/* SPDX-License-Identifier: GPL-2.0+ */ /* * Configuration settings for the Sentec Cobra Board. * * (C) Copyright 2003 Josef Baumgartner */ /* * configuration for ASTRO "Urmel" board. * Originating from Cobra5272 configuration, messed up by * Wolfgang Wegner * Please do not bother the original author with bug reports * concerning this file. */ #ifndef _CONFIG_ASTRO_MCF5373L_H #define _CONFIG_ASTRO_MCF5373L_H #include /* * set the card type to actually compile for; either of * the possibilities listed below has to be used! */ #define ASTRO_V532 1 #if ASTRO_V532 #define ASTRO_ID 0xF8 #elif ASTRO_V512 #define ASTRO_ID 0xFA #elif ASTRO_TWIN7S2 #define ASTRO_ID 0xF9 #elif ASTRO_V912 #define ASTRO_ID 0xFC #elif ASTRO_COFDMDUOS2 #define ASTRO_ID 0xFB #else #error No card type defined! #endif /* * CONFIG_RAM defines if u-boot is loaded via BDM (or started from * a different bootloader that has already performed RAM setup) or * started directly from flash, which is the regular case for production * boards. */ #ifdef CONFIG_RAM #define CONFIG_MONITOR_IS_IN_RAM #define ENABLE_JFFS 0 #else #define ENABLE_JFFS 1 #endif /* I2C */ /* * Defines processor clock - important for correct timings concerning serial * interface etc. */ #define CONFIG_SYS_CLK 80000000 #define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3) #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ #define CONFIG_SYS_CORE_SRAM_SIZE 0x8000 #define CONFIG_SYS_CORE_SRAM 0x80000000 #define CONFIG_SYS_UNIFY_CACHE /* * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected * in u-boot command interface */ #define CONFIG_SYS_UART_PORT (2) #define CONFIG_SYS_UART2_ALT3_GPIO /* * Watchdog configuration; Watchdog is disabled for running from RAM * and set to highest possible value else. Beware there is no check * in the watchdog code to validate the timeout value set here! */ #ifndef CONFIG_MONITOR_IS_IN_RAM #define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */ #endif /* * Configuration for environment * Environment is located in the last sector of the flash */ #ifndef CONFIG_MONITOR_IS_IN_RAM #else /* * environment in RAM - This is used to use a single PC-based application * to load an image, load U-Boot, load an environment and then start U-Boot * to execute the commands from the environment. Feedback is done via setting * and reading memory locations. */ #endif /* here we put our FPGA configuration... */ /* Define user parameters that have to be customized most likely */ /* AUTOBOOT settings - booting images automatically by u-boot after power on */ /* * The following settings will be contained in the environment block ; if you * want to use a neutral environment all those settings can be manually set in * u-boot: 'set' command */ #define CONFIG_EXTRA_ENV_SETTINGS \ "loaderversion=11\0" \ "card_id="__stringify(ASTRO_ID)"\0" \ "alterafile=0\0" \ "xilinxfile=0\0" \ "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ "fpga load 0 0x41000000 $filesize\0" \ "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ "fpga load 1 0x41000000 $filesize\0" \ "env_default=1\0" \ "env_check=if test $env_default -eq 1;"\ " then setenv env_default 0;saveenv;fi\0" /* * "update" is a non-standard command that has to be supplied * by external update.c; This is not included in mainline because * it needs non-blocking CFI routines. */ #define CONFIG_FPGA_COUNT 1 #define CONFIG_SYS_FPGA_PROG_FEEDBACK #define CONFIG_SYS_FPGA_WAIT 1000 /* End of user parameters to be customized */ /* Defines memory range for test */ /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /* Base register address */ #define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */ /* System Conf. Reg. & System Protection Reg. */ #define CONFIG_SYS_SCR 0x0003; #define CONFIG_SYS_SPR 0xffff; /* * Definitions for initial stack pointer and data area (in internal SRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) /* * Start addresses for the final memory configuration * (Set up by the startup code) * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 */ #define CONFIG_SYS_SDRAM_BASE 0x40000000 /* * Chipselect bank definitions * * CS0 - Flash 32MB (first 16MB) * CS1 - Flash 32MB (second half) * CS2 - FPGA * CS3 - FPGA * CS4 - unused * CS5 - unused */ #define CONFIG_SYS_CS0_BASE 0 #define CONFIG_SYS_CS0_MASK 0x00ff0001 #define CONFIG_SYS_CS0_CTRL 0x00001fc0 #define CONFIG_SYS_CS1_BASE 0x01000000 #define CONFIG_SYS_CS1_MASK 0x00ff0001 #define CONFIG_SYS_CS1_CTRL 0x00001fc0 #define CONFIG_SYS_CS2_BASE 0x20000000 #define CONFIG_SYS_CS2_MASK 0x00ff0001 #define CONFIG_SYS_CS2_CTRL 0x0000fec0 #define CONFIG_SYS_CS3_BASE 0x21000000 #define CONFIG_SYS_CS3_MASK 0x00ff0001 #define CONFIG_SYS_CS3_CTRL 0x0000fec0 #define CONFIG_SYS_FLASH_BASE 0x00000000 /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ (CONFIG_SYS_SDRAM_SIZE << 20)) /* FLASH organization */ #define CONFIG_SYS_MAX_FLASH_SECT 259 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 #define CONFIG_SYS_FLASH_SIZE 0x2000000 #define CONFIG_SYS_FLASH_CFI_NONBLOCK 1 #define LDS_BOARD_TEXT \ . = DEFINED(env_offset) ? env_offset : .; \ env/embedded.o(.text*) #if ENABLE_JFFS /* JFFS Partition offset set */ #define CONFIG_SYS_JFFS2_FIRST_BANK 0 #define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* 512k reserved for u-boot */ #define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40 #endif /* Cache Configuration */ #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 8) #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 4) #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ CF_CACR_DCM_P) #endif /* _CONFIG_ASTRO_MCF5373L_H */