX) /* A370 has no PBS mechanism */ #if defined(MV88F78X60) || defined(MV88F672X) if (first_loop_flag == 1) { first_loop_flag = 0; status = MV_OK; status = ddr3_pbs_rx(&dram_info); if (MV_OK != status) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (PBS RX)\n"); return status; } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 9\n"); status = ddr3_pbs_tx(&dram_info); if (MV_OK != status) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (PBS TX)\n"); return status; } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 10\n"); } #endif #endif } while (freq != dram_info.target_frequency); status = ddr3_dqs_centralization_rx(&dram_info); if (MV_OK != status) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (DQS Centralization RX)\n"); return status; } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 11\n"); status = ddr3_dqs_centralization_tx(&dram_info); if (MV_OK != status) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (DQS Centralization TX)\n"); return status; } if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 12\n"); } ddr3_set_performance_params(&dram_info); if (dram_info.ecc_ena) { /* Need to SCRUB the DRAM memory area to load U-Boot */ mv_sys_xor_finish(); dram_info.num_cs = 1; dram_info.cs_ena = 1; mv_sys_xor_init(&dram_info); mv_xor_mem_init(0, scrub_offs, scrub_size, 0xdeadbeef, 0xdeadbeef); /* Wait for previous transfer completion */ while (mv_xor_state_get(0) != MV_IDLE) ; if (debug_mode) DEBUG_MAIN_S("DDR3 Training Sequence - DEBUG - 13\n"); } /* Return XOR State */ mv_sys_xor_finish(); #if defined(MV88F78X60) /* Save training results in memeory for resume state */ ddr3_save_training(&dram_info); #endif /* Clear ODT always on */ ddr3_odt_activate(0); /* Configure Dynamic read ODT */ ddr3_odt_read_dynamic_config(&dram_info); return MV_OK; } void ddr3_set_performance_params(MV_DRAM_INFO *dram_info) { u32 twr2wr, trd2rd, trd2wr_wr2rd; u32 tmp1, tmp2, reg; DEBUG_MAIN_FULL_C("Max WL Phase: ", dram_info->wl_max_phase, 2); DEBUG_MAIN_FULL_C("Min WL Phase: ", dram_info->wl_min_phase, 2); DEBUG_MAIN_FULL_C("Max RL Phase: ", dram_info->rl_max_phase, 2); DEBUG_MAIN_FULL_C("Min RL Phase: ", dram_info->rl_min_phase, 2); if (dram_info->wl_max_phase < 2) twr2wr = 0x2; else twr2wr = 0x3; trd2rd = 0x1 + (dram_info->rl_max_phase + 1) / 2 + (dram_info->rl_max_phase + 1) % 2; tmp1 = (dram_info->rl_max_phase - dram_info->wl_min_phase) / 2 + (((dram_info->rl_max_phase - dram_info->wl_min_phase) % 2) > 0 ? 1 : 0); tmp2 = (dram_info->wl_max_phase - dram_info->rl_min_phase) / 2 + ((dram_info->wl_max_phase - dram_info->rl_min_phase) % 2 > 0 ? 