// SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2021 Waymo LLC * Copyright (C) 2011 Michal Simek * Copyright (C) 2011 PetaLogix * Copyright (C) 2010 Xilinx, Inc. All rights reserved. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include DECLARE_GLOBAL_DATA_PTR; /* Link setup */ #define XAE_EMMC_LINKSPEED_MASK 0xC0000000 /* Link speed */ #define XAE_EMMC_LINKSPD_10 0x00000000 /* Link Speed mask for 10 Mbit */ #define XAE_EMMC_LINKSPD_100 0x40000000 /* Link Speed mask for 100 Mbit */ #define XAE_EMMC_LINKSPD_1000 0x80000000 /* Link Speed mask for 1000 Mbit */ /* Interrupt Status/Enable/Mask Registers bit definitions */ #define XAE_INT_RXRJECT_MASK 0x00000008 /* Rx frame rejected */ #define XAE_INT_MGTRDY_MASK 0x00000080 /* MGT clock Lock */ /* Receive Configuration Word 1 (RCW1) Register bit definitions */ #define XAE_RCW1_RX_MASK 0x10000000 /* Receiver enable */ /* Transmitter Configuration (TC) Register bit definitions */ #define XAE_TC_TX_MASK 0x10000000 /* Transmitter enable */ #define XAE_UAW1_UNICASTADDR_MASK 0x0000FFFF /* MDIO Management Configuration (MC) Register bit definitions */ #define XAE_MDIO_MC_MDIOEN_MASK 0x00000040 /* MII management enable*/ /* MDIO Management Control Register (MCR) Register bit definitions */ #define XAE_MDIO_MCR_PHYAD_MASK 0x1F000000 /* Phy Address Mask */ #define XAE_MDIO_MCR_PHYAD_SHIFT 24 /* Phy Address Shift */ #define XAE_MDIO_MCR_REGAD_MASK 0x001F0000 /* Reg Address Mask */ #define XAE_MDIO_MCR_REGAD_SHIFT 16 /* Reg Address Shift */ #define XAE_MDIO_MCR_OP_READ_MASK 0x00008000 /* Op Code Read Mask */ #define XAE_MDIO_MCR_OP_WRITE_MASK 0x00004000 /* Op Code Write Mask */ #define XAE_MDIO_MCR_INITIATE_MASK 0x00000800 /* Ready Mask */ #define XAE_MDIO_MCR_READY_MASK 0x00000080 /* Ready Mask */ #define XAE_MDIO_DIV_DFT 29 /* Default MDIO clock divisor */ #define XAXIDMA_BD_STS_ACTUAL_LEN_MASK 0x007FFFFF /* Actual len */ /* DMA macros */ /* Bitmasks of XAXIDMA_CR_OFFSET register */ #define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */ #define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */ /* Bitmasks of XAXIDMA_SR_OFFSET register */ #define XAXIDMA_HALTED_MASK 0x00000001 /* DMA channel halted */ /* Bitmask for interrupts */ #define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */ #define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */ #define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */ /* Bitmasks of XAXIDMA_BD_CTRL_OFFSET register */ #define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */ #define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */ /* Bitmasks for XXV Ethernet MAC */ #define XXV_TC_TX_MASK 0x00000001 #define XXV_TC_FCS_MASK 0x00000002 #define XXV_RCW1_RX_MASK 0x00000001 #define XXV_RCW1_FCS_MASK 0x00000002 #define DMAALIGN 128 #define XXV_MIN_PKT_SIZE 60 static u8 rxframe[PKTSIZE_ALIGN] __attribute((aligned(DMAALIGN))); static u8 txminframe[XXV_MIN_PKT_SIZE] __attribute((aligned(DMAALIGN))); enum emac_variant { EMAC_1G = 0, EMAC_10G_25G = 1, }; /* Reflect dma offsets */ struct axidma_reg { u32 control; /* DMACR */ u32 status; /* DMASR */ u32 current; /* CURDESC low 32 bit */ u32 current_hi; /* CURDESC high 32 bit */ u32 tail; /* TAILDESC low 32 bit */ u32 