Commit graph

86 commits

Author SHA1 Message Date
Niel Fourie
6e171b661e ARM: am335x: Add phyCORE AM335x R2 support
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")

Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
2019-07-13 11:11:28 -04:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Parthiban Nallathambi
d2d1191843 imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.

CPU:   Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM:  256 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial@02020000
Out:   serial@02020000
Err:   serial@02020000
Net:   FEC0

Working:
 - Eth0
 - i2C
 - MMC/SD
 - eMMC
 - UART (1 & 5)
 - USB (host & otg)

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
2019-06-11 10:42:48 +02:00
Parthiban Nallathambi
a443c8212c ARM: dts: i.MX6ULL: U-Boot specific dts for u-boot, dm-spl
u-boot,dm-spl property is specific to U-Boot, so created one
for i.MX6ULL platforms.

Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
2019-06-11 10:42:48 +02:00
Lukasz Majewski
bdc9fefcbf pcm052: bk4: Add board_phy_config() for BK4 to setup ksz8081 phy
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
15a4456903 pcm052: mac: Provide board specific imx_get_mac_from_fuse() function
This commit introduces the board specific function to read fused mac
address.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
379255f1ee pcm052: board: Add code to setup LED default states
As one has moved to DM based LEDs, this code is required to setup the
default state.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
e5b345f30c pcm052: bk4: sdcard: Add support for SD card booting/recovery
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
27e15e533c pcm052: board: Remove in-board setup code (it is now replaced by DM setup)
This commit cleans up the pcm052.c file to remove dead code after moving to
DTS and DM.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
fbe114aa4b pcm052: board: cosmetic: Add copyright notice to pcm052.c
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
5f1588acc2 pcm052: board: vybrid: Update the board name for BK4 device
This commit provides distinction between PCM052 and BK4.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
fea63a5d7d pcm052: board: Remove "m4go" command as it is superseded by "bootaux"
The "m4go" provides exactly the same functionality as the IMX generic
"bootaux" command. Remove it to not duplicate the code.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13 20:30:08 +02:00
Lukasz Majewski
bc51c91120 pcm052: board: Do not enable I2C2 code in the board file
As the I2C2 clock is now enabled in the generic clock code, we can remove
this code from a board file.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Martyn Welch
0963060c99 imx: Add PHYTEC phyBOARD-i.MX6UL-Segin
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).

CPU:   Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   FEC0

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART (1 & 5)
 - USB (host & otg)

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2019-01-28 12:47:27 +01:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Alex Kiernan
9925f1dbc3 net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08 23:00:58 -04:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Tom Rini
79df00fdb4 MAINTAINERS: Add missing boards and config entries
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time.  As part of that, address a number of
missing MAINTAINERS entires.  In the case of a missing file, I have put
the original submitter down.  In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-06 09:58:51 -05:00
Wadim Egorov
32191a3912 rockchip: phycore: Read configuration EEPROM & set ethaddr in late init
Read SoM information from EEPROM and set ethaddr in late init.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-05 11:04:34 +02:00
Stefano Babic
cb40adff8f pfla02: Fix RAM detection and support 1 bank SOM
In case of 2 banks, the address space of the first CS must be defined
and not let to the higher value.

Add support for SOM with a single bank of RAM. It was tested with i.MX6Q
modules in the following configurations:

- 2 Banks, 4 GB
- 2 Banks, 1 GB
- 1 Bank,  1 GB

Signed-off-by: Stefano Babic <sbabic@denx.de>
2017-08-29 09:46:32 +02:00
Breno Lima
3aa4b703b4 imx: imx6: Move gpr_init() function to soc.c
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28 09:48:53 +02:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Simon Glass
35affd7a2f env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()
Rename this function for consistency with env_get().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:44 -04:00
Simon Glass
fd1e959e91 env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()
Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:56 -04:00
Stefano Babic
83605d37b0 mx6: Add support for Phytec pfla02 (NAND)
Add support for Phytec pfla02, equipped with NAND.

CPU:   Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 31C
Reset cause: POR
I2C:   ready
DRAM:  1 GiB
NAND:  2048 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total
16 MiB
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Stefan Christ <s.christ@phytec.de>
CC: Stefan Müller-Klieser <S.Mueller-Klieser@phytec.de>
CC: Christian Hemp <C.Hemp@phytec.de>
2017-08-02 11:45:27 +02:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Wadim Egorov
bafcf2db41 rockchip: Add basic support for phyCORE-RK3288 SoM based carrier board
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:

  - 1 GB DDR3 RAM (2 Banks)
  - 1x 4 KB EEPROM
  - DP83867 Gigabit Ethernet PHY
  - 16 MB SPI Flash
  - 4 GB eMMC Flash

Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 15:23:38 +02:00
Heiko Schocher
064b55cfcb powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-16 10:14:55 -04:00
Simon Glass
fc843a02ac Kconfig: Add a CONFIG_IDE option
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.

