// SPDX-License-Identifier: GPL-2.0+ /* * (C) Copyright 2013 - 2022, Xilinx, Inc. * (C) Copyright 2022, Advanced Micro Devices, Inc. * * Xilinx Zynq SD Host Controller Interface */ #include #include #include #include #include #include "mmc_private.h" #include #include #include #include #include #include #include #include #include #include #include #include #include #define SDHCI_ARASAN_ITAPDLY_REGISTER 0xF0F8 #define SDHCI_ARASAN_ITAPDLY_SEL_MASK GENMASK(7, 0) #define SDHCI_ARASAN_OTAPDLY_REGISTER 0xF0FC #define SDHCI_ARASAN_OTAPDLY_SEL_MASK GENMASK(5, 0) #define SDHCI_ITAPDLY_CHGWIN BIT(9) #define SDHCI_ITAPDLY_ENABLE BIT(8) #define SDHCI_OTAPDLY_ENABLE BIT(6) #define SDHCI_TUNING_LOOP_COUNT 40 #define MMC_BANK2 0x2 #define SD_DLL_CTRL 0xFF180358 #define SD_ITAP_DLY 0xFF180314 #define SD_OTAP_DLY 0xFF180318 #define SD0_DLL_RST BIT(2) #define SD1_DLL_RST BIT(18) #define SD0_ITAPCHGWIN BIT(9) #define SD1_ITAPCHGWIN BIT(25) #define SD0_ITAPDLYENA BIT(8) #define SD1_ITAPDLYENA BIT(24) #define SD0_ITAPDLYSEL_MASK GENMASK(7, 0) #define SD1_ITAPDLYSEL_MASK GENMASK(23, 16) #define SD0_OTAPDLYSEL_MASK GENMASK(5, 0) #define SD1_OTAPDLYSEL_MASK GENMASK(21, 16) #define MIN_PHY_CLK_HZ 50000000 #define PHY_CTRL_REG1 0x270 #define PHY_CTRL_ITAPDLY_ENA_MASK BIT(0) #define PHY_CTRL_ITAPDLY_SEL_MASK GENMASK(5, 1) #define PHY_CTRL_ITAPDLY_SEL_SHIFT 1 #define PHY_CTRL_ITAP_CHG_WIN_MASK BIT(6) #define PHY_CTRL_OTAPDLY_ENA_MASK BIT(8) #define PHY_CTRL_OTAPDLY_SEL_MASK GENMASK(15, 12) #define PHY_CTRL_OTAPDLY_SEL_SHIFT 12 #define PHY_CTRL_STRB_SEL_MASK GENMASK(23, 16) #define PHY_CTRL_STRB_SEL_SHIFT 16 #define PHY_CTRL_TEST_CTRL_MASK GENMASK(31, 24) #define PHY_CTRL_REG2 0x274 #define PHY_CTRL_EN_DLL_MASK BIT(0) #define PHY_CTRL_DLL_RDY_MASK BIT(1) #define PHY_CTRL_FREQ_SEL_MASK GENMASK(6, 4) #define PHY_CTRL_FREQ_SEL_SHIFT 4 #define PHY_CTRL_SEL_DLY_TX_MASK BIT(16) #define PHY_CTRL_SEL_DLY_RX_MASK BIT(17) #define FREQSEL_200M_170M 0x0 #define FREQSEL_170M_140M 0x1 #define FREQSEL_140M_110M 0x2 #define FREQSEL_110M_80M 0x3 #define FREQSEL_80M_50M 0x4 #define FREQSEL_275M_250M 0x5 #define FREQSEL_250M_225M 0x6 #define FREQSEL_225M_200M 0x7 #define PHY_DLL_TIMEOUT_MS 100 #define VERSAL_NET_EMMC_ICLK_PHASE_DDR52_DLY_CHAIN 39 #define VERSAL_NET_EMMC_ICLK_PHASE_DDR52_DLL 146 #define VERSAL_NET_PHY_CTRL_STRB90_STRB180_VAL 0X77 struct arasan_sdhci_clk_data { int clk_phase_in[MMC_TIMING_MMC_HS400 + 1]; int clk_phase_out[MMC_TIMING_MMC_HS400 + 1]; }; struct arasan_sdhci_plat { struct mmc_config cfg; struct mmc mmc; }; struct arasan_sdhci_priv { struct sdhci_host *host; struct arasan_sdhci_clk_data clk_data; u32 node_id; u8 bank; u8 no_1p8; bool internal_phy_reg; struct reset_ctl_bulk resets; }; /* For Versal platforms zynqmp_mmio_write() won't be available */ __weak int zynqmp_mmio_write(const u32 address, const u32 mask, const u32 value) { return 0; } __weak int xilinx_pm_request(u32 api_id, u32 arg0, u32 arg1, u32 arg2, u32 arg3, u32 *ret_payload) { return 0; } __weak int zynqmp_pm_is_function_supported(const u32 api_id, const u32 id) { return 1; } #if defined(CONFIG_ARCH_ZYNQMP) || defined(CONFIG_ARCH_VERSAL) || defined(CONFIG_ARCH_VERSAL_NET) /* Default settings for ZynqMP Clock Phases */ static const u32 zynqmp_iclk_phases[] = {0, 63, 63, 0, 63, 0, 0, 183, 54, 0, 0}; static const u32 zynqmp_oclk_phases[] = {0, 72, 60, 0, 60, 72, 135, 48, 72, 135, 0}; /* Default settings for Versal Clock Phases */ static const u32 versal_iclk_phases[] = {0, 132, 132, 0, 132, 0, 0, 162, 90, 0, 0}; static const u32 versal_oclk_phases[] = {0, 60, 48, 0, 48, 72, 90, 36, 60, 90, 0}; /* Default settings for versal-net eMMC Clock Phases */ static const u32 versal_net_emmc_iclk_phases[] = {0, 0, 0, 0, 0, 0, 0, 0, 39, 0, 0}; static const u32 