// SPDX-License-Identifier: GPL-2.0 /* * AM625: SoC specific initialization * * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/ * Suman Anna */ #include #include #include #include "sysfw-loader.h" #include "common.h" #include #include #include #define RTC_BASE_ADDRESS 0x2b1f0000 #define REG_K3RTC_S_CNT_LSW (RTC_BASE_ADDRESS + 0x18) #define REG_K3RTC_KICK0 (RTC_BASE_ADDRESS + 0x70) #define REG_K3RTC_KICK1 (RTC_BASE_ADDRESS + 0x74) /* Magic values for lock/unlock */ #define K3RTC_KICK0_UNLOCK_VALUE 0x83e70b13 #define K3RTC_KICK1_UNLOCK_VALUE 0x95a4f1e0 /* * This uninitialized global variable would normal end up in the .bss section, * but the .bss is cleared between writing and reading this variable, so move * it to the .data section. */ u32 bootindex __section(".data"); static struct rom_extended_boot_data bootdata __section(".data"); static void store_boot_info_from_rom(void) { bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX); memcpy(&bootdata, (uintptr_t *)ROM_EXTENDED_BOOT_DATA_INFO, sizeof(struct rom_extended_boot_data)); } static void ctrl_mmr_unlock(void) { /* Unlock all WKUP_CTRL_MMR0 module registers */ mmr_unlock(WKUP_CTRL_MMR0_BASE, 0); mmr_unlock(WKUP_CTRL_MMR0_BASE, 1); mmr_unlock(WKUP_CTRL_MMR0_BASE, 2); mmr_unlock(WKUP_CTRL_MMR0_BASE, 3); mmr_unlock(WKUP_CTRL_MMR0_BASE, 4); mmr_unlock(WKUP_CTRL_MMR0_BASE, 5); mmr_unlock(WKUP_CTRL_MMR0_BASE, 6); mmr_unlock(WKUP_CTRL_MMR0_BASE, 7); /* Unlock all CTRL_MMR0 module registers */ mmr_unlock(CTRL_MMR0_BASE, 0); mmr_unlock(CTRL_MMR0_BASE, 1); mmr_unlock(CTRL_MMR0_BASE, 2); mmr_unlock(CTRL_MMR0_BASE, 4); mmr_unlock(CTRL_MMR0_BASE, 6); /* Unlock all MCU_CTRL_MMR0 module registers */ mmr_unlock(MCU_CTRL_MMR0_BASE, 0); mmr_unlock(MCU_CTRL_MMR0_BASE, 1); mmr_unlock(MCU_CTRL_MMR0_BASE, 2); mmr_unlock(MCU_CTRL_MMR0_BASE, 3); mmr_unlock(MCU_CTRL_MMR0_BASE, 4); mmr_unlock(MCU_CTRL_MMR0_BASE, 6); /* Unlock PADCFG_CTRL_MMR padconf registers */ mmr_unlock(PADCFG_MMR0_BASE, 1); mmr_unlock(PADCFG_MMR1_BASE, 1); } static __maybe_unused void enable_mcu_esm_reset(void) { /* Set CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RST_EN_Z to '0' (low active) */ u32 stat = readl(CTRLMMR_MCU_RST_CTRL); stat &= RST_CTRL_ESM_ERROR_RST_EN_Z_MASK; writel(stat, CTRLMMR_MCU_RST_CTRL); } /* * RTC Erratum i2327 Workaround for Silicon Revision 1 * * Due to a bug in initial synchronization out of cold power on, * IRQ status can get locked infinitely if we do not unlock RTC * * This workaround *must* be applied within 1 second of power on, * So, this is closest point to be able to guarantee the max * timing. * * https://www.ti.com/lit/er/sprz487c/sprz487c.pdf */ static __maybe_unused void rtc_erratumi2327_init(void) { u32 counter; /* * If counter has gone past 1, nothing we can do, leave * system locked! This is the only way we know if RTC * can be used for all practical purposes. */ counter = readl(REG_K3RTC_S_CNT_LSW); if (counter > 1) return; /* * Need to set this up at the very start * MUST BE DONE under 1 second of boot. */ writel(K3RTC_KICK0_UNLOCK_VALUE, REG_K3RTC_KICK0); writel(K3RTC_KICK1_UNLOCK_VALUE, REG_K3RTC_KICK1); } void board_init_f(ulong dummy) { struct udevice *dev; int ret; if (IS_ENABLED(CONFIG_CPU_V7R)) { setup_k3_mpu_regions(); rtc_erratumi2327_init(); } /* * Cannot delay this further as there is a chance that * K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section. */ store_boot_info_from_rom(); ctrl_mmr_unlock(); /* Init DM early */ spl_early_init(); /* * Process pinctrl for the serial0 and serial3, aka WKUP_UART0 and * MAIN_UART1 modules and continue regardless of the result of pinctrl. * Do this without probing the device, but instead by searching the * device that would request the given sequence number if probed. The * UARTs will be used by the DM firmware and TIFS firmware images * respectively and the firmware depend on SPL to initialize the pin * settings. */ ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, &dev); if (!ret) pinctrl_select_state(dev, "default"); ret = uclass_find_device_by_seq(UCLASS_SERIAL, 3, &dev); if (!ret) pinctrl_select_state(dev, "default"); preloader_console_init(); /* * Allow establishing an early console as required for example when * doing a UART-based boot. Note that this console may not "survive" * through a SYSFW PM-init step and will need a re-init in some way * due to changing module clock frequencies. */ if (IS_ENABLED(CONFIG_K3_EARLY_CONS)) early_console_init(); /* * Configure and start up system controller firmware. Provide * the U-Boot console init function to the SYSFW post-PM configuration * callback hook, effectively switching on (or over) the console * output. */ if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) { ret = is_rom_loaded_sysfw(&bootdata); if (!ret) panic("ROM has not loaded TIFS firmware\n"); k3_sysfw_loader(true, NULL, NULL); } /* * Force probe of clk_k3 driver here to ensure basic default clock * configuration is always done. */ if (IS_ENABLED(CONFIG_SPL_CLK_K3)) { ret = uclass_get_device_by_driver(UCLASS_CLK, DM_DRIVER_GET(ti_clk), &dev); if (ret) printf("Failed to initialize clk-k3!\n"); } /* Output System Firmware version info */ k3_sysfw_print_ver(); if (IS_ENABLED(CONFIG_ESM_K3)) { /* Probe/configure ESM0 */ ret = uclass_get_device_by_name(UCLASS_MISC, "esm@420000", &dev); if (ret) printf("esm main init failed: %d\n", ret); /* Probe/configure MCUESM */ ret = uclass_get_device_by_name(UCLASS_MISC, "esm@4100000", &dev); if (ret) printf("esm mcu init failed: %d\n", ret); enable_mcu_esm_reset(); } if (IS_ENABLED(CONFIG_K3_AM64_DDRSS)) { ret = uclass_get_device(UCLASS_RAM, 0, &dev); if (ret) panic("DRAM init failed: %d\n", ret); } spl_enable_dcache(); } u32 spl_mmc_boot_mode(struct mmc *mmc, const u32 boot_device) { u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT); u32 bootmode = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_MASK) >> MAIN_DEVSTAT_PRIMARY_BOOTMODE_SHIFT; u32 bootmode_cfg = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_MASK) >> MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_SHIFT; switch (bootmode) { case BOOT_DEVICE_EMMC: return MMCSD_MODE_EMMCBOOT; case BOOT_DEVICE_MMC: if (bootmode_cfg & MAIN_DEVSTAT_PRIMARY_MMC_FS_RAW_MASK) return MMCSD_MODE_RAW; default: return MMCSD_MODE_FS; } } static u32 __get_backup_bootmedia(u32 devstat) { u32 bkup_bootmode = (devstat & MAIN_DEVSTAT_BACKUP_BOOTMODE_MASK) >> MAIN_DEVSTAT_BACKUP_BOOTMODE_SHIFT; u32 bkup_bootmode_cfg = (devstat & MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_MASK) >> MAIN_DEVSTAT_BACKUP_BOOTMODE_CFG_SHIFT; switch (bkup_bootmode) { case BACKUP_BOOT_DEVICE_UART: return BOOT_DEVICE_UART; case BACKUP_BOOT_DEVICE_USB: return BOOT_DEVICE_USB; case BACKUP_BOOT_DEVICE_ETHERNET: return BOOT_DEVICE_ETHERNET; case BACKUP_BOOT_DEVICE_MMC: if (bkup_bootmode_cfg) return BOOT_DEVICE_MMC2; return BOOT_DEVICE_MMC1; case BACKUP_BOOT_DEVICE_SPI: return BOOT_DEVICE_SPI; case BACKUP_BOOT_DEVICE_I2C: return BOOT_DEVICE_I2C; case BACKUP_BOOT_DEVICE_DFU: if (bkup_bootmode_cfg & MAIN_DEVSTAT_BACKUP_USB_MODE_MASK) return BOOT_DEVICE_USB; return BOOT_DEVICE_DFU; }; return BOOT_DEVICE_RAM; } static u32 __get_primary_bootmedia(u32 devstat) { u32 bootmode = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_MASK) >> MAIN_DEVSTAT_PRIMARY_BOOTMODE_SHIFT; u32 bootmode_cfg = (devstat & MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_MASK) >> MAIN_DEVSTAT_PRIMARY_BOOTMODE_CFG_SHIFT; switch (bootmode) { case BOOT_DEVICE_OSPI: fallthrough; case BOOT_DEVICE_QSPI: fallthrough; case BOOT_DEVICE_XSPI: fallthrough; case BOOT_DEVICE_SPI: return BOOT_DEVICE_SPI; case BOOT_DEVICE_ETHERNET_RGMII: fallthrough; case BOOT_DEVICE_ETHERNET_RMII: return BOOT_DEVICE_ETHERNET; case BOOT_DEVICE_EMMC: return BOOT_DEVICE_MMC1; case BOOT_DEVICE_MMC: if ((bootmode_cfg & MAIN_DEVSTAT_PRIMARY_MMC_PORT_MASK) >> MAIN_DEVSTAT_PRIMARY_MMC_PORT_SHIFT) return BOOT_DEVICE_MMC2; return BOOT_DEVICE_MMC1; case BOOT_DEVICE_DFU: if ((bootmode_cfg & MAIN_DEVSTAT_PRIMARY_USB_MODE_MASK) >> MAIN_DEVSTAT_PRIMARY_USB_MODE_SHIFT) return BOOT_DEVICE_USB; return BOOT_DEVICE_DFU; case BOOT_DEVICE_NOBOOT: return BOOT_DEVICE_RAM; } return bootmode; } u32 spl_boot_device(void) { u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT); u32 bootmedia; if (bootindex == K3_PRIMARY_BOOTMODE) bootmedia = __get_primary_bootmedia(devstat); else bootmedia = __get_backup_bootmedia(devstat); debug("am625_init: %s: devstat = 0x%x bootmedia = 0x%x bootindex = %d\n", __func__, devstat, bootmedia, bootindex); return bootmedia; }