For successful boot when CONFIG_SPL_OF_CONTROL=y, we need to ensure that
the board EEPROM on i2c0, the uart0 serial port and the relevant boot
device (mmc1 or mmc2) can be accessed in the SPL. We also need to
preserve the parent nodes for each required dtb node.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The signal name of pin PD8 with function D is A22_NANDCLE
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The sync of device-tree/bindings in 11a48a5a18c6 ("Linux 5.6-rc2") causes
Ethernet to break on some GXBB boards; the PHY seems to need proper reset
timing to function in u-boot and Linux. Re-add the old PHY reset binding
for dwmac until we support new bindings in the PHY node. This borrows the
same fix applied to the Odroid C2 board [0].
[0] https://lists.denx.de/pipermail/u-boot/2021-April/446658.html
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20221025143205.14470-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The fclk-enable property is set to 0 which disables all FCLKs.
Enable all FCLKs so they can be used as clock sources in the
programmable logic.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b1308dc1f14f8eb24662019f7376c959e5e763b8.1665567031.git.michal.simek@amd.com
We should guard the SPL nodes against CONFIG_SPL_BUILD to fix
the following build error when the blobs are absent:
binman: Fail open first container file mx8qm-ahab-container.img
Signed-off-by: Fabio Estevam <festevam@denx.de>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore:
Since commit the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
Core: 62 devices, 17 uclasses, devicetree: separate
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Note: Nowadays, the intent is for them regular device trees to just be
synchronised from them Linux kernel device trees and any and all U-Boot
specific changes need to go into the -u-boot.dtsi device tree include
files which BTW get included automatically by the U-Boot build system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate to using automatic build system included -u-boot.dtsi device
tree include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL. Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode. Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Multiple boards create duplicate entries in their respective
-u-boot.dtsi files which all basically do the same thing.
To consolidate these and make it easier to make improvements
going forward, consolidate them all into one place.
This file creates a flash.bin image using binman, and supports
LPDDR4, DDR4 and DDR3. Since individual boards use different
peripherals and different UART ports, those entries were kept
in their respective board files, but the spba1 node was addded
which contains all UART1-3 to help facilitate SPL_DM_SERIAL.
Individual users will still need to include their respective
UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file
which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is
enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP
devicetree file from linux-next tree.
commit <aec8ad34f7f24> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam devicetree file from linux-next tree.
commit <eefe06b295087> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus SoM)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmNSPhMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDrHCACddHL6pElPVUvNWomJ
h7RNejIaFrm+V2tVoDqnUBEzxKod7g1cvBiZM+2o5fcLNIrWfH0gV+7a48Uybzt2
r7VZ9u5Rnl1Fhhjvr8eL3uF/39V249eMPrzR8xC677sCJJkcczoOw8n4y534FaJZ
1NePmMKhlo7YVEZKzwdg1sM6sUppXniSEXUllWumVaUgSHcZhFK579nCbYpt25bW
sJ1V3fY2pJnaFHv9H599zSK79Izf5fR4fr3egKZknw8oqNLKNrjkWxxlPXJfjEYr
ncFJ31dOZXJU09rRoE60nIc0QdRE8dvELjYhPKUS/wmFDg7IotwNj5GcX2RIlRPJ
mS22
=D3FL
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.01 cycle:
This small fixes set includes an indentation fix for sam9x60 DT and one
name for one pin for sama7g5.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add Serial Download Protocol support as it is a useful method to
load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot
proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO
to reduce its size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.
With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:
$ uuu -brun spl flash.bin
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The indentation went far on the right due to an extra tab for
each pinctrl sub-nodes.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
The GW7903 revision B adds two additional GPIO's to control the
direction of the 2 isolated digital I/O circuits.