versal_net_emmc_oclk_phases[] = {0, 113, 0, 0, 0, 0, 0, 0, 113, 79, 45}; static const u8 mode2timing[] = { [MMC_LEGACY] = MMC_TIMING_LEGACY, [MMC_HS] = MMC_TIMING_MMC_HS, [SD_HS] = MMC_TIMING_SD_HS, [MMC_HS_52] = MMC_TIMING_MMC_HS, [MMC_DDR_52] = MMC_TIMING_MMC_DDR52, [UHS_SDR12] = MMC_TIMING_UHS_SDR12, [UHS_SDR25] = MMC_TIMING_UHS_SDR25, [UHS_SDR50] = MMC_TIMING_UHS_SDR50, [UHS_DDR50] = MMC_TIMING_UHS_DDR50, [UHS_SDR104] = MMC_TIMING_UHS_SDR104, [MMC_HS_200] = MMC_TIMING_MMC_HS200, [MMC_HS_400] = MMC_TIMING_MMC_HS400, }; #if defined(CONFIG_ARCH_VERSAL_NET) /** * arasan_phy_set_delaychain - Set eMMC delay chain based Input/Output clock * * @host: Pointer to the sdhci_host structure * @enable: Enable or disable Delay chain based Tx and Rx clock * Return: None * * Enable or disable eMMC delay chain based Input and Output clock in * PHY_CTRL_REG2 */ static void arasan_phy_set_delaychain(struct sdhci_host *host, bool enable) { u32 reg; reg = sdhci_readw(host, PHY_CTRL_REG2); if (enable) reg |= PHY_CTRL_SEL_DLY_TX_MASK | PHY_CTRL_SEL_DLY_RX_MASK; else reg &= ~(PHY_CTRL_SEL_DLY_TX_MASK | PHY_CTRL_SEL_DLY_RX_MASK); sdhci_writew(host, reg, PHY_CTRL_REG2); } /** * arasan_phy_set_dll - Set eMMC DLL clock * * @host: Pointer to the sdhci_host structure * @enable: Enable or disable DLL clock * Return: 0 if success or timeout error * * Enable or disable eMMC DLL clock in PHY_CTRL_REG2. When DLL enable is * set, wait till DLL is locked */ static int arasan_phy_set_dll(struct sdhci_host *host, bool enable) { u32 reg; reg = sdhci_readw(host, PHY_CTRL_REG2); if (enable) reg |= PHY_CTRL_EN_DLL_MASK; else reg &= ~PHY_CTRL_EN_DLL_MASK; sdhci_writew(host, reg, PHY_CTRL_REG2); /* If DLL is disabled return success */ if (!enable) return 0; /* If DLL is enabled wait till DLL loop is locked, which is * indicated by dll_rdy bit(bit1) in PHY_CTRL_REG2 */ return readl_relaxed_poll_timeout(host->ioaddr + PHY_CTRL_REG2, reg, (reg & PHY_CTRL_DLL_RDY_MASK), 1000 * PHY_DLL_TIMEOUT_MS); } /** * arasan_phy_dll_set_freq - Select frequency range of DLL for eMMC * * @host: Pointer to the sdhci_host structure * @clock: clock value * Return: None * * Set frequency range bits based on the selected clock for eMMC */ static void arasan_phy_dll_set_freq(struct sdhci_host *host, int clock) { u32 reg, freq_sel, freq; freq = DIV_ROUND_CLOSEST(clock, 1000000); if (freq <= 200 && freq > 170) freq_sel = FREQSEL_200M_170M; else if (freq <= 170 && freq > 140) freq_sel = FREQSEL_170M_140M; else if (freq <= 140 && freq > 110) freq_sel = FREQSEL_140M_110M; else if (freq <= 110 && freq > 80) freq_sel = FREQSEL_110M_80M; else freq_sel = FREQSEL_80M_50M; reg = sdhci_readw(host, PHY_CTRL_REG2); reg &= ~PHY_CTRL_FREQ_SEL_MASK; reg |= (freq_sel << PHY_CTRL_FREQ_SEL_SHIFT); sdhci_writew(host, reg, PHY_CTRL_REG2); } static int arasan_sdhci_config_dll(struct sdhci_host *host, unsigned int clock, bool enable) { struct mmc *mmc = (struct mmc *)host->mmc; struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev); if (enable) { if (priv->internal_phy_reg && clock >= MIN_PHY_CLK_HZ && enable) arasan_phy_set_dll(host, 1); return 0; } if (priv->internal_phy_reg && clock >= MIN_PHY_CLK_HZ) { sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); arasan_phy_set_dll(host, 0); arasan_phy_set_delaychain(host, 0); arasan_phy_dll_set_freq(host, clock); return 0; } sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); arasan_phy_set_delaychain(host, 1); return 0; } #endif static inline int arasan_zynqmp_set_in_tapdelay(u32 node_id, u32 itap_delay) { int ret; if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) { if (node_id == NODE_SD_0) { ret = zynqmp_mmio_write(SD_ITAP_DLY, SD0_ITAPCHGWIN, SD0_ITAPCHGWIN); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD0_ITAPDLYENA, SD0_ITAPDLYENA); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD0_ITAPDLYSEL_MASK, itap_delay); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD0_ITAPCHGWIN, 0); if (ret) return ret; } ret = zynqmp_mmio_write(SD_ITAP_DLY, SD1_ITAPCHGWIN, SD1_ITAPCHGWIN); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD1_ITAPDLYENA, SD1_ITAPDLYENA); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD1_ITAPDLYSEL_MASK, (itap_delay << 16)); if (ret) return ret; ret = zynqmp_mmio_write(SD_ITAP_DLY, SD1_ITAPCHGWIN, 0); if (ret) return ret; } else { return xilinx_pm_request(PM_IOCTL, node_id, IOCTL_SET_SD_TAPDELAY, PM_TAPDELAY_INPUT, itap_delay, NULL); } return 0; } static inline int arasan_zynqmp_set_out_tapdelay(u32 node_id, u32 otap_delay) { if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) { if (node_id == NODE_SD_0) return zynqmp_mmio_write(SD_OTAP_DLY, SD0_OTAPDLYSEL_MASK, otap_delay); return zynqmp_mmio_write(SD_OTAP_DLY, SD1_OTAPDLYSEL_MASK, (otap_delay << 16)); } else { return xilinx_pm_request(PM_IOCTL, node_id, IOCTL_SET_SD_TAPDELAY, PM_TAPDELAY_OUTPUT, otap_delay, NULL); } } static inline int zynqmp_dll_reset(u32 node_id, u32 type) { if (IS_ENABLED(CONFIG_SPL_BUILD) || current_el() == 3) { if (node_id == NODE_SD_0) return zynqmp_mmio_write(SD_DLL_CTRL, SD0_DLL_RST, type == PM_DLL_RESET_ASSERT ? SD0_DLL_RST : 0); return zynqmp_mmio_write(SD_DLL_CTRL, SD1_DLL_RST, type == PM_DLL_RESET_ASSERT ? SD1_DLL_RST : 0); } else { return xilinx_pm_request(PM_IOCTL, node_id, IOCTL_SD_DLL_RESET, type, 0, NULL); } } static int arasan_zynqmp_dll_reset(struct sdhci_host *host, u32 node_id) { struct mmc *mmc = (struct mmc *)host->mmc; struct udevice *dev = mmc->dev; unsigned long timeout; int ret; u16 clk; clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); clk &= ~(SDHCI_CLOCK_CARD_EN); sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); /* Issue DLL Reset */ ret = zynqmp_dll_reset(node_id, PM_DLL_RESET_ASSERT); if (ret) { dev_err(dev, "dll_reset assert failed with err: %d\n", ret); return ret; } /* Allow atleast 1ms delay for proper DLL reset */ mdelay(1); ret = zynqmp_dll_reset(node_id, PM_DLL_RESET_RELEASE); if (ret) { dev_err(dev, "dll_reset release failed with err: %d\n", ret); return ret; } /* Wait max 20 ms */ timeout = 100; while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL)) & SDHCI_CLOCK_INT_STABLE)) { if (timeout == 0) { dev_err(dev, ": Internal clock never stabilised.\n"); return -EBUSY; } timeout--; udelay(1000); } clk |= SDHCI_CLOCK_CARD_EN; sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL); return 0; } static int arasan_sdhci_execute_tuning(struct mmc *mmc, u8 opcode) { struct mmc_cmd cmd; struct mmc_data data; u32 ctrl; struct sdhci_host *host; struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev); int tuning_loop_counter = SDHCI_TUNING_LOOP_COUNT; dev_dbg(mmc->dev, "%s\n", __func__); host = priv->host; ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); ctrl |= SDHCI_CTRL_EXEC_TUNING; sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2); mdelay(1); arasan_zynqmp_dll_reset(host, priv->node_id); sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE); sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE); do { cmd.cmdidx = opcode; cmd.resp_type = MMC_RSP_R1; cmd.cmdarg = 0; data.blocksize = 64; data.blocks = 1; data.flags = MMC_DATA_READ; if (tuning_loop_counter-- == 0) break; if (cmd.cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200 && mmc->bus_width == 8) data.blocksize = 128; sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG, data.blocksize), SDHCI_BLOCK_SIZE); sdhci_writew(host, data.blocks, SDHCI_BLOCK_COUNT); sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); mmc_send_cmd(mmc, &cmd, NULL); ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); if (cmd.cmdidx == MMC_CMD_SEND_TUNING_BLOCK) udelay(1); } while (ctrl & SDHCI_CTRL_EXEC_TUNING); if (tuning_loop_counter < 0) { ctrl &= ~SDHCI_CTRL_TUNED_CLK; sdhci_writel(host, ctrl, SDHCI_HOST_CONTROL2); } if (!