/* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2022 Marek Vasut */ #ifndef __IMX8MM_DATA_MODUL_EDM_SBC_H #define __IMX8MM_DATA_MODUL_EDM_SBC_H #include #include #include #define CONFIG_SYS_BOOTM_LEN SZ_128M #define CONFIG_SPL_MAX_SIZE (148 * 1024) #define CONFIG_SYS_MONITOR_LEN SZ_1M #define CONFIG_SPL_STACK 0x920000 #ifdef CONFIG_SPL_BUILD #define CONFIG_SPL_BSS_START_ADDR 0x910000 #define CONFIG_SPL_BSS_MAX_SIZE SZ_8K /* 8 kiB */ #define CONFIG_SYS_SPL_MALLOC_START 0x42200000 #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M /* 16 MiB */ #define CONFIG_MALLOC_F_ADDR 0x930000 /* For RAW image gives a error info not panic */ #define CONFIG_SPL_ABORT_ON_RAW_IMAGE #endif /* Link Definitions */ #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x200000 #define CONFIG_SYS_INIT_SP_OFFSET \ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) #define CONFIG_SYS_SDRAM_BASE 0x40000000 #define PHYS_SDRAM 0x40000000 #define PHYS_SDRAM_SIZE 0x40000000 /* Minimum 1 GiB DDR */ #define CONFIG_MXC_UART_BASE UART3_BASE_ADDR #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* PHY needs a longer autonegotiation timeout after reset */ #define PHY_ANEG_TIMEOUT 20000 /* USDHC */ #define CONFIG_SYS_FSL_USDHC_NUM 2 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 #if !defined(CONFIG_SPL_BUILD) #define CONFIG_EXTRA_ENV_SETTINGS \ "altbootcmd=setenv devpart 2 && run bootcmd ; reset\0" \ "bootlimit=3\0" \ "devtype=mmc\0" \ "devpart=1\0" \ /* Give slow devices beyond USB HUB chance to come up. */ \ "usb_pgood_delay=2000\0" \ "dfu_alt_info=" \ /* RAM block at DRAM offset 256..768 MiB */ \ "ram ram0=ram ram 0x50000000 0x20000000&" \ /* 16 MiB SPI NOR */ \ "mtd nor0=sf raw 0x0 0x1000000\0" \ "dmo_preboot=" \ "sf probe ; " /* Scan for SPI NOR, needed by DFU */ \ "run dmo_usb_start_hub ; " \ /* Attempt to start USB and Network console */ \ "run dmo_usb_cdc_acm_start ; " \ "run dmo_netconsole_start\0" \ "dmo_update_env=" \ "setenv dmo_update_env true ; saveenv ; saveenv\0" \ "dmo_usb_cdc_acm_start=" \ "if test \"${dmo_usb_cdc_acm_enabled}\" = \"true\" ; then "\ /* Ungate IMX8MM_CLK_USB1_CTRL_ROOT */ \ "mw 0x303844d0 3 ; " \ /* Read USBNC_n_PHY_STATUS BIT(4) VBUS_VLD */ \ "setexpr.l usbnc_n_phy_status *0x32e4023c \\\\& 0x8 ; " \ /* If USB OTG has valid VBUS, enable CDC ACM */ \ "if test \"${usbnc_n_phy_status}\" -eq 8 ; then "\ "usb start && " \ "setenv stderr ${stderr},usbacm && " \ "setenv stdout ${stdout},usbacm && " \ "setenv stdin ${stdin},usbacm ; " \ "fi ; " \ "fi\0" \ "dmo_usb_start_hub=" \ "i2c dev 1 ; " \ /* Reset the USB USB */ \ "gpio clear GPIO5_2 ; sleep 0.01 ; " /* t1 > 1us */ \ "gpio set GPIO5_2 ; sleep 0.01 ; " /* t5 > 3us */ \ /* Write chunks of descriptor into the USB HUB */ \ "mw.l 0x7e1000 0x14042417 ; mw.l 0x7e1004 0x9b0bb325 ; "\ "mw.l 0x7e1008 0x00000220 ; mw.l 0x7e100c 0x01320100 ; "\ "mw.l 0x7e1010 0x00003232 ; mw.l 0x7e1014 0x4d000909 ; "\ "i2c write 0x7e1000 0x2c 0x00 0x18 -s ; " \ "mw.l 0x7e1000 0x6300690f ; mw.l 0x7e1004 0x6f007200 ; "\ "mw.l 0x7e1008 0x68006300 ; mw.l 0x7e100c 0x70006900 ; "\ "i2c write 0x7e1000 0x2c 0x18 0x10 -s ; " \ "mw.l 0x7e1000 0x53005511 ; mw.l 0x7e1004 0x32004200 ; "\ "mw.l 0x7e1008 0x31003500 ; mw.l 0x7e100c 0x42003400 ; "\ "mw.l 0x7e1010 0x00006900 ; " \ "i2c write 0x7e1000 0x2c 0x54 0x12 -s ; " \ "mw.l 0x7e1000 0x00000101 ; " \ "i2c write 0x7e1000 0x2c 0xff 0x2 -s\0" \ "dmo_netconsole_start=" \ "if test \"${dmo_netconsole_enabled}\" = \"true\" ; then "\ "setenv autoload false && " \ "dhcp && " \ "setenv autoload && " \ "setenv ncip ${serverip} && " \ "setenv stderr ${stderr},nc && " \ "setenv stdout ${stdout},nc && " \ "setenv stdin ${stdin},nc ; " \ "fi" #endif #endif