Define them as:
- dig1_ctl
- dig2_ctl
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the M2 socket gpio hogs such that they are not active on boot by
flagging them as GPIO_ACTIVE_HIGH so that 'output-high' drives high.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the UART config gpio hogs such that it is configured for RS232
by default on boot. Additionally rename them to match the names used
on the reset of the venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adjusts the names of the boards and SoMs to the official naming
used by Kontron marketing. These changes also affect devicetree
names and compatibles. The same changes have been submitted to the
Linux kernel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The new stable configuration is missing the 100mt setpoint, remove
it before updating the config to make sure the changes are separated
cleanly.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable the redundant environment feature to allow falling back in case of
storage corruption. The partition layout for the SPI NOR device is added
to the devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The display isn't and won't be used in U-Boot. Also the display setup
is not yet supported in mainline Linux, so even for cases where the
U-Boot devicetree is passed to the kernel there is currently no use
for this configuration.
Selecting the proper configuration in the kernel FIT image automatically
depending on the detected hardware can be handled by a script in the
environment.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc0008011 "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Trying to load U-Boot proper from SPL when SPL was not loaded from
SD-Card is currently not working because the SDMMC pins aren't muxed
correctly. It is assumed the BootROM is doing this for us when booting
from SD-Card hence why it's not needed when booting TPL/SPL from
SD-Card.
The pinctrl properties are removed from the SPL DT property removal list
and the pinctrl configuration nodes made available in the SPL DT, in
addition to the pull-up configurations to allow loading U-Boot proper
from SD-Card as a fallback mechanism for SPI-NOR and eMMC.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.
Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1 work in otg mode
- 12V DC Power supply
The dts file is sync from linux-next[0].
[0]:https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Partial sync of rk3288.dtsi from Linux version 5.18
Changed:
only properties and functions that are not yet included
swap some clocks positions
fix some irq numbers
style and sort nodes
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version update the cpu and gpu nodes.
Changed:
use operating-points-v2
update thermal for all cpus
add labels to all cpus
change gpu compatible
change gpu interrupt names
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move thermal sub nodes to the dtsi
file and remove rk3288-thermal.dtsi
Changed:
replace underscore in nodename
remove comments about sensor and ID
use gpu phandle
add #cooling-cells to gpu node
lower critical temparature
remove linux,hwmon property
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move to latest DDR4 1600MT/s for k3-am64-evm based on EMIF tool
v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Move k3-am64-sk to use 1600MT/s LPDDR4 configuration and update to latest EMIF
tool v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 32-bit SoCs, from arch/arm/boot/dts/.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
The R40 boards gain DVFS support.
Some A23/A33 tablet DTs are unified into a single file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
Some A64 boards gain some audio nodes.
The H616 DTs are now switched to the version finally merged into the
kernel, which brings some changes, but none affecting U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The PWR regulators don't need be removed as they are already deactivated.
This patches is a alignment with the accepted patch in Linux device tree
in commit a34b42f8690c ("ARM: dts: stm32: fix pwr regulators references
to use scmi").
Fixes: 69ef98b209 ("ARM: dts: stm32mp15: alignment with v5.19")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix the frequencies listed in PLL configuration comments to match
the actual frequencies programmed into hardware. Furthermore, add
a comment which explains how those frequencies are calculated, so
it won't be necessary to look it up all over the datasheet and
make more mistakes in the calculation in the future.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add DT for DHCOR Testbench board, which is a testbench for testing of
DHCOR SoM during manufacturing. This is effectively a trimmed down
version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and
LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3
is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM
variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the regulator-always-on is present in regulator DT node,
the regulator is always reconfigured to the voltage set in DT on
probe, even if regulator_set_value() has been called before. Drop
the property from AV96 U-Boot DT and enable the regulator manually
in code, as the board already reconfigures the Buck3 regulator in
code per PMIC NVM content instead.
Fixes: 0adf10a87b ("ARM: dts: stm32: Configure Buck3 voltage per PMIC NVM on Avenger96")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
These boards are out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When the imx8mn.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
When the imx8mn.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
-----BEGIN PGP SIGNATURE-----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=iA80
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Device tree alignment with kernel v6.0-rc4.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
The input clock for uart is too slow (25MHz) which introduces frequent data
error on both receiving and transmitting even if the baudrate is 115200.
Using high-speed can significantly solve this issue.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7981 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds basic support for MediaTek MT7986 SoC.
This include the file that will initialize the SoC after boot and its
device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Remove the unnecessary nodes for TFABOOT and keep the mandatory part
in SOC dtsi, only the DDRCTRL and DDRPHY addresses.