(ctrl & SDHCI_CTRL_TUNED_CLK)) { printf("%s:Tuning failed\n", __func__); return -1; } udelay(1); arasan_zynqmp_dll_reset(host, priv->node_id); /* Enable only interrupts served by the SD controller */ sdhci_writel(host, SDHCI_INT_DATA_MASK | SDHCI_INT_CMD_MASK, SDHCI_INT_ENABLE); /* Mask all sdhci interrupt sources */ sdhci_writel(host, 0x0, SDHCI_SIGNAL_ENABLE); return 0; } /** * sdhci_zynqmp_sdcardclk_set_phase - Set the SD Output Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set the SD Output Clock Tap Delays for Output path */ static int sdhci_zynqmp_sdcardclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; struct udevice *dev = mmc->dev; struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev); u8 tap_delay, tap_max = 0; int timing = mode2timing[mmc->selected_mode]; int ret; /* * This is applicable for SDHCI_SPEC_300 and above * ZynqMP does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_SD_HS: case MMC_TIMING_UHS_SDR25: case MMC_TIMING_UHS_DDR50: case MMC_TIMING_MMC_DDR52: /* For 50MHz clock, 30 Taps are available */ tap_max = 30; break; case MMC_TIMING_UHS_SDR50: /* For 100MHz clock, 15 Taps are available */ tap_max = 15; break; case MMC_TIMING_UHS_SDR104: case MMC_TIMING_MMC_HS200: /* For 200MHz clock, 8 Taps are available */ tap_max = 8; default: break; } tap_delay = (degrees * tap_max) / 360; /* Limit output tap_delay value to 6 bits */ tap_delay &= SDHCI_ARASAN_OTAPDLY_SEL_MASK; /* Set the Clock Phase */ ret = arasan_zynqmp_set_out_tapdelay(priv->node_id, tap_delay); if (ret) { dev_err(dev, "Error setting output Tap Delay\n"); return ret; } /* Release DLL Reset */ ret = zynqmp_dll_reset(priv->node_id, PM_DLL_RESET_RELEASE); if (ret) { dev_err(dev, "dll_reset release failed with err: %d\n", ret); return ret; } return 0; } /** * sdhci_zynqmp_sampleclk_set_phase - Set the SD Input Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set the SD Input Clock Tap Delays for Input path */ static int sdhci_zynqmp_sampleclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; struct udevice *dev = mmc->dev; struct arasan_sdhci_priv *priv = dev_get_priv(mmc->dev); u8 tap_delay, tap_max = 0; int timing = mode2timing[mmc->selected_mode]; int ret; /* * This is applicable for SDHCI_SPEC_300 and above * ZynqMP does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; /* Assert DLL Reset */ ret = zynqmp_dll_reset(priv->node_id, PM_DLL_RESET_ASSERT); if (ret) { dev_err(dev, "dll_reset assert failed with err: %d\n", ret); return ret; } switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_SD_HS: case MMC_TIMING_UHS_SDR25: case MMC_TIMING_UHS_DDR50: case MMC_TIMING_MMC_DDR52: /* For 50MHz clock, 120 Taps are available */ tap_max = 120; break; case MMC_TIMING_UHS_SDR50: /* For 100MHz clock, 60 Taps are available */ tap_max = 60; break; case MMC_TIMING_UHS_SDR104: case MMC_TIMING_MMC_HS200: /* For 200MHz clock, 30 Taps are available */ tap_max = 30; default: break; } tap_delay = (degrees * tap_max) / 360; /* Limit input tap_delay value to 8 bits */ tap_delay &= SDHCI_ARASAN_ITAPDLY_SEL_MASK; ret = arasan_zynqmp_set_in_tapdelay(priv->node_id, tap_delay); if (ret) { dev_err(dev, "Error setting Input Tap Delay\n"); return ret; } return 0; } /** * sdhci_versal_sdcardclk_set_phase - Set the SD Output Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set the SD Output Clock Tap Delays for Output path */ static int sdhci_versal_sdcardclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; u8 tap_delay, tap_max = 0; int