/* * Copyright 2011-2012 Freescale Semiconductor, Inc. * * SPDX-License-Identifier: GPL-2.0+ */ /* * Corenet DS style board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_pbi.cfg #define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg #endif #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE /* Set 1M boot space */ #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #define CONFIG_SYS_NO_FLASH #endif #define CONFIG_CMD_REGINFO /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ #define CONFIG_E500MC /* BOOKE e500mc family */ #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ #define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ #define CONFIG_MP /* support multiple processors */ #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xeff80000 #endif #ifndef CONFIG_RESET_VECTOR_ADDRESS #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc #endif #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS #define CONFIG_FSL_IFC /* Enable IFC Support */ #define CONFIG_PCI /* Enable PCI/PCIE */ #define CONFIG_PCIE1 /* PCIE controler 1 */ #define CONFIG_PCIE2 /* PCIE controler 2 */ #define CONFIG_PCIE3 /* PCIE controler 3 */ #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ #define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) #define CONFIG_ENV_IS_NOWHERE #endif #else #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #endif #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 #define CONFIG_ENV_SPI_MAX_HZ 10000000 #define CONFIG_ENV_SPI_MODE 0 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 #elif defined(CONFIG_SDCARD) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_OFFSET (512 * 1097) #elif defined(CONFIG_NAND) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) #define CONFIG_ENV_IS_IN_REMOTE #define CONFIG_ENV_ADDR 0xffe20000 #define CONFIG_ENV_SIZE 0x2000 #elif defined(CONFIG_ENV_IS_NOWHERE) #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() #ifndef __ASSEMBLY__ unsigned long get_board_sys_clk(void); unsigned long get_board_ddr_clk(void); #endif /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_SYS_CACHE_STASHING #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_DDR_ECC #ifdef CONFIG_DDR_ECC #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_MEM_INIT_VALUE 0xdeadbeef #endif #define CONFIG_ENABLE_36BIT_PHYS #ifdef CONFIG_PHYS_64BIT #define CONFIG_ADDR_MAP #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ #endif #if 0 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ #endif #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00400000 #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* * Config the L3 Cache as L3 SRAM */ #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull #endif /* EEPROM */ #define CONFIG_ID_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* * DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */ #define CONFIG_DIMM_SLOTS_PER_CTLR 2 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 #define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE #define CONFIG_DDR_SPD #define CONFIG_FSL_DDR3 #define CONFIG_SYS_SPD_BUS_NUM 0 #define SPD_EEPROM_ADDRESS1 0x51 #define SPD_EEPROM_ADDRESS2 0x52 #define SPD_EEPROM_ADDRESS3 0x53 #define SPD_EEPROM_ADDRESS4 0x54 #define SPD_EEPROM_ADDRESS5 0x55 #define SPD_EEPROM_ADDRESS6 0x56 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ /* * IFC Definitions */ #define CONFIG_SYS_FLASH_BASE 0xe0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) #else #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE #endif #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ + 0x8000000) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) /* NOR Flash Timing Params */ #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ FTIM0_NOR_TEADC(0x5) | \ FTIM0_NOR_TEAHC(0x5)) #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ FTIM1_NOR_TRAD_NOR(0x1A) |\ FTIM1_NOR_TSEQRAD_NOR(0x13)) #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ FTIM2_NOR_TCH(0x4) | \ FTIM2_NOR_TWPH(0x0E) | \ FTIM2_NOR_TWP(0x1c)) #define CONFIG_SYS_NOR_FTIM3 0x0 #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} #define CONFIG_FSL_QIXIS /* use common QIXIS code */ #define QIXIS_BASE 0xffdf0000 #define QIXIS_LBMAP_SWITCH 6 #define QIXIS_LBMAP_MASK 0x0f #define QIXIS_LBMAP_SHIFT 0 #define QIXIS_LBMAP_DFLTBANK 0x00 #define QIXIS_LBMAP_ALTBANK 0x04 #define QIXIS_RST_CTL_RESET 0x83 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 #ifdef CONFIG_PHYS_64BIT #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) #else #define QIXIS_BASE_PHYS QIXIS_BASE #endif #define CONFIG_SYS_CSPR3_EXT (0xf) #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ | CSPR_V) #define CONFIG_SYS_AMASK3 IFC_AMASK(4 * 1024) #define CONFIG_SYS_CSOR3 0x0 /* QIXIS Timing parameters for IFC CS3 */ #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ FTIM0_GPCM_TEADC(0x0e) | \ FTIM0_GPCM_TEAHC(0x0e)) #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ FTIM1_GPCM_TRAD(0x3f)) #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ FTIM2_GPCM_TCH(0x0) | \ FTIM2_GPCM_TWP(0x1f)) #define CONFIG_SYS_CS3_FTIM3 0x0 /* NAND Flash on IFC */ #define CONFIG_NAND_FSL_IFC #define CONFIG_SYS_NAND_BASE 0xff800000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) #else #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE #endif #define CONFIG_SYS_NAND_CSPR_EXT (0xf) #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ | CSPR_MSEL_NAND /* MSEL = NAND */ \ | CSPR_V) #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ #define CONFIG_SYS_NAND_ONFI_DETECTION /* ONFI NAND Flash mode0 Timing Params */ #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ FTIM0_NAND_TWP(0x18) | \ FTIM0_NAND_TWCHT(0x07) | \ FTIM0_NAND_TWH(0x0a)) #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ FTIM1_NAND_TWBE(0x39) | \ FTIM1_NAND_TRR(0x0e) | \ FTIM1_NAND_TRP(0x18)) #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ FTIM2_NAND_TREH(0x0a) | \ FTIM2_NAND_TWHRE(0x1e)) #define CONFIG_SYS_NAND_FTIM3 0x0 #define CONFIG_SYS_NAND_DDR_LAW 11 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) #if defined(CONFIG_NAND) #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 #else #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 #endif #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #if defined(CONFIG_RAMBOOT_PBL) #define CONFIG_SYS_RAMBOOT #endif #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ #define CONFIG_MISC_INIT_R #define CONFIG_HWCONFIG /* define to use L1 as initial stack */ #define CONFIG_L1_INIT_RAM #define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 /* The assembler doesn't like typecast */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) #else #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe0ec000 /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS #endif #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (512 * 1024) #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT #define CONFIG_OF_BOARD_SETUP #define CONFIG_OF_STDOUT_VIA_ALIAS /* new uImage format support */ #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 100000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ #define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ #define I2C_MUX_CH_DEFAULT 0x8 #define I2C_MUX_CH_VOL_MONITOR 0xa #define I2C_MUX_CH_VSC3316_FS 0xc #define I2C_MUX_CH_VSC3316_BS 0xd /* Voltage monitor on channel 2*/ #define I2C_VOL_MONITOR_ADDR 0x40 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 /* VSC Crossbar switches */ #define CONFIG_VSC_CROSSBAR #define VSC3316_FSM_TX_ADDR 0x70 #define VSC3316_FSM_RX_ADDR 0x71 /* * RapidIO */ #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull #else #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 #endif #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull #else #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 #endif #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ /* * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ /* slave core release by master*/ #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ /* * SRIO_PCIE_BOOT - SLAVE */ #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) #endif /* * eSPI - Enhanced SPI */ #define CONFIG_FSL_ESPI #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_SST #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE 0 /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* controller 1, direct to uli, tgtid 3, Base address 20000 */ #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull #else #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 #endif #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull #else #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 #endif #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ /* controller 2, Slot 2, tgtid 2, Base address 201000 */ #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull #else #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 #endif #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull #else #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 #endif #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 3, Slot 1, tgtid 1, Base address 202000 */ #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull #else #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 #endif #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull #else #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 #endif #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ /* controller 4, Base address 203000 */ #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull #define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ /* Qman/Bman */ #ifndef CONFIG_NOBQFMAN #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ #define CONFIG_SYS_BMAN_NUM_PORTALS 50 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull #else #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE #endif #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 #define CONFIG_SYS_QMAN_NUM_PORTALS 50 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 #ifdef CONFIG_PHYS_64BIT #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull #else #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE #endif #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 #define CONFIG_SYS_DPAA_FMAN #define CONFIG_SYS_DPAA_PME #define CONFIG_SYS_PMAN #define CONFIG_SYS_DPAA_DCE #define CONFIG_SYS_INTERLAKEN /* Default address of microcode for the Linux Fman driver */ #if defined(CONFIG_SPIFLASH) /* * env is stored at 0x100000, sector size is 0x10000, ucode is stored after * env, so we got 0x110000. */ #define CONFIG_SYS_QE_FW_IN_SPIFLASH #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 #elif defined(CONFIG_SDCARD) /* * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is * about 545KB (1089 blocks), Env is stored after the image, and the env size is * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. */ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC #define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130) #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) /* * Slave has no ucode locally, it can fetch this from remote. When implementing * in two corenet boards, slave's ucode could be stored in master's memory * space, the address can be mapped from slave TLB->slave LAW-> * slave SRIO or PCIE outbound window->master inbound window-> * master LAW->the ucode address in master's memory space. */ #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 #endif #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #endif /* CONFIG_NOBQFMAN */ #ifdef CONFIG_SYS_DPAA_FMAN #define CONFIG_FMAN_ENET #define CONFIG_PHYLIB_10G #define CONFIG_PHY_VITESSE #define CONFIG_PHY_TERANETICS #define SGMII_CARD_PORT1_PHY_ADDR 0x1C #define SGMII_CARD_PORT2_PHY_ADDR 0x1D #define SGMII_CARD_PORT3_PHY_ADDR 0x1E #define SGMII_CARD_PORT4_PHY_ADDR 0x1F #define FM1_10GEC1_PHY_ADDR 0x0 #define FM1_10GEC2_PHY_ADDR 0x1 #define FM2_10GEC1_PHY_ADDR 0x2 #define FM2_10GEC2_PHY_ADDR 0x3 #endif #ifdef CONFIG_PCI #define CONFIG_PCI_INDIRECT_BRIDGE #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_E1000 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_DOS_PARTITION #endif /* CONFIG_PCI */ /* SATA */ #ifdef CONFIG_FSL_SATA_V2 #define CONFIG_LIBATA #define CONFIG_FSL_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_SATA1 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA #define CONFIG_SATA2 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA #define CONFIG_LBA48 #define CONFIG_CMD_SATA #define CONFIG_DOS_PARTITION #define CONFIG_CMD_EXT2 #endif #ifdef CONFIG_FMAN_ENET #define CONFIG_MII /* MII PHY management */ #define CONFIG_ETHPRIME "FM1@DTSEC1" #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif /* * Environment */ #define CONFIG_LOADS_ECHO /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_DHCP #define CONFIG_CMD_ELF #define CONFIG_CMD_ERRATA #define CONFIG_CMD_GREPENV #define CONFIG_CMD_IRQ #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_CMD_SETEXPR #ifdef CONFIG_PCI #define CONFIG_CMD_PCI #define CONFIG_CMD_NET #endif /* * USB */ #define CONFIG_CMD_USB #define CONFIG_USB_STORAGE #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_FSL #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_CMD_EXT2 #define CONFIG_HAS_FSL_DR_USB #define CONFIG_MMC #ifdef CONFIG_MMC #define CONFIG_FSL_ESDHC #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT #define CONFIG_CMD_MMC #define CONFIG_GENERIC_MMC #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION #endif /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #ifdef CONFIG_CMD_KGDB #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/ /* * For booting Linux, the board info and command line data * have to be in the first 64 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ #ifdef CONFIG_CMD_KGDB #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ #define CONFIG_ROOTPATH "/opt/nfsroot" #define CONFIG_BOOTFILE "uImage" #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ /* default location for tftp and bootm */ #define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ #define CONFIG_BAUDRATE 115200 #define __USB_PHY_TYPE utmi /* * T4240 has 3 DDR controllers. Default to 3way_4KB interleaving. It can be * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to * cacheline interleaving. It can be cacheline, page, bank, superbank. * See doc/README.fsl-ddr for details. */ #ifdef CONFIG_PPC_T4240 #define CTRL_INTLV_PREFERED 3way_4KB #else #define CTRL_INTLV_PREFERED cacheline #endif #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:" \ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ "bank_intlv=auto;" \ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ "tftpflash=tftpboot $loadaddr $uboot && " \ "protect off $ubootaddr +$filesize && " \ "erase $ubootaddr +$filesize && " \ "cp.b $loadaddr $ubootaddr $filesize && " \ "protect on $ubootaddr +$filesize && " \ "cmp.b $loadaddr $ubootaddr $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=t4240qds/ramdisk.uboot\0" \ "fdtaddr=c00000\0" \ "fdtfile=t4240qds/t4240qds.dtb\0" \ "bdev=sda3\0" \ "c=ffe\0" /* For emulation this causes u-boot to jump to the start of the proof point app code automatically */ #define CONFIG_PROOF_POINTS \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "cpu 1 release 0x29000000 - - -;" \ "cpu 2 release 0x29000000 - - -;" \ "cpu 3 release 0x29000000 - - -;" \ "cpu 4 release 0x29000000 - - -;" \ "cpu 5 release 0x29000000 - - -;" \ "cpu 6 release 0x29000000 - - -;" \ "cpu 7 release 0x29000000 - - -;" \ "go 0x29000000" #define CONFIG_HVBOOT \ "setenv bootargs config-addr=0x60000000; " \ "bootm 0x01000000 - 0x00f00000" #define CONFIG_ALU \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "cpu 1 release 0x01000000 - - -;" \ "cpu 2 release 0x01000000 - - -;" \ "cpu 3 release 0x01000000 - - -;" \ "cpu 4 release 0x01000000 - - -;" \ "cpu 5 release 0x01000000 - - -;" \ "cpu 6 release 0x01000000 - - -;" \ "cpu 7 release 0x01000000 - - -;" \ "go 0x01000000" #define CONFIG_LINUX \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "setenv ramdiskaddr 0x02000000;" \ "setenv fdtaddr 0x00c00000;" \ "setenv loadaddr 0x1000000;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_HDBOOT \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_LINUX #ifdef CONFIG_SECURE_BOOT #include <asm/fsl_secure_boot.h> #endif #endif /* __CONFIG_H */