This patch allows to manage the DDR configuration setting in U-Boot
device tree only if it is needed, when CONFIG_SPL is defined.
With TFABOOT, the DDR configuration is done in TF-A BL2 and the DDR size
is dynamically computed in U-Boot since commit d72e7bbe7c ("ram:
stm32mp1: compute DDR size from DDRCTL registers").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TI DP83867 is using strapping based on MIO pins. Tristate setup can influce
PHY address. That's why switch description with ethernet-phy-id compatible
string which enable calling reset. PHY itself setups phy address after
power up or reset. Reset description will be added in separate commit.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/52bf9ac0453d4e4896d8edd2618e684bb1ff6012.1662721547.git.michal.simek@amd.com
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: 24a7a3c1c0 ("imx8mm: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The upstream Linux DSA drivers do not require phy-handle nodes in
the DSA ports yet the U-Boot DSA drivers do. Add a phy-handle and
the mdio nodes to the u-boot.dtsi file so that future dts file
syncrhonization between Linux and U-Boot don't break networking.
Fixes: e0caa84ca6 ("imx8mp: synchronise device tree with linux")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Adding the "u-boot,dm-pre-reloc" DT property to the timer node is
necesssary to support the timer in the early boot phases (e.g.
SPL & pre-reloc).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Add the DT bindings / descriptions for timer0 & timer1, exactly as done
in mainline Linux.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch changes the compilation, so that the Armada 375 board(s) are
compiled in a separate step. This is necessary for the timer dts
conversion, as A375 has a different / timer description in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
With the recent changes in the Marvel mvneta network driver, the MDIO
bus is not connected any more. This patch updates the DT nodes to use
the nodes from the dtsi files instead of creating ad-hoc nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch makes sure that the Devicetree for the sama7
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This patch makes sure that the Devicetree for the sama5
boards are aligned with the Devicetree from Linux. This
implies removing the GPIO compatible and replacing it
with the PINCTRL one, as well as unifying the SDMMC
pinctrl related subnodes under one single subnode.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Fix copy-paste error of the I2C5 bus recovery GPIO assignment,
the I2C5 GPIOs are on gpio3 instead of gpio5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
The ECSPI1 is on I2C1/I2C2 pins of the SoC, update the pinmux accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Rename imx8mp-dhcom-pdk2-u-boot.dtsi to imx8mp-dhcom-u-boot.dtsi, since
this file is shared by PDK2, PicoITX and DRC02. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Add information about which exact SoM variant is used on which PDK2 variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Adam Ford <aford173@gmail.com>
The NXP i.MXRT1170 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 and Cortex-M4 core.
The EVK provides 64 MB SDRAM, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
SDRAM
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
* Remove unnecessary device tree nodes which are not needed in
U-Boot directly.
* Move all U-Boot specific device tree properties to u-boot dtsi.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Commit 6337d53fdf ("arm: dts: sync am33xx with Linux 5.9-rc7") syncs
the am335x device tree with the latest linux kernel am335x device tree.
That causes problems with device tree in SPL stage.
To fix the issues CONFIG_SPL_OF_TRANSLATE must be set to handle the
synced bus addresses correctly.
A custom U-Boot device tree is also needed since the SPL build removes
bus properties from bus nodes which are not explicitly marked with the
u-boot,dm-spl or u-boot,dm-pre-reloc flag. Therefore all parent buses of
the in the SPL needed devices must be marked with u-boot,dm-pre-reloc.
Also since there is no driver for "ti,sysc" compatible property in SPL
the buses marked with this compatible string must also be marked with
compatible = "simple-bus" to make the underlying devices visible in
SPL. Otherwise the matching device drivers aren't found and the uclass
drivers are dropped.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Added ref_clk 'ref' property for GUCTL_REFCLKPER and GFLADJ_REFCLK_FLADJ
calculation. This property configure correct value for SOF/ITP counter
and period of ref_clk.
