// SPDX-License-Identifier: GPL-2.0+ /* dm9000.c: Version 1.2 12/15/2003 A Davicom DM9000 ISA NIC fast Ethernet driver for Linux. Copyright (C) 1997 Sten Wang (C)Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved. V0.11 06/20/2001 REG_0A bit3=1, default enable BP with DA match 06/22/2001 Support DM9801 progrmming E3: R25 = ((R24 + NF) & 0x00ff) | 0xf000 E4: R25 = ((R24 + NF) & 0x00ff) | 0xc200 R17 = (R17 & 0xfff0) | NF + 3 E5: R25 = ((R24 + NF - 3) & 0x00ff) | 0xc200 R17 = (R17 & 0xfff0) | NF v1.00 modify by simon 2001.9.5 change for kernel 2.4.x v1.1 11/09/2001 fix force mode bug v1.2 03/18/2003 Weilun Huang : Fixed phy reset. Added tx/rx 32 bit mode. Cleaned up for kernel merge. -------------------------------------- 12/15/2003 Initial port to u-boot by Sascha Hauer 06/03/2008 Remy Bohmer - Fixed the driver to work with DM9000A. (check on ISR receive status bit before reading the FIFO as described in DM9000 programming guide and application notes) - Added autodetect of databus width. - Made debug code compile again. - Adapt eth_send such that it matches the DM9000* application notes. Needed to make it work properly for DM9000A. - Adapted reset procedure to match DM9000 application notes (i.e. double reset) - some minor code cleanups These changes are tested with DM9000{A,EP,E} together with a 200MHz Atmel AT91SAM9261 core TODO: external MII is not functional, only internal at the moment. */ #include #include #include #include #include #include #include "dm9000x.h" /* Structure/enum declaration ------------------------------- */ typedef struct board_info { u32 runt_length_counter; /* counter: RX length < 64byte */ u32 long_length_counter; /* counter: RX length > 1514byte */ u32 reset_counter; /* counter: RESET */ u32 reset_tx_timeout; /* RESET caused by TX Timeout */ u32 reset_rx_status; /* RESET caused by RX Statsus wrong */ u16 tx_pkt_cnt; u16 queue_start_addr; u16 dbug_cnt; u8 phy_addr; u8 device_wait_reset; /* device state */ unsigned char srom[128]; void (*outblk)(volatile void *data_ptr, int count); void (*inblk)(void *data_ptr, int count); void (*rx_status)(u16 *rxstatus, u16 *rxlen); struct eth_device netdev; } board_info_t; static board_info_t dm9000_info; /* function declaration ------------------------------------- */ static int dm9000_probe(void); static u16 dm9000_phy_read(int); static void dm9000_phy_write(int, u16); static u8 dm9000_ior(int); static void dm9000_iow(int reg, u8 value); /* DM9000 network board routine ---------------------------- */ #ifndef CONFIG_DM9000_BYTE_SWAPPED #define dm9000_outb(d,r) writeb(d, (volatile u8 *)(r)) #define dm9000_outw(d,r) writew(d, (volatile u16 *)(r)) #define dm9000_outl(d,r) writel(d, (volatile u32 *)(r)) #define dm9000_inb(r) readb((volatile u8 *)(r)) #define dm9000_inw(r) readw((volatile u16 *)(r)) #define dm9000_inl(r) readl((volatile u32 *)(r)) #else #define dm9000_outb(d, r) __raw_writeb(d, r) #define dm9000_outw(d, r) __raw_writew(d, r) #define dm9000_outl(d, r) __raw_writel(d, r) #define dm9000_inb(r) __raw_readb(r) #define dm9000_inw(r) __raw_readw(r) #define dm9000_inl(r) __raw_readl(r) #endif #ifdef DEBUG static void dm9000_dump_packet(const char *func, u8 *packet, int length) { int i; printf("%s: length: %d\n", func, length); for (i = 0; i < length; i++) { if (i % 8 == 0) printf("\n%s: %02x: ", func, i); printf("%02x ", packet[i]); } printf("\n"); } #else static void dm9000_dump_packet(const char *func, u8 *packet, int length) {} #endif static void dm9000_outblk_8bit(volatile void *data_ptr, int count) { int i; for (i = 0; i < count; i++) dm9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA); } static void dm9000_outblk_16bit(volatile void *data_ptr, int count) { int i; u32 tmplen = (count + 1) / 2; for (i = 0; i < tmplen; i++) dm9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); } static void dm9000_outblk_32bit(volatile void *data_ptr, int count) { int i; u32 tmplen = (count + 3) / 4; for (i = 0; i < tmplen; i++) dm9000_outl(((u32 *) data_ptr)[i], DM9000_DATA); } static void dm9000_inblk_8bit(void *data_ptr, int count) { int i; for (i = 0; i < count; i++) ((u8 *) data_ptr)[i] = dm9000_inb(DM9000_DATA); } static void dm9000_inblk_16bit(void *data_ptr, int count) { int i; u32 tmplen = (count + 1) / 2; for (i = 0; i < tmplen; i++) ((u16 *) data_ptr)[i] = dm9000_inw(DM9000_DATA); } static void dm9000_inblk_32bit(void *data_ptr, int count) { int i; u32 tmplen = (count + 3) / 4; for (i = 0; i < tmplen; i++) ((u32 *) data_ptr)[i] = dm9000_inl(DM9000_DATA); } static void dm9000_rx_status_32bit(u16 *rxstatus, u16 *rxlen) { u32 tmpdata; dm9000_outb(DM9000_MRCMD, DM9000_IO); tmpdata = dm9000_inl(DM9000_DATA); *rxstatus = __le16_to_cpu(tmpdata); *rxlen = __le16_to_cpu(tmpdata >> 16); } static void dm9000_rx_status_16bit(u16 *rxstatus, u16 *rxlen) { dm9000_outb(DM9000_MRCMD, DM9000_IO); *rxstatus = __le16_to_cpu(dm9000_inw(DM9000_DATA)); *rxlen = __le16_to_cpu(dm9000_inw(DM9000_DATA)); } static void dm9000_rx_status_8bit(u16 *rxstatus, u16 *rxlen) { dm9000_outb(DM9000_MRCMD, DM9000_IO); *rxstatus = __le16_to_cpu(dm9000_inb(DM9000_DATA) + (dm9000_inb(DM9000_DATA) << 8)); *rxlen = __le16_to_cpu(dm9000_inb(DM9000_DATA) + (dm9000_inb(DM9000_DATA) << 8)); } /* Search DM9000 board, allocate space and register it */ int dm9000_probe(void) { u32 id_val; id_val = dm9000_ior(DM9000_VIDL); id_val |= dm9000_ior(DM9000_VIDH) << 8; id_val |= dm9000_ior(DM9000_PIDL) << 16; id_val |= dm9000_ior(DM9000_PIDH) << 24; if (id_val == DM9000_ID) { printf("dm9000 i/o: 0x%x, id: 0x%x \n", CONFIG_DM9000_BASE, id_val); return 0; } else { printf("dm9000 not found at 0x%08x id: 0x%08x\n", CONFIG_DM9000_BASE, id_val); return -1; } } /* General Purpose dm9000 reset routine */ static void dm9000_reset(void) { debug("resetting DM9000\n"); /* Reset DM9000, see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */ /* DEBUG: Make all GPIO0 outputs, all others inputs */ dm9000_iow(DM9000_GPCR, GPCR_GPIO0_OUT); /* Step 1: Power internal PHY by writing 0 to GPIO0 pin */ dm9000_iow(DM9000_GPR, 0); /* Step 2: Software reset */ dm9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); do { debug("resetting the DM9000, 1st reset\n"); udelay(25); /* Wait at least 20 us */ } while (dm9000_ior(DM9000_NCR) & 1); dm9000_iow(DM9000_NCR, 0); dm9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); /* Issue a second reset */ do { debug("resetting the DM9000, 2nd reset\n"); udelay(25); /* Wait at least 20 us */ } while (dm9000_ior(DM9000_NCR) & 1); /* Check whether the ethernet controller is present */ if ((dm9000_ior(DM9000_PIDL) != 0x0) || (dm9000_ior(DM9000_PIDH) != 0x90)) printf("ERROR: resetting DM9000 -> not responding\n"); } /* Initialize dm9000 board */ static int dm9000_init(struct eth_device *dev, struct bd_info *bd) { int i, oft, lnk; u8 io_mode; struct board_info *db = &dm9000_info; debug("%s\n", __func__); /* RESET device */ dm9000_reset(); if (dm9000_probe() < 0) return -1; /* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */ io_mode = dm9000_ior(DM9000_ISR) >> 6; switch (io_mode) { case 0x0: /* 16-bit mode */ printf("DM9000: running in 16 bit mode\n"); db->outblk = dm9000_outblk_16bit; db->inblk = dm9000_inblk_16bit; db->rx_status = dm9000_rx_status_16bit; break; case 0x01: /* 32-bit mode */ printf("DM9000: running in 32 bit mode\n"); db->outblk = dm9000_outblk_32bit; db->inblk = dm9000_inblk_32bit; db->rx_status = dm9000_rx_status_32bit; break; case 0x02: /* 8 bit mode */ printf("DM9000: running in 8 bit mode\n"); db->outblk = dm9000_outblk_8bit; db->inblk = dm9000_inblk_8bit; db->rx_status = dm9000_rx_status_8bit; break; default: /* Assume 8 bit mode, will probably not work anyway */ printf("DM9000: Undefined IO-mode:0x%x\n", io_mode); db->outblk = dm9000_outblk_8bit; db->inblk = dm9000_inblk_8bit; db->rx_status = dm9000_rx_status_8bit; break; } /* Program operating register, only internal phy supported */ dm9000_iow(DM9000_NCR, 0x0); /* TX Polling clear */ dm9000_iow(DM9000_TCR, 0); /* Less 3Kb, 200us */ dm9000_iow(DM9000_BPTR, BPTR_BPHW(3) | BPTR_JPT_600US); /* Flow Control : High/Low Water */ dm9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); /* SH FIXME: This looks strange! Flow Control */ dm9000_iow(DM9000_FCR, 0x0); /* Special Mode */ dm9000_iow(DM9000_SMCR, 0); /* clear TX status */ dm9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); /* Clear interrupt status */ dm9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS); printf("MAC: %pM\n", dev->enetaddr); if (!is_valid_ethaddr(dev->enetaddr)) { printf("WARNING: Bad MAC address (uninitialized EEPROM?)\n"); } /* fill device MAC address registers */ for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++) dm9000_iow(oft, dev->enetaddr[i]); for (i = 0, oft = 0x16; i < 8; i++, oft++) dm9000_iow(oft, 0xff); /* read back mac, just to be sure */ for (i = 0, oft = 0x10; i < 6; i++, oft++) debug("%02x:", dm9000_ior(oft)); debug("\n"); /* Activate DM9000 */ /* RX enable */ dm9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); /* Enable TX/RX interrupt mask */ dm9000_iow(DM9000_IMR, IMR_PAR); i = 0; while (!(dm9000_phy_read(1) & 0x20)) { /* autonegation complete bit */ udelay(1000); i++; if (i == 10000) { printf("could not establish link\n"); return 0; } } /* see what we've got */ lnk = dm9000_phy_read(17) >> 12; printf("operating at "); switch (lnk) { case 1: printf("10M half duplex "); break; case 2: printf("10M full duplex "); break; case 4: printf("100M half duplex "); break; case 8: printf("100M full duplex "); break; default: printf("unknown: %d ", lnk); break; } printf("mode\n"); return 0; } /* Hardware start transmission. Send a packet to media from the upper layer. */ static int dm9000_send(struct eth_device *netdev, void *packet, int length) { int tmo; struct board_info *db = &dm9000_info; dm9000_dump_packet(__func__ , packet, length); dm9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ /* Move data to DM9000 TX RAM */ dm9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */ /* push the data to the TX-fifo */ (db->outblk)(packet, length); /* Set TX length to DM9000 */ dm9000_iow(DM9000_TXPLL, length & 0xff); dm9000_iow(DM9000_TXPLH, (length >> 8) & 0xff); /* Issue TX polling command */ dm9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ /* wait for end of transmission */ tmo = get_timer(0) + 5 * CONFIG_SYS_HZ; while ( !(dm9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) || !(dm9000_ior(DM9000_ISR) & IMR_PTM) ) { if (get_timer(0) >= tmo) { printf("transmission timeout\n"); break; } } dm9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ debug("transmit done\n\n"); return 0; } /* Stop the interface. The interface is stopped when it is brought. */ static void dm9000_halt(struct eth_device *netdev) { debug("%s\n", __func__); /* RESET devie */ dm9000_phy_write(0, 0x8000); /* PHY RESET */ dm9000_iow(DM9000_GPR, 0x01); /* Power-Down PHY */ dm9000_iow(DM9000_IMR, 0x80); /* Disable all interrupt */ dm9000_iow(DM9000_RCR, 0x00); /* Disable RX */ } /* Received a packet and pass to upper layer */ static int dm9000_rx(struct eth_device *netdev) { u8 rxbyte; u8 *rdptr = (u8 *)net_rx_packets[0]; u16 rxstatus, rxlen = 0; struct board_info *db = &dm9000_info; /* Check packet ready or not, we must check the ISR status first for DM9000A */ if (!