default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add PHY_CORTINA as default option in SYS_MMC_ENV_DEV Kconfig entry as
PHY_CORTINA require SYS_MMC_ENV_DEV value similar to FMAN_ENET or QE.
This helps in resolving compilation failure.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently, the environment is always stored in eMMC if eMMC is enabled
in the config. This means images written to SD and eMMC will cross-
contaminate their environments unless the configuration is changed.
By dropping the device number from the environment location string and
implementing mmc_get_env_dev, we will always use the environment from
the boot device when booting from SD/eMMC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This variable is used for pointing to location where redundant variables
are located. There is no default value. And it doesn't need to be specified
which is showing as warning when savedefconfig is called.
make xilinx_zynqmp_virt_defconfig
#
# configuration written to .config
#
make savedefconfig
scripts/kconfig/conf --savedefconfig=defconfig Kconfig
.config:199:warning: symbol value '' invalid for ENV_OFFSET_REDUND
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As the the SPI flash is probed and is released in each ENV sf function
the env_flash no more need to be static.
This patch move this device handle as local variable of each function and
simplify the associated code (env_flash is never == NULL when
setup_flash_device is called).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Free the SPI resources by calling spi_flash_free() in each env sf
function to avoid issue for other SPI users.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support of opts erase for env in SPI flash;
this opts is used by command 'env erase'.
This command only fills the env offset by 0x0 (bit flip to 0) and
the saved environment becomes invalid (with bad CRC).
It doesn't erase the sector here to avoid issue when the sector
is larger than the env (i.e. embedded when
CONFIG_ENV_SECT_SIZE > CONFIG_ENV_SIZE).
The needed sector erase will be managed in the next "env save" command,
using the opt ".save", before to update the environment in SPI flash.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add ENV_ERASE_PTR macro to handle erase opts and remove the associated
ifdef.
This patch is a extension of previous commit 82b2f41357 ("env_internal.h:
add alternative ENV_SAVE_PTR macro").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This fixes the case where there are multiple environment drivers, one of
them is the default environment one, and it is followed by an environment
driver which does not implement .init() callback. The default environment
driver sets gd->env_valid to ENV_INVALID and returns 0 from its .init()
callback implementation, which is valid behavior for default environment.
Since the subsequent environment driver does not implement .init(), it
also does not modify the $ret variable in the loop. Therefore, the loop
is exited with gd->env_valid=ENV_INVALID and ret=0, which means that the
code further down in env_init() will not reset the environment to the
default one, which is incorrect.
This patch sets the $ret variable back to -ENOENT in case the env_valid
is set to ENV_INVALID by an environment driver, so that the environment
would be correctly reset back to default one, unless a subsequent driver
loads a valid environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Since commit 0f036bf4b8 ("env: Warn on force access if ENV_ACCESS_IGNORE_FORCE set")
a warning message is displayed when setenv -f is used WITHOUT
CONFIG_ENV_ACCESS_IGNORE_FORCE, but the variable is set anyway, resulting
in lots of log pollution.
env_flags_validate() returns 0 if the access is accepted, or non zero
if it is refused.
So the original code
#ifndef CONFIG_ENV_ACCESS_IGNORE_FORCE
if (flag & H_FORCE)
return 0;
#endif
was correct, it returns 0 (accepts the modification) if forced UNLESS
IGNORE_FORCE is set (in which case access checks in the following code
are applied). The broken patch just added a printf to the force accepted
case.
To obtain the intent of the patch we need this:
if (flag & H_FORCE) {
#ifdef CONFIG_ENV_ACCESS_IGNORE_FORCE
printf("## Error: Can't force access to \"%s\"\n", name);
#else
return 0;
#endif
}
Fixes: 0f036bf4b8 ("env: Warn on force access if ENV_ACCESS_IGNORE_FORCE set")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
If one of the reads fails when importing redundant environments (a
single read failure), the env_flags wouldn't get initialized in
env_import_redund(). If a user then calls saveenv, the new environment
will have the wrong flags value. So on the next load the new environment
will be ignored.
While debugging this, I also noticed that env/sf.c was not correctly
handling a single read failure, as it would not check the crc before
assigning it to gd->env_addr.
Having a special error path for when there is a single read failure
seems unnecessary and may lead to future bugs. Instead collapse the
'single read failure' error to be the same as a 'single crc failure'.
That way env_check_redund() either passes or fails, and if it passes we
are guaranteed to have checked the CRC.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is roughly the U-Boot side equivalent to commit
e282c422e0 (tools: fw_env: use erasesize from MEMGETINFO ioctl). The
motivation is the case where one has a board with several revisions,
where the SPI flashes have different erase sizes.
In our case, we have an 8K environment, and the flashes have erase
sizes of 4K (newer boards) and 64K (older boards). Currently, we must
set CONFIG_ENV_SECT_SIZE to 64K to make the code work on the older
boards, but for the newer ones, that ends up wasting quite a bit of
time reading/erasing/restoring the last 56K.
At first, I wanted to allow setting CONFIG_ENV_SECT_SIZE to 0 to mean
"use the erase size the chip reports", but that config
option is used in a number of preprocessor conditionals, and shared
between ENV_IS_IN_FLASH and ENV_IS_IN_SPI_FLASH.
So instead, introduce a new boolean config option, which for now can
only be used with ENV_IS_IN_SPI_FLASH. If left off, there's no change
in behaviour.