This patch adds 'ref' property for both dwc3_0 and dwc3_1 cores.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/417545b948ea12a9301a5e80851f98523be2b443.1661259809.git.michal.simek@amd.com
Update MTD partitions of Kria device trees to allocate 128KB of QSPI
memory for secure OS. Increased "SHA256" partition size & changed
starting address of "User" partition to accommodate the new partition
"Secure OS Storage"
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9cc64b8c731d11439de73d0af54c65080068f00b.1661242681.git.michal.simek@amd.com
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Removes hwlocks properties from stm32mp151 pinctrl node. These locks
could be used for other purpose, depending on board and software
configuration hence do not enforce their use to protect pinctrl
devices.
This patch is an alignment with Linux device tree with v6.0 as the
hwsem support wasn’t yet added in pincontrol in kernel. It avoids
issues when the Linux kernel is started with the U-Boot device tree.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit ef4ce6df32 "video: stm32: stm32_ltdc: fix data enable polarity"
The panel display output wasn't functional anymore.
Device tree display-timings de-active property value must be updated
to 1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This new image is similar to u-boot-rockchip.bin except that it's
destined to be flashed on SPI-NOR flashes.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prepares for the creation of a u-boot-rockchip-spi.bin image
similar to u-boot-rockchip.bin to the exception it's destined for
SPI-NOR flashes instead of MMC storage medium.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
idbloader.img content - currently created by way of Makefile - can be
created by binman directly.
So let's do that for Rockchip ARM platforms.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot_devices constants for rk3288 were changed to match the
binding, but the dtsi file was not synced.
Fix by renaming the rk3288 mmc node names.
Also correct the clock name for "ciu-drive".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the Generic Names Recommendation in the Devicetree
Specification Release v0.3, and the DT Bindings for the Renesas Reduced
Pin Count Interface, the node name for a Renesas RPC-IF device should be
"spi". Especially on R-Car Gen3 and RZ/G2, the node name matters, as
the node is enabled by passing a DT fragment from TF-A to U-Boot, and
from U-Boot to subsequent software.
Fix this by renaming the device nodes from "rpc" to "spi".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC provides support for two USB controllers: one USB3 and the
other one being USB2. The USB3 controller supports further 2 PHY: one high
speed PHY and the other super speed PHY. The USB2 controller supports a
single high speed PHY. So add corresponding DT nodes.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
The board has only one network interface. The linux kernel will
gracefully skip a the ethernet interface if no connected PHY could be
probed. u-boot on the other hand will throw an error message. The kernel
device tree is about to be fixed. For now, just disable the ethernet
interface in our -u-boot.dtsi.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
pcm051_rev3_defconfig config (Phytec Wega board) has been dropped in
64efd11d ("arm: Remove pcm051 board")
due to expired migration deadlines. Here, pcm051_rev3_defconfig support is
reintroduced.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
caam driver model enabled in spl for secure boot.
fsl_rsa_mod_exp driver enabled in spl for validating uboot image.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Replace code that accessed the GPIO registers directly with code that
makes use of the LED_GPIO driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-38x-controlcenterdc-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move U-Boot specific device tree property u-boot,dm-pre-reloc into U-Boot
specific device tree include file armada-xp-theadorable-u-boot.dtsi.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Replace it by including of mvebu-u-boot.dtsi file. When board does not use
-u-boot.dtsi then mvebu-u-boot.dtsi is included automatically by makefile
scripts/Makefile.lib.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Set u-boot,dm-pre-reloc for /soc/, /soc/internal-regs/ and &uart0 nodes as
it is required on every 32-bit Armada SoCs. And set also u-boot,dm-pre-reloc
for &spi0 when going to boot from SPI because otherwise SPL SPI drivers do
not load.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
64-bit Armada DTS files are not build correctly during compilation of
32-bit Armada boards and vice versa. So fix makefile build system to
compile only those dts files which are compatible for the current build
(64-bit Armada DTS files only for 64-bit builds and 32-bit Armada DTS files
only for 32-bit builds).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
UniPhier LD20, PXs2 and PXs3 boards have ethernet phy that has RX/TX delays
of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
So should set the phy-mode to "rgmii-id" to show that RX/TX delays are
enabled.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Signed-off-by: Marek Behún <kabel@kernel.org>
* Add SPDX-License-Identifier
* Add SFP and LED nodes
* Fix PHY nad NOR nodes
* Remove duplicates from u-boot.dtsi file
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows U-Boot mvebu-gpio.c driver to switch particular MPP pin into
GPIO mode and enable GPIO support.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
After we switch to use BINMAN_SYMBOLS, there is no need to pad
the file size to 0x8000 and 0x4000. After we use BINMAN_SYMBOLS,
the u-boot-spl-ddr.bin shrink about 36KB with i.MX8MP-EVK.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
We are migrating to use binman symbols, the current names are
inconsistent across different boards, so unify them.