timing = mode2timing[mmc->selected_mode]; u32 regval; /* * This is applicable for SDHCI_SPEC_300 and above * Versal does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_SD_HS: case MMC_TIMING_UHS_SDR25: case MMC_TIMING_UHS_DDR50: case MMC_TIMING_MMC_DDR52: /* For 50MHz clock, 30 Taps are available */ tap_max = 30; break; case MMC_TIMING_UHS_SDR50: /* For 100MHz clock, 15 Taps are available */ tap_max = 15; break; case MMC_TIMING_UHS_SDR104: case MMC_TIMING_MMC_HS200: /* For 200MHz clock, 8 Taps are available */ tap_max = 8; default: break; } tap_delay = (degrees * tap_max) / 360; /* Limit output tap_delay value to 6 bits */ tap_delay &= SDHCI_ARASAN_OTAPDLY_SEL_MASK; /* Set the Clock Phase */ regval = sdhci_readl(host, SDHCI_ARASAN_OTAPDLY_REGISTER); regval |= SDHCI_OTAPDLY_ENABLE; sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER); regval &= ~SDHCI_ARASAN_OTAPDLY_SEL_MASK; regval |= tap_delay; sdhci_writel(host, regval, SDHCI_ARASAN_OTAPDLY_REGISTER); return 0; } /** * sdhci_versal_sampleclk_set_phase - Set the SD Input Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set the SD Input Clock Tap Delays for Input path */ static int sdhci_versal_sampleclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; u8 tap_delay, tap_max = 0; int timing = mode2timing[mmc->selected_mode]; u32 regval; /* * This is applicable for SDHCI_SPEC_300 and above * Versal does not set phase for <=25MHz clock. * If degrees is zero, no need to do anything. */ if (SDHCI_GET_VERSION(host) < SDHCI_SPEC_300) return 0; switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_SD_HS: case MMC_TIMING_UHS_SDR25: case MMC_TIMING_UHS_DDR50: case MMC_TIMING_MMC_DDR52: /* For 50MHz clock, 120 Taps are available */ tap_max = 120; break; case MMC_TIMING_UHS_SDR50: /* For 100MHz clock, 60 Taps are available */ tap_max = 60; break; case MMC_TIMING_UHS_SDR104: case MMC_TIMING_MMC_HS200: /* For 200MHz clock, 30 Taps are available */ tap_max = 30; default: break; } tap_delay = (degrees * tap_max) / 360; /* Limit input tap_delay value to 8 bits */ tap_delay &= SDHCI_ARASAN_ITAPDLY_SEL_MASK; /* Set the Clock Phase */ regval = sdhci_readl(host, SDHCI_ARASAN_ITAPDLY_REGISTER); regval |= SDHCI_ITAPDLY_CHGWIN; sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); regval |= SDHCI_ITAPDLY_ENABLE; sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); regval &= ~SDHCI_ARASAN_ITAPDLY_SEL_MASK; regval |= tap_delay; sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); regval &= ~SDHCI_ITAPDLY_CHGWIN; sdhci_writel(host, regval, SDHCI_ARASAN_ITAPDLY_REGISTER); return 0; } /** * sdhci_versal_net_emmc_sdcardclk_set_phase - Set eMMC Output Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set eMMC Output Clock Tap Delays for Output path */ static int sdhci_versal_net_emmc_sdcardclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; int timing = mode2timing[mmc->selected_mode]; u8 tap_delay, tap_max = 0; u32 regval; switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_MMC_DDR52: tap_max = 16; break; case MMC_TIMING_MMC_HS200: case MMC_TIMING_MMC_HS400: /* For 200MHz clock, 32 Taps are available */ tap_max = 32; break; default: break; } tap_delay = (degrees * tap_max) / 360; /* Set the Clock Phase */ if (tap_delay) { regval = sdhci_readl(host, PHY_CTRL_REG1); regval |= PHY_CTRL_OTAPDLY_ENA_MASK; sdhci_writel(host, regval, PHY_CTRL_REG1); regval &= ~PHY_CTRL_OTAPDLY_SEL_MASK; regval |= tap_delay << PHY_CTRL_OTAPDLY_SEL_SHIFT; sdhci_writel(host, regval, PHY_CTRL_REG1); } return 0; } /** * sdhci_versal_net_emmc_sampleclk_set_phase - Set eMMC Input Clock Tap Delays * * @host: Pointer to the sdhci_host structure. * @degrees: The clock phase shift between 0 - 359. * Return: 0 * * Set eMMC Input Clock Tap Delays for Input path. If