tail_hi; /* TAILDESC high 32 bit */ }; /* Platform data structures */ struct axidma_plat { struct eth_pdata eth_pdata; struct axidma_reg *dmatx; struct axidma_reg *dmarx; int phyaddr; u8 eth_hasnobuf; int phy_of_handle; enum emac_variant mactype; }; /* Private driver structures */ struct axidma_priv { struct axidma_reg *dmatx; struct axidma_reg *dmarx; int phyaddr; struct axi_regs *iobase; phy_interface_t interface; struct phy_device *phydev; struct mii_dev *bus; u8 eth_hasnobuf; int phy_of_handle; enum emac_variant mactype; }; /* BD descriptors */ struct axidma_bd { u32 next_desc; /* Next descriptor pointer */ u32 next_desc_msb; u32 buf_addr; /* Buffer address */ u32 buf_addr_msb; u32 reserved3; u32 reserved4; u32 cntrl; /* Control */ u32 status; /* Status */ u32 app0; u32 app1; /* TX start << 16 | insert */ u32 app2; /* TX csum seed */ u32 app3; u32 app4; u32 sw_id_offset; u32 reserved5; u32 reserved6; }; /* Static BDs - driver uses only one BD */ static struct axidma_bd tx_bd __attribute((aligned(DMAALIGN))); static struct axidma_bd rx_bd __attribute((aligned(DMAALIGN))); struct axi_regs { u32 reserved[3]; u32 is; /* 0xC: Interrupt status */ u32 reserved2; u32 ie; /* 0x14: Interrupt enable */ u32 reserved3[251]; u32 rcw1; /* 0x404: Rx Configuration Word 1 */ u32 tc; /* 0x408: Tx Configuration */ u32 reserved4; u32 emmc; /* 0x410: EMAC mode configuration */ u32 reserved5[59]; u32 mdio_mc; /* 0x500: MII Management Config */ u32 mdio_mcr; /* 0x504: MII Management Control */ u32 mdio_mwd; /* 0x508: MII Management Write Data */ u32 mdio_mrd; /* 0x50C: MII Management Read Data */ u32 reserved6[124]; u32 uaw0; /* 0x700: Unicast address word 0 */ u32 uaw1; /* 0x704: Unicast address word 1 */ }; struct xxv_axi_regs { u32 gt_reset; /* 0x0 */ u32 reserved[2]; u32 tc; /* 0xC: Tx Configuration */ u32 reserved2; u32 rcw1; /* 0x14: Rx Configuration Word 1 */ }; /* Use MII register 1 (MII status register) to detect PHY */ #define PHY_DETECT_REG 1 /* * Mask used to verify certain PHY features (or register contents) * in the register above: * 0x1000: 10Mbps full duplex support * 0x0800: 10Mbps half duplex support * 0x0008: Auto-negotiation support */ #define PHY_DETECT_MASK 0x1808 static inline int mdio_wait(struct axi_regs *regs) { u32 timeout = 200; /* Wait till MDIO interface is ready to accept a new transaction. */ while (timeout && (!(readl(®s->mdio_mcr) & XAE_MDIO_MCR_READY_MASK))) { timeout--; udelay(1); } if (!timeout) { printf("%s: Timeout\n", __func__); return 1; } return 0; } /** * axienet_dma_write - Memory mapped Axi DMA register Buffer Descriptor write. * @bd: pointer to BD descriptor structure * @desc: Address offset of DMA descriptors * * This function writes the value into the corresponding Axi DMA register. */ static inline void axienet_dma_write(struct axidma_bd *bd, u32 *desc) { #if defined(CONFIG_PHYS_64BIT) writeq((unsigned long)bd, desc); #else writel((u32)bd, desc); #endif } static u32 phyread(struct axidma_priv *priv, u32 phyaddress, u32 registernum, u16 *val) { struct axi_regs *regs = priv->iobase; u32 mdioctrlreg = 0; if (mdio_wait(regs)) return 1; mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) & XAE_MDIO_MCR_PHYAD_MASK) | ((registernum << XAE_MDIO_MCR_REGAD_SHIFT) & XAE_MDIO_MCR_REGAD_MASK) | XAE_MDIO_MCR_INITIATE_MASK | XAE_MDIO_MCR_OP_READ_MASK; writel(mdioctrlreg, ®s->mdio_mcr); if (mdio_wait(regs)) return 1; /* Read data */ *val = readl(®s->mdio_mrd); return 0; } static u32 phywrite(struct axidma_priv *priv, u32 phyaddress, u32 registernum, u32 data) { struct axi_regs *regs = priv->iobase; u32 mdioctrlreg = 0; if (mdio_wait(regs)) return 1; mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) & XAE_MDIO_MCR_PHYAD_MASK) | ((registernum << XAE_MDIO_MCR_REGAD_SHIFT) & XAE_MDIO_MCR_REGAD_MASK) | XAE_MDIO_MCR_INITIATE_MASK | XAE_MDIO_MCR_OP_WRITE_MASK; /* Write data */ writel(data, ®s->mdio_mwd); writel(mdioctrlreg, ®s->mdio_mcr); if (mdio_wait(regs)) return 1; return 0; } static int axiemac_phy_init(struct udevice *dev) { u16 phyreg; int i; u32 ret; struct axidma_priv *priv = dev_get_priv(dev); struct axi_regs *regs = priv->iobase; struct phy_device *phydev; u32 supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full; /* Set default MDIO divisor */ writel(XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK, ®s->mdio_mc); if (IS_ENABLED(CONFIG_DM_ETH_PHY)) priv->phyaddr = eth_phy_get_addr(dev); if (priv->phyaddr == -1) { /* Detect the PHY address */ for (i = 31; i >= 0; i--) { ret = phyread(priv, i, PHY_DETECT_REG, &phyreg); if (!ret && (phyreg != 0xFFFF) && ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) { /* Found a valid PHY address */ priv->phyaddr = i; debug("axiemac: Found valid phy address, %x\n", i); break; } } } /* Interface - look at tsec */ phydev = phy_connect(priv->bus, priv->phyaddr, dev, priv->interface); phydev->supported &= supported; phydev->advertising = phydev->supported; priv->phydev = phydev; if (priv->phy_of_handle) priv->phydev->node = offset_to_ofnode(priv->phy_of_handle); phy_config(phydev); return 0; } /* Setting axi emac and phy to proper setting */ static int setup_phy(struct udevice *dev) { u16 temp; u32 speed, emmc_reg, ret; struct axidma_priv *priv = dev_get_priv(dev); struct axi_regs *regs = priv->iobase; struct phy_device *phydev = priv->phydev; if (priv->interface == PHY_INTERFACE_MODE_SGMII) { /* * In SGMII cases the isolate bit might set * after DMA and ethernet resets and hence * check and clear if set. */ ret = phyread(priv, priv->phyaddr, MII_BMCR, &temp); if (ret) return 0; if (temp & BMCR_ISOLATE) { temp &= ~BMCR_ISOLATE; ret = phywrite(priv, priv->phyaddr, MII_BMCR, temp); if (ret) return 0; } } if (phy_startup(phydev)) { printf("axiemac: could not initialize PHY %s\n", phydev->dev->name); return 0; } if (!phydev->link) { printf("%s: No link.\n", phydev->dev->name); return 0; } switch (phydev->speed) { case 1000: speed = XAE_EMMC_LINKSPD_1000; break; case 100: speed = XAE_EMMC_LINKSPD_100; break; case 10: speed = XAE_EMMC_LINKSPD_10; break; default: return 0; } /* Setup the emac for the phy speed */ emmc_reg = readl(®s->emmc); emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK; emmc_reg |= speed; /* Write new speed setting out to Axi Ethernet */ writel(emmc_reg, ®s->emmc); /* * Setting the operating speed of the MAC needs a delay. There * doesn't seem to be register to poll, so please consider this * during your application design. */ udelay(1); return 