Also add `type = "blob-ext";`, since the new names are not valid binman
types.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Edit commit message]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add the DTSi file and DT header files for i.MX93 SoC
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Qualcomm device trees in U-Boot are currently not consistent with
the upstream DTs used in the Linux kernel. While some bindings are
similar to the official specification in the Linux kernel, several
nodes have subtle differences, e.g. the "compatible"s or the exact
specification of memory registers.
This means that some of the Qualcomm-related U-Boot drivers are not
compatible with the Linux DT (and vice versa).
The SPMI node is one such example: the "core" region starts at
0x0200f000 in the upstream Linux MSM8916 DT, but in U-Boot it starts at
0x0200f800. The end result is normally the same, since the Linux SPMI
driver simply adds the 0x800 internally.
However, commit f5a2d6b4b0 ("spmi: msm: add arbiter version 5
support") imported this behavior into the U-Boot driver, without
adjusting the DB410c/DB820c device trees. This means that the 0x800
offset is now added twice, breaking all SPMI read/write operations:
Failed to find PMIC pon node. Check device tree
Failed to find pm8916_gpios@c000 node.
USB init failed: -6
starting USB...
Bus ehci@78d9000: Failed to find pm8916_gpios@c000 node.
probe failed, error -6
No working controllers found
While the mistake is strictly speaking in the spmi-msm driver, fix the
issue by making the SPMI nodes in the DB410c/DB820c consistent with the
upstream Linux DT instead.
Ideally we should even go a step further by fixing the remaining uses
of custom bindings in the U-Boot drivers and moving to using the Linux
DTs as-is. This would likely avoid such mistakes in the future and
would also make the porting process much easier.
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Fixes: f5a2d6b4b0 ("spmi: msm: add arbiter version 5 support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Currently u-boot running on mt7622 will print an warning log at beginning:
> serial_mtk serial@11002000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
It turns out that the pinctrl uclass can't work properly in board_f stage.
Since the uart0 is the default UART device used by bootrom, and will be
initialized in both bootrom and tf-a bl2. It's ok not to setup pinctrl for
uart0 in u-boot.
This patch removes the default pinctrl of uart0 to suppress the unwanted
warning.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The entry for DDRSS_PI_321_DATA was accidentally repeated leading to the
last few PI registers being incorrectly programmed.
Fix this.
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Configure debug UART pins as function: "qup9" rather than being regular
gpios. It fixes a hang seen during pinmux setting.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than using magic numbers as clock ids for peripherals import
qcom,gcc-sdm845.h from Linux to be used standard macros for clock ids.
So start using corresponding clk-id macro for debug UART.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
According to u-boot DT recomendation, u-boot specific DT properties belong
to *-uboot.dtsi. Also for starqltechn board (which is the only current
consumer of sdm845.dtsi), the properties are already included in
starqltechn-uboot.dtsi, so remove corresponding redundant properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently there is a mismatch among DT node overrides in starqltechn
board DTS file and the actual DT nodes in the sdm845.dtsi. So fix that
to align with DT nodes in sdm845.dtsi.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@0:pwms: property size (12) too small for cell size 3
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@1:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb).
Please further note that the PMIC node name got changed from a pmic
label to pmic@25 which required adjustment in resp. board SPL file
board/toradex/verdin-imx8mm/spl.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the pinctrl_pmic reference which does not
exist in the Linux upistream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx8mm-venice-gw700x-u-boot.dtsi:26.1-14 Label or
path pinctrl_pmic not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
vf610-colibri-eval-v3.dtb rather than the previous vf610-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the included SoC dtsi from vf.dtsi to
vf610.dtsi as this is how it is named in Linux upstream.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
