// SPDX-License-Identifier: (GPL-2.0+ OR MIT) // Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz> // Based on sun50i-h5-orangepi-pc2.dts, which is: // Copyright (C) 2016 ARM Ltd. /dts-v1/; #include "sun50i-h5.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { model = "Xunlong Orange Pi Prime"; compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5"; aliases { ethernet0 = &emac; serial0 = &uart0; }; chosen { stdout-path = "serial0:115200n8"; }; connector { compatible = "hdmi-connector"; type = "a"; port { hdmi_con_in: endpoint { remote-endpoint = <&hdmi_out_con>; }; }; }; leds { compatible = "gpio-leds"; led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; led-1 { label = "orangepi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; }; r-gpio-keys { compatible = "gpio-keys"; sw4 { label = "sw4"; linux,code = <BTN_0>; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; }; }; reg_gmac_3v3: gmac-3v3 { compatible = "regulator-fixed"; regulator-name = "gmac-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; startup-delay-us = <100000>; enable-active-high; gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; }; reg_vcc3v3: vcc3v3 { compatible = "regulator-fixed"; regulator-name = "vcc3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; reg_usb0_vbus: usb0-vbus { compatible = "regulator-fixed"; regulator-name = "usb0-vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; enable-active-high; gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ status = "okay"; }; wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */ }; }; &codec { allwinner,audio-routing = "Line Out", "LINEOUT", "MIC1", "Mic", "Mic", "MBIAS"; status = "okay"; }; &de { status = "okay"; }; &ehci0 { status = "okay"; }; &ehci1 { status = "okay"; }; &ehci2 { status = "okay"; }; &ehci3 { status = "okay"; }; &emac { pinctrl-names = "default"; pinctrl-0 = <&emac_rgmii_pins>; phy-supply = <®_gmac_3v3>; phy-handle = <&ext_rgmii_phy>; phy-mode = "rgmii-id"; status = "okay"; }; &external_mdio { ext_rgmii_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <1>; }; }; &hdmi { status = "okay"; }; &hdmi_out { hdmi_out_con: endpoint { remote-endpoint = <&hdmi_con_in>; }; }; &ir { pinctrl-names = "default"; pinctrl-0 = <&r_ir_rx_pin>; status = "okay"; }; &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ status = "okay"; }; &mmc1 { vmmc-supply = <®_vcc3v3>; mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; non-removable; status = "okay"; }; &ohci0 { status = "okay"; }; &ohci1 { status = "okay"; }; &ohci2 { status = "okay"; }; &ohci3 { status = "okay"; }; &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pa_pins>; status = "okay"; }; &uart1 { pinctrl-names = "default"; pinctrl-0 = <&uart1_pins>; status = "disabled"; }; &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; status = "disabled"; }; &usb_otg { dr_mode = "otg"; status = "okay"; }; &usbphy { /* USB Type-A ports' VBUS is always on */ usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */ usb0_vbus-supply = <®_usb0_vbus>; status = "okay"; };