1; } /* STOP DMA transfers */ static void axiemac_stop(struct udevice *dev) { struct axidma_priv *priv = dev_get_priv(dev); u32 temp; /* Stop the hardware */ temp = readl(&priv->dmatx->control); temp &= ~XAXIDMA_CR_RUNSTOP_MASK; writel(temp, &priv->dmatx->control); temp = readl(&priv->dmarx->control); temp &= ~XAXIDMA_CR_RUNSTOP_MASK; writel(temp, &priv->dmarx->control); debug("axiemac: Halted\n"); } static int xxv_axi_ethernet_init(struct axidma_priv *priv) { struct xxv_axi_regs *regs = (struct xxv_axi_regs *)priv->iobase; writel(readl(®s->rcw1) | XXV_RCW1_FCS_MASK, ®s->rcw1); writel(readl(®s->tc) | XXV_TC_FCS_MASK, ®s->tc); writel(readl(®s->tc) | XXV_TC_TX_MASK, ®s->tc); writel(readl(®s->rcw1) | XXV_RCW1_RX_MASK, ®s->rcw1); return 0; } static int axi_ethernet_init(struct axidma_priv *priv) { struct axi_regs *regs = priv->iobase; int err; /* * Check the status of the MgtRdy bit in the interrupt status * registers. This must be done to allow the MGT clock to become stable * for the Sgmii and 1000BaseX PHY interfaces. No other register reads * will be valid until this bit is valid. * The bit is always a 1 for all other PHY interfaces. * Interrupt status and enable registers are not available in non * processor mode and hence bypass in this mode */ if (!priv->eth_hasnobuf) { err = wait_for_bit_le32(®s->is, XAE_INT_MGTRDY_MASK, true, 200, false); if (err) { printf("%s: Timeout\n", __func__); return 1; } /* * Stop the device and reset HW * Disable interrupts */ writel(0, ®s->ie); } /* Disable the receiver */ writel(readl(®s->rcw1) & ~XAE_RCW1_RX_MASK, ®s->rcw1); /* * Stopping the receiver in mid-packet causes a dropped packet * indication from HW. Clear it. */ if (!priv->eth_hasnobuf) { /* Set the interrupt status register to clear the interrupt */ writel(XAE_INT_RXRJECT_MASK, ®s->is); } /* Setup HW */ /* Set default MDIO divisor */ writel(XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK, ®s->mdio_mc); debug("axiemac: InitHw done\n"); return 0; } static int axiemac_write_hwaddr(struct udevice *dev) { struct eth_pdata *pdata = dev_get_plat(dev); struct axidma_priv *priv = dev_get_priv(dev); struct axi_regs *regs = priv->iobase; if (priv->mactype != EMAC_1G) return 0; /* Set the MAC address */ int val = ((pdata->enetaddr[3] << 24) | (pdata->enetaddr[2] << 16) | (pdata->enetaddr[1] << 8) | (pdata->enetaddr[0])); writel(val, ®s->uaw0); val = (pdata->enetaddr[5] << 8) | pdata->enetaddr[4]; val |= readl(®s->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK; writel(val, ®s->uaw1); return 0; } /* Reset DMA engine */ static void axi_dma_init(struct axidma_priv *priv) { u32 timeout = 500; /* Reset the engine so the hardware starts from a known state */ writel(XAXIDMA_CR_RESET_MASK, &priv->dmatx->control); writel(XAXIDMA_CR_RESET_MASK, &priv->dmarx->control); /* At the initialization time, hardware should finish reset quickly */ while (timeout--) { /* Check transmit/receive channel */ /* Reset is done when the reset bit is low */ if (!