1 : 0); trd2wr_wr2rd = (tmp1 >= tmp2) ? tmp1 : tmp2; trd2wr_wr2rd += 2; trd2rd += 2; twr2wr += 2; DEBUG_MAIN_FULL_C("WR 2 WR: ", twr2wr, 2); DEBUG_MAIN_FULL_C("RD 2 RD: ", trd2rd, 2); DEBUG_MAIN_FULL_C("RD 2 WR / WR 2 RD: ", trd2wr_wr2rd, 2); reg = reg_read(REG_SDRAM_TIMING_HIGH_ADDR); reg &= ~(REG_SDRAM_TIMING_H_W2W_MASK << REG_SDRAM_TIMING_H_W2W_OFFS); reg |= ((twr2wr & REG_SDRAM_TIMING_H_W2W_MASK) << REG_SDRAM_TIMING_H_W2W_OFFS); reg &= ~(REG_SDRAM_TIMING_H_R2R_MASK << REG_SDRAM_TIMING_H_R2R_OFFS); reg &= ~(REG_SDRAM_TIMING_H_R2R_H_MASK << REG_SDRAM_TIMING_H_R2R_H_OFFS); reg |= ((trd2rd & REG_SDRAM_TIMING_H_R2R_MASK) << REG_SDRAM_TIMING_H_R2R_OFFS); reg |= (((trd2rd >> 2) & REG_SDRAM_TIMING_H_R2R_H_MASK) << REG_SDRAM_TIMING_H_R2R_H_OFFS); reg &= ~(REG_SDRAM_TIMING_H_R2W_W2R_MASK << REG_SDRAM_TIMING_H_R2W_W2R_OFFS); reg &= ~(REG_SDRAM_TIMING_H_R2W_W2R_H_MASK << REG_SDRAM_TIMING_H_R2W_W2R_H_OFFS); reg |= ((trd2wr_wr2rd & REG_SDRAM_TIMING_H_R2W_W2R_MASK) << REG_SDRAM_TIMING_H_R2W_W2R_OFFS); reg |= (((trd2wr_wr2rd >> 2) & REG_SDRAM_TIMING_H_R2W_W2R_H_MASK) << REG_SDRAM_TIMING_H_R2W_W2R_H_OFFS); reg_write(REG_SDRAM_TIMING_HIGH_ADDR, reg); } /* * Perform DDR3 PUP Indirect Write */ void ddr3_write_pup_reg(u32 mode, u32 cs, u32 pup, u32 phase, u32 delay) { u32 reg = 0; if (pup == PUP_BC) reg |= (1 << REG_PHY_BC_OFFS); else reg |= (pup << REG_PHY_PUP_OFFS); reg |= ((0x4 * cs + mode) << REG_PHY_CS_OFFS); reg |= (phase << REG_PHY_PHASE_OFFS) | delay; if (mode == PUP_WL_MODE) reg |= ((INIT_WL_DELAY + delay) << REG_PHY_DQS_REF_DLY_OFFS); reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ reg |= REG_PHY_REGISTRY_FILE_ACCESS_OP_WR; reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ do { reg = reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR) & REG_PHY_REGISTRY_FILE_ACCESS_OP_DONE; } while (reg); /* Wait for '0' to mark the end of the transaction */ /* If read Leveling mode - need to write to register 3 separetly */ if (mode == PUP_RL_MODE) { reg = 0; if (pup == PUP_BC) reg |= (1 << REG_PHY_BC_OFFS); else reg |= (pup << REG_PHY_PUP_OFFS); reg |= ((0x4 * cs + mode + 1) << REG_PHY_CS_OFFS); reg |= (INIT_RL_DELAY); reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ reg |= REG_PHY_REGISTRY_FILE_ACCESS_OP_WR; reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ do { reg = reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR) & REG_PHY_REGISTRY_FILE_ACCESS_OP_DONE; } while (reg); } } /* * Perform DDR3 PUP Indirect Read */ u32 ddr3_read_pup_reg(u32 mode, u32 cs, u32 pup) { u32 reg; reg = (pup << REG_PHY_PUP_OFFS) | ((0x4 * cs + mode) << REG_PHY_CS_OFFS); reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ reg |= REG_PHY_REGISTRY_FILE_ACCESS_OP_RD; reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, reg); /* 0x16A0 */ do { reg = reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR) & REG_PHY_REGISTRY_FILE_ACCESS_OP_DONE; } while (reg); /* Wait for '0' to mark the end of the transaction */ return reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR); /* 0x16A0 */ } /* * Set training patterns */ int