/* SPDX-License-Identifier: GPL-2.0+ */ /* * Configuration header file for K3 J721E EVM * * Copyright (C) 2018-2020 Texas Instruments Incorporated - https://www.ti.com/ * Lokesh Vutla */ #ifndef __CONFIG_J721E_EVM_H #define __CONFIG_J721E_EVM_H #include #include #include #include #include /* DDR Configuration */ #define CONFIG_SYS_SDRAM_BASE1 0x880000000 /* SPL Loader Configuration */ #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \ CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE) #define CONFIG_SYS_UBOOT_BASE 0x50280000 /* Image load address in RAM for DFU boot*/ #else #define CONFIG_SYS_UBOOT_BASE 0x50080000 /* * Maximum size in memory allocated to the SPL BSS. Keep it as tight as * possible (to allow the build to go through), as this directly affects * our memory footprint. The less we use for BSS the more we have available * for everything else. */ #define CONFIG_SPL_BSS_MAX_SIZE 0xA000 /* * Link BSS to be within SPL in a dedicated region located near the top of * the MCU SRAM, this way making it available also before relocation. Note * that we are not using the actual top of the MCU SRAM as there is a memory * location filled in by the boot ROM that we want to read out without any * interference from the C context. */ #define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\ CONFIG_SPL_BSS_MAX_SIZE) /* Set the stack right below the SPL BSS section */ #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR /* Configure R5 SPL post-relocation malloc pool in DDR */ #define CONFIG_SYS_SPL_MALLOC_START 0x84000000 #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M /* Image load address in RAM for DFU boot*/ #endif #ifdef CONFIG_SYS_K3_SPL_ATF #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin" #endif #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE #define CONFIG_SYS_BOOTM_LEN SZ_64M #define CONFIG_CQSPI_REF_CLK 133333333 /* HyperFlash related configuration */ #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1 /* U-Boot general configuration */ #define EXTRA_ENV_J721E_BOARD_SETTINGS \ "default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ "findfdt=" \ "setenv name_fdt ${default_device_tree};" \ "setenv fdtfile ${name_fdt}\0" \ "name_kern=Image\0" \ "console=ttyS2,115200n8\0" \ "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000 " \ "${mtdparts}\0" \ "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" #define PARTS_DEFAULT \ /* Linux partitions */ \ "uuid_disk=${uuid_gpt_disk};" \ "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0" #ifdef CONFIG_SYS_K3_SPL_ATF #if defined(CONFIG_TARGET_J721E_R5_EVM) #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ "addr_mainr5f0_0load=0x88000000\0" \ "name_mainr5f0_0fw=/lib/firmware/j7-main-r5f0_0-fw\0" \ "addr_mcur5f0_0load=0x89000000\0" \ "name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0" #elif defined(CONFIG_TARGET_J7200_R5_EVM) #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ "addr_mcur5f0_0load=0x89000000\0" \ "name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0" #endif /* CONFIG_TARGET_J721E_R5_EVM */ #else #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC "" #endif /* CONFIG_SYS_K3_SPL_ATF */ /* U-Boot MMC-specific configuration */ #define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \ "boot=mmc\0" \ "mmcdev=1\0" \ "bootpart=1:2\0" \ "bootdir=/boot\0" \ EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ "rd_spec=-\0" \ "init_mmc=run args_all args_mmc\0" \ "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \ "get_overlay_mmc=" \ "fdt address ${fdtaddr};" \ "fdt resize 0x100000;" \ "for overlay in $name_overlays;" \ "do;" \ "load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \ "fdt apply ${dtboaddr};" \ "done;\0" \ "partitions=" PARTS_DEFAULT \ "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \ "${bootdir}/${name_kern}\0" \ "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \ "${bootdir}/${name_fit}\0" \ "partitions=" PARTS_DEFAULT /* Set the default list of remote processors to boot */ #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) #ifdef DEFAULT_RPROCS #undef DEFAULT_RPROCS #endif #endif #ifdef CONFIG_TARGET_J721E_A72_EVM #define DEFAULT_RPROCS "" \ "3 /lib/firmware/j7-main-r5f0_1-fw " \ "4 /lib/firmware/j7-main-r5f1_0-fw " \ "5 /lib/firmware/j7-main-r5f1_1-fw " \ "6 /lib/firmware/j7-c66_0-fw " \ "7 /lib/firmware/j7-c66_1-fw " \ "8 /lib/firmware/j7-c71_0-fw " #endif /* CONFIG_TARGET_J721E_A72_EVM */ #ifdef CONFIG_TARGET_J7200_A72_EVM #define DEFAULT_RPROCS "" \ "2 /lib/firmware/j7200-main-r5f0_0-fw " \ "3 /lib/firmware/j7200-main-r5f0_1-fw " #endif /* CONFIG_TARGET_J7200_A72_EVM */ /* set default dfu_bufsiz to 128KB (sector size of OSPI) */ #define EXTRA_ENV_DFUARGS \ "dfu_bufsiz=0x20000\0" \ DFU_ALT_INFO_MMC \ DFU_ALT_INFO_EMMC \ DFU_ALT_INFO_RAM \ DFU_ALT_INFO_OSPI #if defined(CONFIG_TARGET_J721E_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) #define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD \ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" #else #define EXTRA_ENV_J721E_BOARD_SETTINGS_MTD #endif #if CONFIG_IS_ENABLED(CMD_PXE) # define BOOT_TARGET_PXE(func) func(PXE, pxe, na) #else # define BOOT_TARGET_PXE(func) #endif #if CONFIG_IS_ENABLED(CMD_DHCP) # define BOOT_TARGET_DHCP(func) func(DHCP, dhcp, na) #else # define BOOT_TARGET_DHCP(func) #endif #define BOOT_TARGET_DEVICES(func) \ func(MMC, mmc, 1) \ func(MMC, mmc, 0) \ BOOT_TARGET_PXE(func) \ BOOT_TARGET_DHCP(func) #include /* Incorporate settings into the U-Boot environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ DEFAULT_LINUX_BOOT_ENV \ DEFAULT_MMC_TI_ARGS \ DEFAULT_FIT_TI_ARGS \ EXTRA_ENV_J721E_BOARD_SETTINGS \ EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \ EXTRA_ENV_RPROC_SETTINGS \ EXTRA_ENV_DFUARGS \ DEFAULT_UFS_TI_ARGS \ EXTRA_ENV_J721E_BOARD_SETTINGS_MTD \ BOOTENV /* Now for the remaining common defines */ #include /* MMC ENV related defines */ #endif /* __CONFIG_J721E_EVM_H */