HS400 is selected, * set strobe90 and strobe180 in PHY_CTRL_REG1. */ static int sdhci_versal_net_emmc_sampleclk_set_phase(struct sdhci_host *host, int degrees) { struct mmc *mmc = (struct mmc *)host->mmc; int timing = mode2timing[mmc->selected_mode]; u8 tap_delay, tap_max = 0; u32 regval; switch (timing) { case MMC_TIMING_MMC_HS: case MMC_TIMING_MMC_DDR52: tap_max = 32; break; case MMC_TIMING_MMC_HS400: /* Strobe select tap point for strb90 and strb180 */ regval = sdhci_readl(host, PHY_CTRL_REG1); regval &= ~PHY_CTRL_STRB_SEL_MASK; regval |= VERSAL_NET_PHY_CTRL_STRB90_STRB180_VAL << PHY_CTRL_STRB_SEL_SHIFT; sdhci_writel(host, regval, PHY_CTRL_REG1); break; default: break; } tap_delay = (degrees * tap_max) / 360; /* Set the Clock Phase */ if (tap_delay) { regval = sdhci_readl(host, PHY_CTRL_REG1); regval |= PHY_CTRL_ITAP_CHG_WIN_MASK; sdhci_writel(host, regval, PHY_CTRL_REG1); regval |= PHY_CTRL_ITAPDLY_ENA_MASK; sdhci_writel(host, regval, PHY_CTRL_REG1); regval &= ~PHY_CTRL_ITAPDLY_SEL_MASK; regval |= tap_delay << PHY_CTRL_ITAPDLY_SEL_SHIFT; sdhci_writel(host, regval, PHY_CTRL_REG1); regval &= ~PHY_CTRL_ITAP_CHG_WIN_MASK; sdhci_writel(host, regval, PHY_CTRL_REG1); } return 0; } static int arasan_sdhci_set_tapdelay(struct sdhci_host *host) { struct arasan_sdhci_priv *priv = dev_get_priv(host->mmc->dev); struct arasan_sdhci_clk_data *clk_data = &priv->clk_data; struct mmc *mmc = (struct mmc *)host->mmc; struct udevice *dev = mmc->dev; u8 timing = mode2timing[mmc->selected_mode]; u32 iclk_phase = clk_data->clk_phase_in[timing]; u32 oclk_phase = clk_data->clk_phase_out[timing]; int ret; dev_dbg(dev, "%s, host:%s, mode:%d\n", __func__, host->name, timing); if (IS_ENABLED(CONFIG_ARCH_ZYNQMP) && device_is_compatible(dev, "xlnx,zynqmp-8.9a")) { ret = sdhci_zynqmp_sampleclk_set_phase(host, iclk_phase); if (ret) return ret; ret = sdhci_zynqmp_sdcardclk_set_phase(host, oclk_phase); if (ret) return ret; } else if (IS_ENABLED(CONFIG_ARCH_VERSAL) && device_is_compatible(dev, "xlnx,versal-8.9a")) { ret = sdhci_versal_sampleclk_set_phase(host, iclk_phase); if (ret) return ret; ret = sdhci_versal_sdcardclk_set_phase(host, oclk_phase); if (ret) return ret; } else if (IS_ENABLED(CONFIG_ARCH_VERSAL_NET) && device_is_compatible(dev, "xlnx,versal-net-5.1-emmc")) { if (mmc->clock >= MIN_PHY_CLK_HZ) if (iclk_phase == VERSAL_NET_EMMC_ICLK_PHASE_DDR52_DLY_CHAIN) iclk_phase = VERSAL_NET_EMMC_ICLK_PHASE_DDR52_DLL; ret = sdhci_versal_net_emmc_sampleclk_set_phase(host, iclk_phase); if (ret) return ret; ret = sdhci_versal_net_emmc_sdcardclk_set_phase(host, oclk_phase); if (ret) return ret; } return 0; } static void arasan_dt_read_clk_phase(struct udevice *dev, unsigned char timing, const char *prop) { struct arasan_sdhci_priv *priv = dev_get_priv(dev); struct arasan_sdhci_clk_data *clk_data = &priv->clk_data; u32 clk_phase[2] = {0}; /* * Read Tap Delay values from DT, if the DT does not contain the * Tap Values then use the pre-defined values */ if (dev_read_u32_array(dev, prop, &clk_phase[0], 2)) { dev_dbg(dev, "Using predefined clock phase for %s = %d %d\n", prop, clk_data->clk_phase_in[timing], clk_data->clk_phase_out[timing]); return; } /* The values read are Input and Output Clock Delays in order */ clk_data->clk_phase_in[timing] = clk_phase[0]; clk_data->clk_phase_out[timing] = clk_phase[1]; } /** * arasan_dt_parse_clk_phases - Read Tap Delay values from DT * * @dev: Pointer to our struct udevice. * * Called at initialization to parse the values of Tap Delays. */ static void arasan_dt_parse_clk_phases(struct udevice *dev) { struct arasan_sdhci_priv *priv = dev_get_priv(dev); struct arasan_sdhci_clk_data *clk_data = &priv->clk_data; int i; if (IS_ENABLED(CONFIG_ARCH_ZYNQMP) && device_is_compatible(dev, "xlnx,zynqmp-8.9a")) { for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) { clk_data->clk_phase_in[i] = zynqmp_iclk_phases[i]; clk_data->clk_phase_out[i] = zynqmp_oclk_phases[i]; } if (priv->bank == MMC_BANK2) { clk_data->clk_phase_out[MMC_TIMING_UHS_SDR104] = 90; clk_data->clk_phase_out[MMC_TIMING_MMC_HS200] = 90; } } if (IS_ENABLED(CONFIG_ARCH_VERSAL) && device_is_compatible(dev, "xlnx,versal-8.9a")) { for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) { clk_data->clk_phase_in[i] = versal_iclk_phases[i]; clk_data->clk_phase_out[i] = versal_oclk_phases[i]; } } if (IS_ENABLED(CONFIG_ARCH_VERSAL_NET) && device_is_compatible(dev, "xlnx,versal-net-5.1-emmc")) { for (i = 0; i <= MMC_TIMING_MMC_HS400; i++) { clk_data->clk_phase_in[i] = versal_net_emmc_iclk_phases[i]; clk_data->clk_phase_out[i] = versal_net_emmc_oclk_phases[i]; } } arasan_dt_read_clk_phase(dev, MMC_TIMING_LEGACY, "clk-phase-legacy"); arasan_dt_read_clk_phase(dev, MMC_TIMING_MMC_HS, "clk-phase-mmc-hs"); arasan_dt_read_clk_phase(dev, MMC_TIMING_SD_HS, "clk-phase-sd-hs"); arasan_dt_read_clk_phase(dev, MMC_TIMING_UHS_SDR12, "clk-phase-uhs-sdr12"); arasan_dt_read_clk_phase(dev, MMC_TIMING_UHS_SDR25, "clk-phase-uhs-sdr25"); arasan_dt_read_clk_phase(dev, MMC_TIMING_UHS_SDR50, "clk-phase-uhs-sdr50"); arasan_dt_read_clk_phase(dev, MMC_TIMING_UHS_SDR104, "clk-phase-uhs-sdr104"); arasan_dt_read_clk_phase(dev, MMC_TIMING_UHS_DDR50, "clk-phase-uhs-ddr50"); arasan_dt_read_clk_phase(dev, MMC_TIMING_MMC_DDR52, "clk-phase-mmc-ddr52"); arasan_dt_read_clk_phase(dev, MMC_TIMING_MMC_HS200, "clk-phase-mmc-hs200"); arasan_dt_read_clk_phase(dev, MMC_TIMING_MMC_HS400, "clk-phase-mmc-hs400"); } static const struct sdhci_ops arasan_ops = { .platform_execute_tuning = &arasan_sdhci_execute_tuning, .set_delay = &arasan_sdhci_set_tapdelay, .set_control_reg = &sdhci_set_control_reg, #if defined(CONFIG_ARCH_VERSAL_NET) .config_dll = &arasan_sdhci_config_dll, #endif }; #endif #if defined(CONFIG_ARCH_ZYNQMP) && defined(CONFIG_ZYNQMP_FIRMWARE) static int sdhci_zynqmp_set_dynamic_config(struct arasan_sdhci_priv *priv, struct udevice *dev) { int ret; struct clk clk; unsigned long clock, mhz; ret = xilinx_pm_request(PM_REQUEST_NODE, priv->node_id, ZYNQMP_PM_CAPABILITY_ACCESS, ZYNQMP_PM_MAX_QOS, ZYNQMP_PM_REQUEST_ACK_NO, NULL); if (ret) { dev_err(dev, "Request node failed for %d\n", priv->node_id); return ret; } ret = reset_get_bulk(dev, &priv->resets); if (ret == -ENOTSUPP || ret == -ENOENT) { dev_err(dev, "Reset not found\n"); return 0; } else if (ret) { dev_err(dev, "Reset failed\n"); return ret; } ret = reset_assert_bulk(&priv->resets); if (ret) { dev_err(dev, "Reset assert failed\n"); return ret; } ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_FIXED, 0); if (ret) { dev_err(dev, "SD_CONFIG_FIXED failed\n"); return ret; } ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_EMMC_SEL, dev_read_bool(dev, "non-removable")); if (ret) { dev_err(dev, "SD_CONFIG_EMMC_SEL failed\n"); return ret; } ret = clk_get_by_index(dev, 0, &clk); if (ret < 0) { dev_err(dev, "failed to get clock\n"); return ret; } clock = clk_get_rate(&clk); if (IS_ERR_VALUE(clock)) { dev_err(dev, "failed to get rate\n"); return clock; } mhz = DIV64_U64_ROUND_UP(clock, 1000000); if (mhz > 100 && mhz <= 200) mhz = 200; else if (mhz > 50 && mhz <= 100) mhz = 100; else if (mhz > 25 && mhz <= 50) mhz = 50; else mhz = 25; ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_BASECLK, mhz); if (ret) { dev_err(dev, "SD_CONFIG_BASECLK failed\n"); return ret; } ret = zynqmp_pm_set_sd_config(priv->node_id, SD_CONFIG_8BIT, (dev_read_u32_default(dev, "bus-width", 1) == 8)); if (ret) { dev_err(dev, "SD_CONFIG_8BIT failed\n"); return ret; } ret = reset_deassert_bulk(&priv->resets); if (ret) { dev_err(dev, "Reset