ddr3_load_patterns(MV_DRAM_INFO *dram_info, int resume) { u32 reg; /* Enable SW override - Required for the ECC Pup */ reg = reg_read(REG_DRAM_TRAINING_2_ADDR) | (1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); /* [0] = 1 - Enable SW override */ /* 0x15B8 - Training SW 2 Register */ reg_write(REG_DRAM_TRAINING_2_ADDR, reg); reg = (1 << REG_DRAM_TRAINING_AUTO_OFFS); reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ if (resume == 0) { #if defined(MV88F78X60) || defined(MV88F672X) ddr3_load_pbs_patterns(dram_info); #endif ddr3_load_dqs_patterns(dram_info); } /* Disable SW override - Must be in a different stage */ /* [0]=0 - Enable SW override */ reg = reg_read(REG_DRAM_TRAINING_2_ADDR); reg &= ~(1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS); /* 0x15B8 - Training SW 2 Register */ reg_write(REG_DRAM_TRAINING_2_ADDR, reg); reg = reg_read(REG_DRAM_TRAINING_1_ADDR) | (1 << REG_DRAM_TRAINING_1_TRNBPOINT_OFFS); reg_write(REG_DRAM_TRAINING_1_ADDR, reg); /* Set Base Addr */ #if defined(MV88F67XX) reg_write(REG_DRAM_TRAINING_PATTERN_BASE_ADDR, 0); #else if (resume == 0) reg_write(REG_DRAM_TRAINING_PATTERN_BASE_ADDR, 0); else reg_write(REG_DRAM_TRAINING_PATTERN_BASE_ADDR, RESUME_RL_PATTERNS_ADDR); #endif /* Set Patterns */ if (resume == 0) { reg = (dram_info->cs_ena << REG_DRAM_TRAINING_CS_OFFS) | (1 << REG_DRAM_TRAINING_PATTERNS_OFFS); } else { reg = (0x1 << REG_DRAM_TRAINING_CS_OFFS) | (1 << REG_DRAM_TRAINING_PATTERNS_OFFS); } reg |= (1 << REG_DRAM_TRAINING_AUTO_OFFS); reg_write(REG_DRAM_TRAINING_ADDR, reg); udelay(100); /* Check if Successful */ if (reg_read(REG_DRAM_TRAINING_ADDR) & (1 << REG_DRAM_TRAINING_ERROR_OFFS)) return MV_OK; else return MV_FAIL; } #if !defined(MV88F67XX) /* * Name: ddr3_save_training(MV_DRAM_INFO *dram_info) * Desc: saves the training results to memeory (RL,WL,PBS,Rx/Tx * Centeralization) * Args: MV_DRAM_INFO *dram_info * Notes: * Returns: None. */ void ddr3_save_training(MV_DRAM_INFO *dram_info) { u32 val, pup, tmp_cs, cs, i, dq; u32 crc = 0; u32 regs = 0; u32 *sdram_offset = (u32 *)RESUME_TRAINING_VALUES_ADDR; u32 mode_config[MAX_TRAINING_MODE]; mode_config[DQS_WR_MODE] = PUP_DQS_WR; mode_config[WL_MODE_] = PUP_WL_MODE; mode_config[RL_MODE_] = PUP_RL_MODE; mode_config[DQS_RD_MODE] = PUP_DQS_RD; mode_config[PBS_TX_DM_MODE] = PUP_PBS_TX_DM; mode_config[PBS_TX_MODE] = PUP_PBS_TX; mode_config[PBS_RX_MODE] = PUP_PBS_RX; /* num of training modes */ for (i = 0; i < MAX_TRAINING_MODE; i++) { tmp_cs = dram_info->cs_ena; /* num of CS */ for (cs = 0; cs < MAX_CS; cs++) { if (tmp_cs & (1 << cs)) { /* num of PUPs */ for (pup = 0; pup < dram_info->num_of_total_pups; pup++) { if (pup == dram_info->num_of_std_pups && dram_info->ecc_ena) pup = ECC_PUP; if (i == PBS_TX_DM_MODE) { /* * Change CS bitmask because * PBS works only with CS0 */ tmp_cs = 0x1; val = ddr3_read_pup_reg( mode_config[i], CS0, pup); } else if (i == PBS_TX_MODE || i == PBS_RX_MODE) { /* * Change CS bitmask because * PBS works only with CS0 */ tmp_cs = 0x1; for (dq = 0; dq <= DQ_NUM; dq++) { val = ddr3_read_pup_reg( mode_config[i] + dq, CS0, pup); (*sdram_offset) = val; crc += *sdram_offset; sdram_offset++; regs++; } continue; } else { val = ddr3_read_pup_reg( mode_config[i], cs, pup); } *sdram_offset = val; crc += *sdram_offset; sdram_offset++; regs++; } } } } *sdram_offset = reg_read(REG_READ_DATA_SAMPLE_DELAYS_ADDR); crc += *sdram_offset; sdram_offset++; regs++; *sdram_offset = reg_read(REG_READ_DATA_READY_DELAYS_ADDR); crc += *sdram_offset; sdram_offset++; regs++; sdram_offset = (u32 *)NUM_OF_REGISTER_ADDR; *sdram_offset = regs; DEBUG_SUSPEND_RESUME_S("Training Results CheckSum write= "); DEBUG_SUSPEND_RESUME_D(crc, 8); DEBUG_SUSPEND_RESUME_S("\n"); sdram_offset = (u32 *)CHECKSUM_RESULT_ADDR; *sdram_offset = crc; } /* * Name: ddr3_read_training_results() * Desc: Reads the training results from memeory (RL,WL,PBS,Rx/Tx * Centeralization) * and writes them to the relevant registers * Args: MV_DRAM_INFO *dram_info * Notes: * Returns: None. */ int ddr3_read_training_results(void) { u32 val, reg, idx, dqs_wr_idx = 0, crc = 0; u32 *sdram_offset = (u32 *)RESUME_TRAINING_VALUES_ADDR; u32 training_val[RESUME_TRAINING_VALUES_MAX] = { 0 }; u32 regs = *((u32 *)NUM_OF_REGISTER_ADDR); /* * Read Training results & Dunit registers from memory and write * it to an array */ for (idx = 0; idx < regs; idx++) { training_val[idx] = *sdram_offset; crc += *sdram_offset; sdram_offset++; } sdram_offset = (u32 *)CHECKSUM_RESULT_ADDR; if ((*sdram_offset) == crc) { DEBUG_SUSPEND_RESUME_S("Training Results CheckSum read PASS= "); DEBUG_SUSPEND_RESUME_D(crc, 8); DEBUG_SUSPEND_RESUME_S("\n"); } else { DEBUG_MAIN_S("Wrong Training Results CheckSum\n"); return MV_FAIL; } /* * We iterate through all the registers except for the last 2 since * they are Dunit registers (and not PHY registers) */ for (idx = 0; idx < (regs - 2); idx++) { val = training_val[idx]; reg = (val >> REG_PHY_CS_OFFS) & 0x3F; /*read the phy address */ /* Check if the values belongs to the DQS WR */ if (reg == PUP_WL_MODE) { /* bit[5:0] in DQS_WR are delay */ val = (training_val[dqs_wr_idx++] & 0x3F); /* * bit[15:10] are DQS_WR delay & bit[9:0] are * WL phase & delay */ val = (val << REG_PHY_DQS_REF_DLY_OFFS) | (training_val[idx] & 0x3C003FF); /* Add Request pending and write operation bits */ val |= REG_PHY_REGISTRY_FILE_ACCESS_OP_WR; } else if (reg == PUP_DQS_WR) { /* * Do nothing since DQS_WR will be done in PUP_WL_MODE */ continue; } val |= REG_PHY_REGISTRY_FILE_ACCESS_OP_WR; reg_write(REG_PHY_REGISTRY_FILE_ACCESS_ADDR, val); do { val = (reg_read(REG_PHY_REGISTRY_FILE_ACCESS_ADDR)) & REG_PHY_REGISTRY_FILE_ACCESS_OP_DONE; } while (val); /* Wait