Update existing users and move the ide driver into drivers/block since
it should not be in common/.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 12:45:27 -04:00
Tom Rini
b3cf43392a pcm058: Fix unused variable warnings
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
add a gaurd.  The variable gpio_pads is never referenced, drop it.  The
variable usdhc4_pads are only referenced when we do not have
CONFIG_CMD_NAND set and we are not doing an SPL build, modify the
existing guard.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-12 08:37:27 -04:00
Simon Glass
f1683aa73c board_f: Rename initdram() to dram_init()
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 09:40:57 -04:00
Simon Glass
088454cde2 board_f: Drop return value from initdram()
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:59:20 -04:00
Simon Glass
52c411805c board_f: Drop board_type parameter from initdram()
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 13:58:44 -04:00
Stefan Agner
7966b43778 ARM: vf610: move to standard arch/board approach
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19 17:30:11 +01:00
Albert ARIBAUD \(3ADEV\)
db74cbfc09 pcm052: fix DDR initialization sequence
The sequence erroneously launched the DDR controller
initialization before the pad muxing was done, causing
DRAM size computation to hang.

Configuring the pads first then launching DDR controller
initialization prevents the DRAM hanging.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2017-02-08 16:24:25 -05:00
Jagan Teki
03bf9d58b9 imx: s/docs\/README.imximage/doc\/README.imximage/g
Fixed typo for doc/README.imximage on respective imximage.cfg files.

Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Albert ARIBAUD \(3ADEV\)
27192d16eb pcm052: add new BK4r1 target based on PCM052 SoM
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:22:11 +02:00
Albert ARIBAUD \(3ADEV\)
a7e5f7f3e5 pcm052: allow specifying onboard DDR size in configs
PCM052 SoMs may be equipped with various sizes of DDR.
Keep default of 256MB; new PCM052-based targets will
specify their actual DDR size.

Linux command line is auto-adjusted to DDR size.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:06:16 +02:00
Albert ARIBAUD \(3ADEV\)
303a24435f pcm052: add 'm4go' command
Add the 'm4go' command to pcm052-based targets.
It loads scatter file images.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:06:16 +02:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Fabio Estevam
edf0093732 mx6: ddr: Allow changing REFSEL and REFR fields
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.

Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:

$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4      0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800

So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.

Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06 18:22:48 +02:00
Stefano Babic
876a25d289 mx6: Add Phytec PCM058 i.MX6 Quad
Add Phytec-i.MX6 SOM with NAND

  Support:
   - 1GB RAM
   - Ethernet
   - SPI-NOR Flash
   - NAND (1024 MB)
   - external SD
   - UART

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12 17:58:48 +02:00
Robert P. J. Day
7ffe3cd62e Delete tests of CONFIG_OF_LIBFDT when testing CONFIG_OF_BOARD_SETUP
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:

  config OF_BOARD_SETUP
          bool "Set up board-specific details in device tree before boot"
          depends on OF_LIBFDT
          ...

remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:16 -04:00
Albert ARIBAUD \(3ADEV\)
931a1d2a14 vf610: add support for Phytec PCM052
Devices supported are:
- NFC (NAND FLASH)
- MMC
- QSPI (SPI NOR FLASH)
- I2C (only bus 2)
- I2C RTC
- I2C EEPROM
- FEC

Patch-series: 2
- remove useless CONFIG_SYS_SPD_BUS_NUM from config
- remove include of config_cmd_default.h
- remove duplicate CONFIG_CMD_NET

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-10-02 10:42:59 +02:00
Paul Kocialkowski
95de1e2f26 usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-05 17:20:34 +02:00
Joe Hershberger
0adb5b761f net: cosmetic: Name ethaddr variables consistently
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:32 -06:00
Masahiro Yamada
58d423b88e dm: select CONFIG_DM* options
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax.  (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason.  Actually,
for CONFIG_DM*, we have no good reason to do so.

Generally, CONFIG_DM is not a user-configurable option.  Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it.  Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.

Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.

This commit prefers "select" and cleans up the following issues.

[1] Never use "CONFIG_DM=n" in defconfig files

It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set".  But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird.  Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.

[2] Delete redundant CONFIGs

Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-04-18 11:11:30 -06:00
Masahiro Yamada
d648964fc2 kconfig: remove unneeded dependency on !SPL_BUILD
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-24 17:06:27 -05:00
Simon Glass
001646c478 dm: omap3: Move driver model CONFIGs to Kconfig
Remove driver model CONFIGs from the board config headers and use Kconfig
instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 10:35:35 -07:00
Simon Glass
e895a4b06f fdt: Allow ft_board_setup() to report failure
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.

Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.

Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-11-21 04:43:15 +01:00