((readl(&priv->dmatx->control) | readl(&priv->dmarx->control)) & XAXIDMA_CR_RESET_MASK)) { break; } } if (!timeout) printf("%s: Timeout\n", __func__); } static int axiemac_start(struct udevice *dev) { struct axidma_priv *priv = dev_get_priv(dev); u32 temp; debug("axiemac: Init started\n"); /* * Initialize AXIDMA engine. AXIDMA engine must be initialized before * AxiEthernet. During AXIDMA engine initialization, AXIDMA hardware is * reset, and since AXIDMA reset line is connected to AxiEthernet, this * would ensure a reset of AxiEthernet. */ axi_dma_init(priv); /* Initialize AxiEthernet hardware. */ if (priv->mactype == EMAC_1G) { if (axi_ethernet_init(priv)) return -1; } else { if (xxv_axi_ethernet_init(priv)) return -1; } /* Disable all RX interrupts before RxBD space setup */ temp = readl(&priv->dmarx->control); temp &= ~XAXIDMA_IRQ_ALL_MASK; writel(temp, &priv->dmarx->control); /* Start DMA RX channel. Now it's ready to receive data.*/ axienet_dma_write(&rx_bd, &priv->dmarx->current); /* Setup the BD. */ memset(&rx_bd, 0, sizeof(rx_bd)); rx_bd.next_desc = lower_32_bits((unsigned long)&rx_bd); rx_bd.buf_addr = lower_32_bits((unsigned long)&rxframe); #if defined(CONFIG_PHYS_64BIT) rx_bd.next_desc_msb = upper_32_bits((unsigned long)&rx_bd); rx_bd.buf_addr_msb = upper_32_bits((unsigned long)&rxframe); #endif rx_bd.cntrl = sizeof(rxframe); /* Flush the last BD so DMA core could see the updates */ flush_cache((phys_addr_t)&rx_bd, sizeof(rx_bd)); /* It is necessary to flush rxframe because if you don't do it * then cache can contain uninitialized data */ flush_cache((phys_addr_t)&rxframe, sizeof(rxframe)); /* Start the hardware */ temp = readl(&priv->dmarx->control); temp |= XAXIDMA_CR_RUNSTOP_MASK; writel(temp, &priv->dmarx->control); /* Rx BD is ready - start */ axienet_dma_write(&rx_bd, &priv->dmarx->tail); if (priv->mactype == EMAC_1G) { struct axi_regs *regs = priv->iobase; /* Enable TX */ writel(XAE_TC_TX_MASK, ®s->tc); /* Enable RX */ writel(XAE_RCW1_RX_MASK, ®s->rcw1); /* PHY setup */ if (!setup_phy(dev)) { axiemac_stop(dev); return -1; } } else { struct xxv_axi_regs *regs = (struct xxv_axi_regs *)priv->iobase; /* Enable TX */ writel(readl(®s->tc) | XXV_TC_TX_MASK, ®s->tc); /* Enable RX */ writel(readl(®s->rcw1) | XXV_RCW1_RX_MASK, ®s->rcw1); } debug("axiemac: Init complete\n"); return 0; } static int axiemac_send(struct udevice *dev, void *ptr, int len) { struct axidma_priv *priv = dev_get_priv(dev); u32 timeout; if (len > PKTSIZE_ALIGN) len = PKTSIZE_ALIGN; /* If size is less than min packet size, pad to min size */ if (priv->mactype == EMAC_10G_25G && len < XXV_MIN_PKT_SIZE) { memset(txminframe, 0, XXV_MIN_PKT_SIZE); memcpy(txminframe, ptr, len); len = XXV_MIN_PKT_SIZE; ptr = txminframe; } /* Flush packet to main memory to be trasfered by DMA */ flush_cache((phys_addr_t)ptr, len); /* Setup Tx BD */ memset(&tx_bd, 0, sizeof(tx_bd)); /* At the end of the ring, link the last BD back to the top */ tx_bd.next_desc = lower_32_bits((unsigned long)&tx_bd); tx_bd.buf_addr = lower_32_bits((unsigned long)ptr); #if defined(CONFIG_PHYS_64BIT) tx_bd.next_desc_msb = upper_32_bits((unsigned long)&tx_bd); tx_bd.buf_addr_msb = upper_32_bits((unsigned long)ptr); #endif /* Save len */ tx_bd.cntrl = len | XAXIDMA_BD_CTRL_TXSOF_MASK | XAXIDMA_BD_CTRL_TXEOF_MASK; /* Flush the last BD so DMA core could see the updates */ flush_cache((phys_addr_t)&tx_bd, sizeof(tx_bd)); if (readl(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) { u32 temp; axienet_dma_write(&tx_bd, &priv->dmatx->current); /* Start the hardware */ temp = readl(&priv->dmatx->control); temp |= XAXIDMA_CR_RUNSTOP_MASK; writel(temp, &priv->dmatx->control); } /* Start transfer */ axienet_dma_write(&tx_bd, &priv->dmatx->tail); /* Wait for transmission to complete */ debug("axiemac: Waiting for tx to be done\n"); timeout = 200; while (timeout && (!