At present there are 3 irq router drivers. One is the common one
and the other two are chipset specific for queensbay and quark.
However these are really the same drivers as the core logic is
the same. The two chipset specific drivers configure some registers
that are outside the irq router block which should really be part
of the chipset initialization.
Now we remove these specific drivers and make all x86 boards use
the common one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This updates all x86 boards that currently have IRQ router in the
dts files to include ACTL register details.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this GPIO driver still uses the legacy PCI API. Now that
we have proper PCH drivers we can use those to obtain the information
we need. While the device tree has nodes for the GPIO peripheral it is
not in the right place. It should be on the PCI bus as a sub-peripheral
of the PCH device.
Update the device tree files to show the GPIO controller within the PCH,
so that PCI access works as expected. This also adds '#address-cells'
and '#size-cells' to the PCH node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present ich spi driver gets the controller version information via
pch, but this can be simply retrieved via spi node's compatible string.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
With recent changes spi node was moved to a place as a subnode under
pch, so update the alias to refer to its correct place as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a driver for interrupts on queensbay and move the code currently in
cpu_irq_init() into its probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present this SPI driver works by searching the PCI buses for its
peripheral. It also uses the legacy PCI API.
In addition the driver has code to determine the type of Intel PCH that is
used (version 7 or version 9). Now that we have proper PCH drivers we can
use those to obtain the information we need.
While the device tree has a node for the SPI peripheral it is not in the
right place. It should be on the PCI bus as a sub-peripheral of the LPC
device.
Update the device tree files to show the SPI controller within the PCH, so
that PCI access works as expected.
This patch includes Bin's fix-up patch from here:
https://patchwork.ozlabs.org/patch/569478/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With recent ns16550 driver changes, we only changed the legacy UART
(at I/O port 0x3f8) compatible string, but forgot to change the PCI
UART compatible string. Now fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In order to make a pci uart device node to be properly bound to its
driver, we need make sure its parent node has a compatible string
which matches a driver that scans all of its child device nodes in
the device tree.
Change all pci bridge nodes under root pci node to use "pci-bridge"
compatible driver, as well as corresponding <reg> properties to
indicate its devfn. At last, adding "u-boot,dm-pre-reloc" to each
of these nodes for driver model to initialize them before relocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 4 usb ports on the Intel Crown Bay board, 2 of which are
connected to Topcliff usb host 0 and the other 2 connected to usb
host 1. USB devices inserted in the ports connected to usb host 1
cannot get detected due to wrong IRQ assigned to the controller.
Actually we need apply the PCI interrupt pin swizzling logic to all
devices on the Topcliff chipset when configuring the PIRQ routing.
This was observed on usb ports, but device 6 and 10 irqs are also
wrong. Correct them all together.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since Intel ICH SPI driver has been converted to driver model, we need
add an alias for SPI node in the board dts files otherwise SPI flash
won't be detected due to 'invalid bus' error.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Topcliff PCH has 4 UART devices integrated (Device 10, Funciton
1/2/3/4). Add the corresponding device nodes in the crownbay.dts per
Open Firmware PCI bus bindings.
Also a comment block is added for the 'stdout-path' property in the
chosen node, mentioning that by default the legacy superio serial
port (io addr 0x3f8) is still used on Crown Bay as the console port.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commits cleans up the board dts files.
- Correct the serial port register size to 8
- Remove the misleading status = "disabled" statement in the
serial.dtsi
- Move the inclusion of skeleton.dtsi from serial.dtsi to board
dts files
- Let the board dts file define stdout-path in the chosen node
- Remove device nodes in board dts files thar are duplicated to
skeleton.dtsi
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The name of coreboot.dtsi is misleading, as it actually describes
the legacy serial port device node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
To avoid having two microcode formats, adjust the build system to support
obtaining the microcode from the device tree, even in the case where it
must be made available before the device tree can be accessed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