The only slightly annoying detail is that, when selected, the compiler
is apparently not smart enough to see that the the saved_size and
saved_offset variables are only used under the same "if (sect_size >
CONFIG_ENV_SIZE)" condition as where they are computed, so we need to
initialize them to 0 to avoid "may be used uninitialized" warnings.
On our newer boards with the 4K erase size, saving the environment now
takes 0.080 seconds instead of 0.53 seconds, which directly translates
to that much faster boot time since our logic always causes the
environment to be written during boot.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
As preparation for the next patch, use a local variable to represent
the sector size. No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_REDUNDAND_ENVIRONMENT is changing in env_internal.h how u-boot
works with variables. struct environment_s has one byte flags property
which also affects ENV_SIZE macro.
I have reached the case where CONFIG_ENV_IS_NOWHERE is default setup
but custom scripts can be designed in a way that u-boot is asked to
import/export variables from/to file which can be in certain format.
That's why also for this configuration make sense to enable
CONFIG_SYS_REDUNDAND_ENVIRONMENT because it depends on environment file
format.
The patch is removing dependency on this configuration to support selecting
environment file format without any specific dependency where variables are
stored.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function mmc_offset_try_partition searches the MMC partition for
locating environment data, by comparing the partition names with config
"u-boot,mmc-env-parition". However, it only compares the first word-size
bytes (size of 'const char *'), which may make the function to find
unintended partition.
Correct the function not to partially compare the partition name with
config "u-boot,mmc-env-partition".
Fixes: c9e87ba665 ("env: Save environment at the end of an MMC partition")
Signed-off-by: Hoyeonjiki Kim <jigi.kim@gmail.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Michael wrote:
commit 92765f45bb ("env: Access Environment in SPI flashes before
relocation") at least breaks the Kontron sl28 board. I guess it also
breaks others which use a (late) SPI environment.
reason is, that env_init() sets the init bit, if there
is no init function defined in an environment driver,
and use default return value -ENOENT in this case
later for setting the default environment.
Change:
Environment driver can now implement an init
function and return, if this function does nothing,
simply -ENOENT.
env_init() now handles -ENOENT correct by setting the
inited bit for the environment driver. And if there
is no other environment driver whose init function
returns 0, load than the default environment.
This prevents that each environment driver needs to set the
default environment.
Fixes: 92765f45bb ("env: Access Environment in SPI flashes before relocation")
Reported-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc> [For the SF environment]
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable the new Kconfig option ENV_SPI_EARLY if you want
to use Environment in SPI flash before relocation.
Call env_init() and than you can use env_get_f() for
accessing Environment variables.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
split from env_import_redund() the part which checks
which Environment is valid into a separate function
called env_check_redund() and call it from env_import_redund().
So env_check_redund() can be used from places which also
need to do this checks.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This parallels what I added for FAT in commit 6731bef696, allowing the
environment to be found in a specific partition on the device that the
board's mmc_get_env_dev() returns. On the Banana Pi R2 that means the
device that U-Boot was loaded from; either the internal eMMC or an SD
card.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Since it's so trivial I could just about tolerate this when there were only
two copies of it. But now there are about to be three.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Zynq is similar to ZynqMP u-boot feature wise that's why also enable
default option for ENV_FAT_DEVICE_AND_PART Kconfig entry.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ENV_IS_IN_EXT4 also need to enable FS_EXT4 which is not covered in Kconfig.
Kconfig reports this as:
WARNING: unmet direct dependencies detected for EXT4_WRITE
Depends on [n]: FS_EXT4 [=n]
Selected by [y]:
- ENV_IS_IN_EXT4 [=y] && !CHAIN_OF_TRUST [=n]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option marks any U-Boot variable which does not have explicit 'w'
writeable flag set as read-only. This way the environment can be locked
down and only variables explicitly configured to be writeable can ever
be changed by either 'env import', 'env set' or loading user environment
from environment storage.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration option which prevents the environment hash table to be
ever cleared and reloaded with different content. This is useful in case
the first environment loaded into the hash table contains e.g. sensitive
content which must not be dropped or reloaded.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add another custom environment flag which discerns environment coming
from external storage from environment set by U-Boot itself.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add another internal environment flag which indicates that the operation
is resetting the environment to the default one. This allows the env code
to discern between import of external environment and reset to default.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the ENV_ACCESS_IGNORE_FORCE is set, inform user that the variable
cannot be force-set if such attempt happens.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support of opts erase for env in ext4,
this opts is used by command 'env erase'.
This command only fill the env file (CONFIG_ENV_EXT4_FILE)
with 0, the CRC and the saved environment becomes invalid.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the new command 'env select' to force the persistent storage
of environment, saved in gd->env_load_prio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the new command env load to load the environment from
the current location gd->env_load_prio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ops driver load becomes mandatory in struct env_drive,
change the comment for this ops and remove unnecessary test.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the ops .load for nowhere ENV backend to load the
default environment.
This ops is needed for the command 'env load'
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Only update gd->env_load_prio in generic function env_load()
and no more in the weak function env_get_location() which is
called in many place (for example in env_driver_lookup, even
for ENVOP_SAVE operation).
This patch is a preliminary step to use env_driver_lookup()/
env_get_location() in new function env_select() without
updating gd->env_load_prio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a missing initialization of gd->env_valid in env_ext4_load
as it is already done in some other env device.
Set gd->env_valid = ENV_VALID in env_ext4_save() and env_ext4_load().
This patch allows to have a correct information in 'env info' command.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>