(readl(&priv->dmatx->status) & (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK)))) { timeout--; udelay(1); } if (!timeout) { printf("%s: Timeout\n", __func__); return 1; } debug("axiemac: Sending complete\n"); return 0; } static int isrxready(struct axidma_priv *priv) { u32 status; /* Read pending interrupts */ status = readl(&priv->dmarx->status); /* Acknowledge pending interrupts */ writel(status & XAXIDMA_IRQ_ALL_MASK, &priv->dmarx->status); /* * If Reception done interrupt is asserted, call RX call back function * to handle the processed BDs and then raise the according flag. */ if ((status & (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK))) return 1; return 0; } static int axiemac_recv(struct udevice *dev, int flags, uchar **packetp) { u32 length; struct axidma_priv *priv = dev_get_priv(dev); u32 temp; /* Wait for an incoming packet */ if (!isrxready(priv)) return -1; debug("axiemac: RX data ready\n"); /* Disable IRQ for a moment till packet is handled */ temp = readl(&priv->dmarx->control); temp &= ~XAXIDMA_IRQ_ALL_MASK; writel(temp, &priv->dmarx->control); if (!priv->eth_hasnobuf && priv->mactype == EMAC_1G) length = rx_bd.app4 & 0xFFFF; /* max length mask */ else length = rx_bd.status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK; #ifdef DEBUG print_buffer(&rxframe, &rxframe[0], 1, length, 16); #endif *packetp = rxframe; return length; } static int axiemac_free_pkt(struct udevice *dev, uchar *packet, int length) { struct axidma_priv *priv = dev_get_priv(dev); #ifdef DEBUG /* It is useful to clear buffer to be sure that it is consistent */ memset(rxframe, 0, sizeof(rxframe)); #endif /* Setup RxBD */ /* Clear the whole buffer and setup it again - all flags are cleared */ memset(&rx_bd, 0, sizeof(rx_bd)); rx_bd.next_desc = lower_32_bits((unsigned long)&rx_bd); rx_bd.buf_addr = lower_32_bits((unsigned long)&rxframe); #if defined(CONFIG_PHYS_64BIT) rx_bd.next_desc_msb = upper_32_bits((unsigned long)&rx_bd); rx_bd.buf_addr_msb = upper_32_bits((unsigned long)&rxframe); #endif rx_bd.cntrl = sizeof(rxframe); /* Write bd to HW */ flush_cache((phys_addr_t)&rx_bd, sizeof(rx_bd)); /* It is necessary to flush rxframe because if you don't do it * then cache will contain previous packet */ flush_cache((phys_addr_t)&rxframe, sizeof(rxframe)); /* Rx BD is ready - start again */ axienet_dma_write(&rx_bd, &priv->dmarx->tail); debug("axiemac: RX completed, framelength = %d\n", length); return 0; } static int axiemac_miiphy_read(struct mii_dev *bus, int addr, int devad, int reg) { int ret; u16 value; ret = phyread(bus->priv, addr, reg, &value); debug("axiemac: Read MII 0x%x, 0x%x, 0x%x, %d\n", addr, reg, value, ret); return value; } static int axiemac_miiphy_write(struct mii_dev *bus, int addr, int devad, int reg, u16 value) { debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, value); return