(dm9000_ior(DM9000_ISR) & 0x01)) /* Rx-ISR bit must be set. */ return 0; dm9000_iow(DM9000_ISR, 0x01); /* clear PR status latched in bit 0 */ /* There is _at least_ 1 package in the fifo, read them all */ for (;;) { dm9000_ior(DM9000_MRCMDX); /* Dummy read */ /* Get most updated data, only look at bits 0:1, See application notes DM9000 */ rxbyte = dm9000_inb(DM9000_DATA) & 0x03; /* Status check: this byte must be 0 or 1 */ if (rxbyte > DM9000_PKT_RDY) { dm9000_iow(DM9000_RCR, 0x00); /* Stop Device */ dm9000_iow(DM9000_ISR, 0x80); /* Stop INT request */ printf("DM9000 error: status check fail: 0x%x\n", rxbyte); return 0; } if (rxbyte != DM9000_PKT_RDY) return 0; /* No packet received, ignore */ debug("receiving packet\n"); /* A packet ready now & Get status/length */ (db->rx_status)(&rxstatus, &rxlen); debug("rx status: 0x%04x rx len: %d\n", rxstatus, rxlen); /* Move data from DM9000 */ /* Read received packet from RX SRAM */ (db->inblk)(rdptr, rxlen); if ((rxstatus & 0xbf00) || (rxlen < 0x40) || (rxlen > DM9000_PKT_MAX)) { if (rxstatus & 0x100) { printf("rx fifo error\n"); } if (rxstatus & 0x200) { printf("rx crc error\n"); } if (rxstatus & 0x8000) { printf("rx length error\n"); } if (rxlen > DM9000_PKT_MAX) { printf("rx length too big\n"); dm9000_reset(); } } else { dm9000_dump_packet(__func__ , rdptr, rxlen); debug("passing packet to upper layer\n"); net_process_received_packet(net_rx_packets[0], rxlen); } } return 0; } /* Read a word data from SROM */ #if !defined(CONFIG_DM9000_NO_SROM) void dm9000_read_srom_word(int offset, u8 *to) { dm9000_iow(DM9000_EPAR, offset); dm9000_iow(DM9000_EPCR, 0x4); udelay(8000); dm9000_iow(DM9000_EPCR, 0x0); to[0] = dm9000_ior(DM9000_EPDRL); to[1] = dm9000_ior(DM9000_EPDRH); } void dm9000_write_srom_word(int offset, u16 val) { dm9000_iow(DM9000_EPAR, offset); dm9000_iow(DM9000_EPDRH, ((val >> 8) & 0xff)); dm9000_iow(DM9000_EPDRL, (val & 0xff)); dm9000_iow(DM9000_EPCR, 0x12); udelay(8000); dm9000_iow(DM9000_EPCR, 0); } #endif static void dm9000_get_enetaddr(struct eth_device *dev) { #if !defined(CONFIG_DM9000_NO_SROM) int i; for (i = 0; i < 3; i++) dm9000_read_srom_word(i, dev->enetaddr + (2 * i)); #endif } /* Read a byte from I/O port */ static u8 dm9000_ior(int reg) { dm9000_outb(reg, DM9000_IO); return dm9000_inb(DM9000_DATA); } /* Write a byte to I/O port */ static void dm9000_iow(int reg, u8 value) { dm9000_outb(reg, DM9000_IO); dm9000_outb(value, DM9000_DATA); } /* Read a word from phyxcer */ static u16 dm9000_phy_read(int reg) { u16 val; /* Fill the phyxcer register into REG_0C */ dm9000_iow(DM9000_EPAR, DM9000_PHY | reg); dm9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */ udelay(100); /* Wait read complete */ dm9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */ val = (dm9000_ior(DM9000_EPDRH) << 8) | dm9000_ior(DM9000_EPDRL); /* The read data keeps on REG_0D & REG_0E */ debug("dm9000_phy_read(0x%x): 0x%x\n", reg, val); return val; } /* Write a word to phyxcer */ static void dm9000_phy_write(int reg, u16 value) { /* Fill the phyxcer register into REG_0C */ dm9000_iow(DM9000_EPAR, DM9000_PHY | reg); /* Fill the written data into REG_0D & REG_0E */ dm9000_iow(DM9000_EPDRL, (value & 0xff)); dm9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff)); dm9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */ udelay(500); /* Wait write complete */ dm9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ debug("dm9000_phy_write(reg:0x%x, value:0x%x)\n", reg, value); } int dm9000_initialize(struct bd_info *bis) { struct eth_device *dev = &(dm9000_info.netdev); /* Load MAC address from EEPROM */ dm9000_get_enetaddr(dev); dev->init = dm9000_init; dev->halt = dm9000_halt; dev->send = dm9000_send; dev->recv = dm9000_rx; strcpy(dev->name, "dm9000"); eth_register(dev); return 0; }