// SPDX-License-Identifier: GPL-2.0+ /* * dts file for Xilinx ZynqMP ZCU104 * * (C) Copyright 2017 - 2021, Xilinx, Inc. * * Michal Simek <michal.simek@amd.com> */ /dts-v1/; #include "zynqmp.dtsi" #include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/pinctrl/pinctrl-zynqmp.h> #include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU104 RevC"; compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp"; aliases { ethernet0 = &gem3; i2c0 = &i2c1; mmc0 = &sdhci1; nvmem0 = &eeprom; rtc0 = &rtc; serial0 = &uart0; serial1 = &uart1; serial2 = &dcc; spi0 = &qspi; usb0 = &usb0; }; chosen { bootargs = "earlycon"; stdout-path = "serial0:115200n8"; }; memory@0 { device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; ina226 { compatible = "iio-hwmon"; io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>; }; clock_8t49n287_5: clk125 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <125000000>; }; clock_8t49n287_2: clk26 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <26000000>; }; clock_8t49n287_3: clk27 { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <27000000>; }; }; &can1 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_can1_default>; }; &dcc { status = "okay"; }; &fpd_dma_chan1 { status = "okay"; }; &fpd_dma_chan2 { status = "okay"; }; &fpd_dma_chan3 { status = "okay"; }; &fpd_dma_chan4 { status = "okay"; }; &fpd_dma_chan5 { status = "okay"; }; &fpd_dma_chan6 { status = "okay"; }; &fpd_dma_chan7 { status = "okay"; }; &fpd_dma_chan8 { status = "okay"; }; &gem3 { status = "okay"; phy-handle = <&phy0>; phy-mode = "rgmii-id"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gem3_default>; mdio: mdio { #address-cells = <1>; #size-cells = <0>; phy0: ethernet-phy@c { #phy-cells = <1>; compatible = "ethernet-phy-id2000.a231"; reg = <0xc>; ti,rx-internal-delay = <0x8>; ti,tx-internal-delay = <0xa>; ti,fifo-depth = <0x1>; ti,dp83867-rxctrl-strap-quirk; reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; }; }; }; &gpio { status = "okay"; }; &gpu { status = "okay"; }; &i2c1 { status = "okay"; clock-frequency = <400000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1_default>; pinctrl-1 = <&pinctrl_i2c1_gpio>; scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; tca6416_u97: gpio@20 { compatible = "ti,tca6416"; reg = <0x20>; gpio-controller; #gpio-cells = <2>; /* * IRQ not connected * Lines: * 0 - IRPS5401_ALERT_B * 1 - HDMI_8T49N241_INT_ALM * 2 - MAX6643_OT_B * 3 - MAX6643_FANFAIL_B * 5 - IIC_MUX_RESET_B * 6 - GEM3_EXP_RESET_B * 7 - FMC_LPC_PRSNT_M2C_B * 4, 10 - 17 - not connected */ }; /* Another connection to this bus via PL i2c via PCA9306 - u45 */ i2c-mux@74 { /* u34 */ compatible = "nxp,pca9548"; #address-cells = <1>; #size-cells = <0>; reg = <0x74>; i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; /* * IIC_EEPROM 1kB memory which uses 256B blocks * where every block has different address. * 0 - 256B address 0x54 * 256B - 512B address 0x55 * 512B - 768B address 0x56 * 768B - 1024B address 0x57 */ eeprom: eeprom@54 { /* u23 */ compatible = "atmel,24c08"; reg = <0x54>; #address-cells = <1>; #size-cells = <1>; }; }; i2c@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>; /* 8T49N287 - u182 */ }; i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ compatible = "infineon,irps5401"; reg = <0x43>; /* pmbus / i2c 0x13 */ }; irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ compatible = "infineon,irps5401"; reg = <0x44>; /* pmbus / i2c 0x14 */ }; }; i2c@3 { #address-cells = <1>; #size-cells = <0>; reg = <3>; u183: ina226@40 { /* u183 */ compatible = "ti,ina226"; #io-channel-cells = <1>; reg = <0x40>; shunt-resistor = <5000>; }; }; i2c@5 { #address-cells = <1>; #size-cells = <0>; reg = <5>; }; i2c@7 { #address-cells = <1>; #size-cells = <0>; reg = <7>; }; /* 4, 6 not connected */ }; }; &pinctrl0 { status = "okay"; pinctrl_can1_default: can1-default { mux { function = "can1"; groups = "can1_6_grp"; }; conf { groups = "can1_6_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; conf-rx { pins = "MIO25"; bias-high-impedance; }; conf-tx { pins = "MIO24"; bias-disable; }; }; pinctrl_i2c1_default: i2c1-default { mux { groups = "i2c1_4_grp"; function = "i2c1"; }; conf { groups = "i2c1_4_grp"; bias-pull-up; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; }; pinctrl_i2c1_gpio: i2c1-gpio { mux { groups = "gpio0_16_grp", "gpio0_17_grp"; function = "gpio0"; }; conf { groups = "gpio0_16_grp", "gpio0_17_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; }; pinctrl_gem3_default: gem3-default { mux { function = "ethernet3"; groups = "ethernet3_0_grp"; }; conf { groups = "ethernet3_0_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; conf-rx { pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", "MIO75"; bias-high-impedance; low-power-disable; }; conf-tx { pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68", "MIO69"; bias-disable; low-power-enable; }; mux-mdio { function = "mdio3"; groups = "mdio3_0_grp"; }; conf-mdio { groups = "mdio3_0_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; bias-disable; }; }; pinctrl_sdhci1_default: sdhci1-default { mux { groups = "sdio1_0_grp"; function = "sdio1"; }; conf { groups = "sdio1_0_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; bias-disable; drive-strength = <12>; }; mux-cd { groups = "sdio1_cd_0_grp"; function = "sdio1_cd"; }; conf-cd { groups = "sdio1_cd_0_grp"; bias-high-impedance; bias-pull-up; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; }; }; pinctrl_uart0_default: uart0-default { mux { groups = "uart0_4_grp"; function = "uart0"; }; conf { groups = "uart0_4_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; conf-rx { pins = "MIO18"; bias-high-impedance; }; conf-tx { pins = "MIO19"; bias-disable; }; }; pinctrl_uart1_default: uart1-default { mux { groups = "uart1_5_grp"; function = "uart1"; }; conf { groups = "uart1_5_grp"; slew-rate = <SLEW_RATE_SLOW>; power-source = <IO_STANDARD_LVCMOS18>; drive-strength = <12>; }; conf-rx { pins = "MIO21"; bias-high-impedance; }; conf-tx { pins = "MIO20"; bias-disable; }; }; pinctrl_usb0_default: usb0-default { mux { groups = "usb0_0_grp"; function = "usb0"; }; conf { groups = "usb0_0_grp"; power-source = <IO_STANDARD_LVCMOS18>; }; conf-rx { pins = "MIO52", "MIO53", "MIO55"; bias-high-impedance; drive-strength = <12>; slew-rate = <SLEW_RATE_FAST>; }; conf-tx { pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", "MIO60", "MIO61", "MIO62", "MIO63"; bias-disable; drive-strength = <4>; slew-rate = <SLEW_RATE_SLOW>; }; }; }; &psgtr { status = "okay"; /* nc, sata, usb3, dp */ clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; clock-names = "ref1", "ref2", "ref3"; }; &qspi { status = "okay"; flash@0 { compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ #address-cells = <1>; #size-cells = <1>; reg = <0x0>; spi-tx-bus-width = <4>; spi-rx-bus-width = <4>; spi-max-frequency = <108000000>; /* Based on DC1 spec */ partition@0 { /* for testing purpose */ label = "qspi-fsbl-uboot"; reg = <0x0 0x100000>; }; partition@100000 { /* for testing purpose */ label = "qspi-linux"; reg = <0x100000 0x500000>; }; partition@600000 { /* for testing purpose */ label = "qspi-device-tree"; reg = <0x600000 0x20000>; }; partition@620000 { /* for testing purpose */ label = "qspi-rootfs"; reg = <0x620000 0x5E0000>; }; }; }; &rtc { status = "okay"; }; &sata { status = "okay"; /* SATA OOB timing settings */ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; phy-names = "sata-phy"; phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sdhci1_default>; xlnx,mio-bank = <1>; disable-wp; }; &uart0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0_default>; }; &uart1 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1_default>; }; /* ULPI SMSC USB3320 */ &usb0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usb0_default>; phy-names = "usb3-phy"; phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; }; &dwc3_0 { status = "okay"; dr_mode = "host"; snps,usb3_lpm_capable; maximum-speed = "super-speed"; }; &watchdog0 { status = "okay"; }; &xilinx_ams { status = "okay"; }; &ams_ps { status = "okay"; }; &ams_pl { status = "okay"; }; &zynqmp_dpdma { status = "okay"; }; &zynqmp_dpsub { status = "okay"; phy-names = "dp-phy0", "dp-phy1"; phys = <&psgtr 1 PHY_TYPE_DP 0 3>, <&psgtr 0 PHY_TYPE_DP 1 3>; };