phywrite(bus->priv, addr, reg, value); } static int axi_emac_probe(struct udevice *dev) { struct axidma_plat *plat = dev_get_plat(dev); struct eth_pdata *pdata = &plat->eth_pdata; struct axidma_priv *priv = dev_get_priv(dev); int ret; priv->iobase = (struct axi_regs *)pdata->iobase; priv->dmatx = plat->dmatx; /* RX channel offset is 0x30 */ priv->dmarx = (struct axidma_reg *)((phys_addr_t)priv->dmatx + 0x30); priv->mactype = plat->mactype; if (priv->mactype == EMAC_1G) { priv->eth_hasnobuf = plat->eth_hasnobuf; priv->phyaddr = plat->phyaddr; priv->phy_of_handle = plat->phy_of_handle; priv->interface = pdata->phy_interface; if (IS_ENABLED(CONFIG_DM_ETH_PHY)) priv->bus = eth_phy_get_mdio_bus(dev); if (!priv->bus) { priv->bus = mdio_alloc(); priv->bus->read = axiemac_miiphy_read; priv->bus->write = axiemac_miiphy_write; priv->bus->priv = priv; ret = mdio_register_seq(priv->bus, dev_seq(dev)); if (ret) return ret; } if (IS_ENABLED(CONFIG_DM_ETH_PHY)) eth_phy_set_mdio_bus(dev, priv->bus); axiemac_phy_init(dev); } printf("AXI EMAC: %lx, phyaddr %d, interface %s\n", (ulong)pdata->iobase, priv->phyaddr, phy_string_for_interface(pdata->phy_interface)); return 0; } static int axi_emac_remove(struct udevice *dev) { struct axidma_priv *priv = dev_get_priv(dev); if (priv->mactype == EMAC_1G) { free(priv->phydev); mdio_unregister(priv->bus); mdio_free(priv->bus); } return 0; } static const struct eth_ops axi_emac_ops = { .start = axiemac_start, .send = axiemac_send, .recv = axiemac_recv, .free_pkt = axiemac_free_pkt, .stop = axiemac_stop, .write_hwaddr = axiemac_write_hwaddr, }; static int axi_emac_of_to_plat(struct udevice *dev) { struct axidma_plat *plat = dev_get_plat(dev); struct eth_pdata *pdata = &plat->eth_pdata; int node = dev_of_offset(dev); int offset = 0; pdata->iobase = dev_read_addr(dev); plat->mactype = dev_get_driver_data(dev); offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "axistream-connected"); if (offset <= 0) { printf("%s: axistream is not found\n", __func__); return -EINVAL; } plat->dmatx = (struct axidma_reg *)fdtdec_get_addr_size_auto_parent (gd->fdt_blob, 0, offset, "reg", 0, NULL, false); if (!plat->dmatx) { printf("%s: axi_dma register space not found\n", __func__); return -EINVAL; } if (plat->mactype == EMAC_1G) { plat->phyaddr = -1; offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "phy-handle"); if (offset > 0) { if (!(IS_ENABLED(CONFIG_DM_ETH_PHY))) plat->phyaddr = fdtdec_get_int(gd->fdt_blob, offset, "reg", -1); plat->phy_of_handle = offset; } pdata->phy_interface = dev_read_phy_mode(dev); if (pdata->phy_interface == PHY_INTERFACE_MODE_NA) return -EINVAL; plat->eth_hasnobuf = fdtdec_get_bool(gd->fdt_blob, node, "xlnx,eth-hasnobuf"); } return 0; } static const struct udevice_id axi_emac_ids[] = { { .compatible = "xlnx,axi-ethernet-1.00.a", .data = (uintptr_t)EMAC_1G }, { .compatible = "xlnx,xxv-ethernet-1.0", .data = (uintptr_t)EMAC_10G_25G }, { } }; U_BOOT_DRIVER(axi_emac) = { .name = "axi_emac", .id = UCLASS_ETH, .of_match = axi_emac_ids, .of_to_plat = axi_emac_of_to_plat, .probe = axi_emac_probe, .remove = axi_emac_remove, .ops = &axi_emac_ops, .priv_auto = sizeof(struct axidma_priv), .plat_auto = sizeof(struct axidma_plat), };