for '0' to mark the end of the transaction */ } /* write last 2 Dunit configurations */ val = training_val[idx]; reg_write(REG_READ_DATA_SAMPLE_DELAYS_ADDR, val); /* reg 0x1538 */ val = training_val[idx + 1]; reg_write(REG_READ_DATA_READY_DELAYS_ADDR, val); /* reg 0x153c */ return MV_OK; } /* * Name: ddr3_check_if_resume_mode() * Desc: Reads the address (0x3000) of the Resume Magic word (0xDEADB002) * Args: MV_DRAM_INFO *dram_info * Notes: * Returns: return (magic_word == SUSPEND_MAGIC_WORD) */ int ddr3_check_if_resume_mode(MV_DRAM_INFO *dram_info, u32 freq) { u32 magic_word; u32 *sdram_offset = (u32 *)BOOT_INFO_ADDR; if (dram_info->reg_dimm != 1) { /* * Perform write levleling in order initiate the phy with * low frequency */ if (MV_OK != ddr3_write_leveling_hw(freq, dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Write Leveling Hw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } } if (MV_OK != ddr3_load_patterns(dram_info, 1)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Loading Patterns)\n"); return MV_DDR3_TRAINING_ERR_LOAD_PATTERNS; } /* Enable CS0 only for RL */ dram_info->cs_ena = 0x1; /* Perform Read levleling in order to get stable memory */ if (MV_OK != ddr3_read_leveling_hw(freq, dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Read Leveling Hw)\n"); return MV_DDR3_TRAINING_ERR_WR_LVL_HW; } /* Back to relevant CS */ dram_info->cs_ena = ddr3_get_cs_ena_from_reg(); magic_word = *sdram_offset; return magic_word == SUSPEND_MAGIC_WORD; } /* * Name: ddr3_training_suspend_resume() * Desc: Execute the Resume state * Args: MV_DRAM_INFO *dram_info * Notes: * Returns: return (magic_word == SUSPEND_MAGIC_WORD) */ int ddr3_training_suspend_resume(MV_DRAM_INFO *dram_info) { u32 freq, reg; int tmp_ratio; /* Configure DDR */ if (MV_OK != ddr3_read_training_results()) return MV_FAIL; /* Reset read FIFO */ reg = reg_read(REG_DRAM_TRAINING_ADDR); /* Start Auto Read Leveling procedure */ reg |= (1 << REG_DRAM_TRAINING_RL_OFFS); reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ reg = reg_read(REG_DRAM_TRAINING_2_ADDR); reg |= ((1 << REG_DRAM_TRAINING_2_FIFO_RST_OFFS) + (1 << REG_DRAM_TRAINING_2_SW_OVRD_OFFS)); /* [0] = 1 - Enable SW override, [4] = 1 - FIFO reset */ /* 0x15B8 - Training SW 2 Register */ reg_write(REG_DRAM_TRAINING_2_ADDR, reg); udelay(2); reg = reg_read(REG_DRAM_TRAINING_ADDR); /* Clear Auto Read Leveling procedure */ reg &= ~(1 << REG_DRAM_TRAINING_RL_OFFS); reg_write(REG_DRAM_TRAINING_ADDR, reg); /* 0x15B0 - Training Register */ /* Return to target frequency */ freq = dram_info->target_frequency; tmp_ratio = 1; if (MV_OK != ddr3_dfs_low_2_high(freq, tmp_ratio, dram_info)) { DEBUG_MAIN_S("DDR3 Training Sequence - FAILED (Dfs Low2High)\n"); return MV_DDR3_TRAINING_ERR_DFS_H2L; } if (dram_info->ecc_ena) { /* Scabbling the RL area pattern and the training