release failed\n"); return ret; } return 0; } #endif static int arasan_sdhci_probe(struct udevice *dev) { struct arasan_sdhci_plat *plat = dev_get_plat(dev); struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); struct arasan_sdhci_priv *priv = dev_get_priv(dev); struct sdhci_host *host; struct clk clk; unsigned long clock; int ret; host = priv->host; #if defined(CONFIG_ARCH_ZYNQMP) && defined(CONFIG_ZYNQMP_FIRMWARE) if (device_is_compatible(dev, "xlnx,zynqmp-8.9a")) { ret = zynqmp_pm_is_function_supported(PM_IOCTL, IOCTL_SET_SD_CONFIG); if (!ret) { ret = sdhci_zynqmp_set_dynamic_config(priv, dev); if (ret) return ret; } } #endif if (device_is_compatible(dev, "xlnx,versal-net-5.1-emmc")) priv->internal_phy_reg = true; ret = clk_get_by_index(dev, 0, &clk); if (ret < 0) { dev_err(dev, "failed to get clock\n"); return ret; } clock = clk_get_rate(&clk); if (IS_ERR_VALUE(clock)) { dev_err(dev, "failed to get rate\n"); return clock; } dev_dbg(dev, "%s: CLK %ld\n", __func__, clock); ret = clk_enable(&clk); if (ret) { dev_err(dev, "failed to enable clock\n"); return ret; } host->quirks = SDHCI_QUIRK_WAIT_SEND_CMD | SDHCI_QUIRK_BROKEN_R1B; #ifdef CONFIG_ZYNQ_HISPD_BROKEN host->quirks |= SDHCI_QUIRK_BROKEN_HISPD_MODE; #endif if (priv->no_1p8) host->quirks |= SDHCI_QUIRK_NO_1_8_V; if (CONFIG_IS_ENABLED(ARCH_VERSAL_NET) && device_is_compatible(dev, "xlnx,versal-net-5.1-emmc")) host->quirks |= SDHCI_QUIRK_CAPS_BIT63_FOR_HS400; plat->cfg.f_max = CONFIG_ZYNQ_SDHCI_MAX_FREQ; ret = mmc_of_parse(dev, &plat->cfg); if (ret) return ret; host->max_clk = clock; host->mmc = &plat->mmc; host->mmc->dev = dev; host->mmc->priv = host; ret = sdhci_setup_cfg(&plat->cfg, host, plat->cfg.f_max, CONFIG_ZYNQ_SDHCI_MIN_FREQ); if (ret) return ret; upriv->mmc = host->mmc; /* * WORKAROUND: Versal platforms have an issue with card detect state. * Due to this, host controller is switching off voltage to sd card * causing sd card timeout error. Workaround this by adding a wait for * 1000msec till the card detect state gets stable. */ if (IS_ENABLED(CONFIG_ARCH_ZYNQMP) || IS_ENABLED(CONFIG_ARCH_VERSAL)) { u32 timeout = 1000000; while (((sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_STATE_STABLE) == 0) && timeout) { udelay(1); timeout--; } if (!timeout) { dev_err(dev, "Sdhci card detect state not stable\n"); return -ETIMEDOUT; } } return sdhci_probe(dev); } static int arasan_sdhci_of_to_plat(struct udevice *dev) { struct arasan_sdhci_priv *priv = dev_get_priv(dev); u32 pm_info[2]; priv->host = calloc(1, sizeof(struct sdhci_host)); if (!priv->host) return -1; priv->host->name = dev->name; #if defined(CONFIG_ARCH_ZYNQMP) || defined(CONFIG_ARCH_VERSAL) || defined(CONFIG_ARCH_VERSAL_NET) priv->host->ops = &arasan_ops; arasan_dt_parse_clk_phases(dev); #endif priv->host->ioaddr = (void *)dev_read_addr(dev); if (IS_ERR(priv->host->ioaddr)) return PTR_ERR(priv->host->ioaddr); priv->bank = dev_read_u32_default(dev, "xlnx,mio-bank", 0); priv->no_1p8 = dev_read_bool(dev, "no-1-8-v"); priv->node_id = 0; if (!dev_read_u32_array(dev, "power-domains", pm_info, ARRAY_SIZE(pm_info))) priv->node_id = pm_info[1]; return 0; } static int arasan_sdhci_bind(struct udevice *dev) { struct arasan_sdhci_plat *plat = dev_get_plat(dev); return sdhci_bind(dev, &plat->mmc, &plat->cfg); } static const struct udevice_id arasan_sdhci_ids[] = { { .compatible = "arasan,sdhci-8.9a" }, { .compatible = "xlnx,versal-net-5.1-emmc" }, { } }; U_BOOT_DRIVER(arasan_sdhci_drv) = { .name = "arasan_sdhci", .id = UCLASS_MMC, .of_match = arasan_sdhci_ids, .of_to_plat = arasan_sdhci_of_to_plat, .ops = &sdhci_ops, .bind = arasan_sdhci_bind, .probe = arasan_sdhci_probe, .priv_auto = sizeof(struct arasan_sdhci_priv), .plat_auto = sizeof(struct arasan_sdhci_plat), };