/* * (C) Copyright 2000 - 2002 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ #include #include #include #include DECLARE_GLOBAL_DATA_PTR; int checkcpu (void) { unsigned int pvr = get_pvr (); unsigned int version = pvr >> 16; unsigned char revision; ulong clock = gd->cpu_clk; char buf[32]; puts ("CPU: "); switch (version) { case CPU_TYPE_8240: puts ("MPC8240"); break; case CPU_TYPE_8245: puts ("MPC8245"); break; default: return -1; /*not valid for this source */ } CONFIG_READ_BYTE (REVID, revision); if (revision) { printf (" Revision %d.%d", (revision & 0xf0) >> 4, (revision & 0x0f)); } else { return -1; /* no valid CPU revision info */ } printf (" at %s MHz: ", strmhz (buf, clock)); print_size(checkicache(), " I-Cache "); print_size(checkdcache(), " D-Cache\n"); return 0; } /* ------------------------------------------------------------------------- */ /* L1 i-cache */ int checkicache (void) { /*TODO*/ return 128 * 4 * 32; }; /* ------------------------------------------------------------------------- */ /* L1 d-cache */ int checkdcache (void) { /*TODO*/ return 128 * 4 * 32; }; /*------------------------------------------------------------------- */ int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { ulong msr, addr; /* Interrupts and MMU off */ __asm__ ("mtspr 81, 0"); /* Interrupts and MMU off */ __asm__ __volatile__ ("mfmsr %0":"=r" (msr):); msr &= ~0x1030; __asm__ __volatile__ ("mtmsr %0"::"r" (msr)); /* * Trying to execute the next instruction at a non-existing address * should cause a machine check, resulting in reset */ #ifdef CONFIG_SYS_RESET_ADDRESS addr = CONFIG_SYS_RESET_ADDRESS; #else /* * note: when CONFIG_SYS_MONITOR_BASE points to a RAM address, * CONFIG_SYS_MONITOR_BASE - sizeof (ulong) is usually a valid * address. Better pick an address known to be invalid on * your system and assign it to CONFIG_SYS_RESET_ADDRESS. * "(ulong)-1" used to be a good choice for many systems... */ addr = CONFIG_SYS_MONITOR_BASE - sizeof (ulong); #endif ((void (*)(void)) addr) (); return 1; } /* ------------------------------------------------------------------------- */ /* * Get timebase clock frequency (like cpu_clk in Hz) * This is the sys_logic_clk (memory bus) divided by 4 */ unsigned long get_tbclk (void) { return ((get_bus_freq (0) + 2L) / 4L); } /* ------------------------------------------------------------------------- */ /* * The MPC824x has an integrated PCI controller known as the MPC107. * The following are MPC107 Bridge Controller and PCI Support functions * */ /* * This procedure reads a 32-bit address MPC107 register, and returns * a 32 bit value. It swaps the address to little endian before * writing it to config address, and swaps the value to big endian * before returning to the caller. */ unsigned int mpc824x_mpc107_getreg (unsigned int regNum) { unsigned int temp; /* swap the addr. to little endian */ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum); temp = *(volatile unsigned int *) CHRP_REG_DATA; return PCISWAP (temp); /* swap the data upon return */ } /* * This procedure writes a 32-bit address MPC107 register. It swaps * the address to little endian before writing it to config address. */ void mpc824x_mpc107_setreg (unsigned int regNum, unsigned int regVal) { /* swap the addr. to little endian */ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum); *(volatile unsigned int *) CHRP_REG_DATA = PCISWAP (regVal); return; } /* * Write a byte (8 bits) to a memory location. */ void mpc824x_mpc107_write8 (unsigned int addr, unsigned char data) { *(unsigned char *) addr = data; __asm__ ("sync"); } /* * Write a word (16 bits) to a memory location after the value * has been byte swapped (big to little endian or vice versa) */ void mpc824x_mpc107_write16 (unsigned int address, unsigned short data) { *(volatile unsigned short *) address = BYTE_SWAP_16_BIT (data); __asm__ ("sync"); } /* * Write a long word (32 bits) to a memory location after the value * has been byte swapped (big to little endian or vice versa) */ void mpc824x_mpc107_write32 (unsigned int address, unsigned int data) { *(volatile unsigned int *) address = LONGSWAP (data); __asm__ ("sync"); } /* * Read a byte (8 bits) from a memory location. */ unsigned char mpc824x_mpc107_read8 (unsigned int addr) { return *(volatile unsigned char *) addr; } /* * Read a word (16 bits) from a memory location, and byte swap the * value before returning to the caller. */ unsigned short mpc824x_mpc107_read16 (unsigned int address) { unsigned short retVal; retVal = BYTE_SWAP_16_BIT (*(unsigned short *) address); return retVal; } /* * Read a long word (32 bits) from a memory location, and byte * swap the value before returning to the caller. */ unsigned int mpc824x_mpc107_read32 (unsigned int address) { unsigned int retVal; retVal = LONGSWAP (*(unsigned int *) address); return (retVal); } /* * Read a register in the Embedded Utilities Memory Block address * space. * Input: regNum - register number + utility base address. Example, * the base address of EPIC is 0x40000, the register number * being passed is 0x40000+the address of the target register. * (See epic.h for register addresses). * Output: The 32 bit little endian value of the register. */ unsigned int mpc824x_eummbar_read (unsigned int regNum) { unsigned int temp; temp = *(volatile unsigned int *) (EUMBBAR_VAL + regNum); temp = PCISWAP (temp); return temp; } /* * Write a value to a register in the Embedded Utilities Memory * Block address space. * Input: regNum - register number + utility base address. Example, * the base address of EPIC is 0x40000, the register * number is 0x40000+the address of the target register. * (See epic.h for register addresses). * regVal - value to be written to the register. */ void mpc824x_eummbar_write (unsigned int regNum, unsigned int regVal) { *(volatile unsigned int *) (EUMBBAR_VAL + regNum) = PCISWAP (regVal); return; } /* ------------------------------------------------------------------------- */