area */ mv_sys_xor_finish(); dram_info->num_cs = 1; dram_info->cs_ena = 1; mv_sys_xor_init(dram_info); mv_xor_mem_init(0, RESUME_RL_PATTERNS_ADDR, RESUME_RL_PATTERNS_SIZE, 0xFFFFFFFF, 0xFFFFFFFF); /* Wait for previous transfer completion */ while (mv_xor_state_get(0) != MV_IDLE) ; /* Return XOR State */ mv_sys_xor_finish(); } return MV_OK; } #endif void ddr3_print_freq(u32 freq) { u32 tmp_freq; switch (freq) { case 0: tmp_freq = 100; break; case 1: tmp_freq = 300; break; case 2: tmp_freq = 360; break; case 3: tmp_freq = 400; break; case 4: tmp_freq = 444; break; case 5: tmp_freq = 500; break; case 6: tmp_freq = 533; break; case 7: tmp_freq = 600; break; case 8: tmp_freq = 666; break; case 9: tmp_freq = 720; break; case 10: tmp_freq = 800; break; default: tmp_freq = 100; } printf("Current frequency is: %dMHz\n", tmp_freq); } int ddr3_get_min_max_read_sample_delay(u32 cs_enable, u32 reg, u32 *min, u32 *max, u32 *cs_max) { u32 cs, delay; *min = 0xFFFFFFFF; *max = 0x0; for (cs = 0; cs < MAX_CS; cs++) { if ((cs_enable & (1 << cs)) == 0) continue; delay = ((reg >> (cs * 8)) & 0x1F); if (delay < *min) *min = delay; if (delay > *max) { *max = delay; *cs_max = cs; } } return MV_OK; } int ddr3_get_min_max_rl_phase(MV_DRAM_INFO *dram_info, u32 *min, u32 *max, u32 cs) { u32 pup, reg, phase; *min = 0xFFFFFFFF; *max = 0x0; for (pup = 0; pup < dram_info->num_of_total_pups; pup++) { reg = ddr3_read_pup_reg(PUP_RL_MODE, cs, pup); phase = ((reg >> 8) & 0x7); if (phase < *min) *min = phase; if (phase > *max) *max = phase; } return MV_OK; } int ddr3_odt_activate(int activate) { u32 reg, mask; mask = (1 << REG_DUNIT_ODT_CTRL_OVRD_OFFS) | (1 << REG_DUNIT_ODT_CTRL_OVRD_VAL_OFFS); /* {0x0000149C} - DDR Dunit ODT Control Register */ reg = reg_read(REG_DUNIT_ODT_CTRL_ADDR); if (activate) reg |= mask; else reg &= ~mask; reg_write(REG_DUNIT_ODT_CTRL_ADDR, reg); return MV_OK; } int ddr3_odt_read_dynamic_config(MV_DRAM_INFO *dram_info) { u32 min_read_sample_delay, max_read_sample_delay, max_rl_phase; u32 min, max, cs_max; u32 cs_ena, reg; reg = reg_read(REG_READ_DATA_SAMPLE_DELAYS_ADDR); cs_ena = ddr3_get_cs_ena_from_reg(); /* Get minimum and maximum of read sample delay of all CS */ ddr3_get_min_max_read_sample_delay(cs_ena, reg, &min_read_sample_delay, &max_read_sample_delay, &cs_max); /* * Get minimum and maximum read leveling phase which belongs to the * maximal read sample delay */ ddr3_get_min_max_rl_phase(dram_info, &min, &max, cs_max); max_rl_phase = max; /* DDR ODT Timing (Low) Register calculation */ reg = reg_read(REG_ODT_TIME_LOW_ADDR); reg &= ~(0x1FF << REG_ODT_ON_CTL_RD_OFFS); reg |= (((min_read_sample_delay - 1) & 0xF) << REG_ODT_ON_CTL_RD_OFFS); reg |= (((max_read_sample_delay + 4 + (((max_rl_phase + 1) / 2) + 1)) & 0x1F) << REG_ODT_OFF_CTL_RD_OFFS); reg_write(REG_ODT_TIME_LOW_ADDR, reg); return MV_OK; }