Commit graph

17 commits

Author SHA1 Message Date
Fabio Estevam
f28e26951a configs: Remove unused symbol CONFIG_DISCOVER_PHY
CONFIG_DISCOVER_PHY is not used anywhere, so remove it from config files.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-08-09 22:32:05 +02:00
Troy Kisky
de6f604de2 mxc_i2c: specify i2c base address in config file
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-11 10:54:29 +02:00
Fabio Estevam
bd6f402b2a mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-07-07 14:07:28 +02:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Tom Rini
26750c8aee CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>
2012-06-20 20:26:16 +02:00
Tom Rini
1005ccfda4 include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
This define does not control anything, remove it.

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:28 +02:00
Stefano Babic
2f002eceae MX35: mx35pdk: wrong board revision
The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:

CPU:   Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0

The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).

Move the output in the board_late_init(), when
pmic can be accessed.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Stefano Babic
0792a36efb mx35: mx35pdk: fix when cache functions are linked
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Stefano Babic
40f6fffee5 MX: serial_mxc: cleanup removing nasty #ifdef
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
2011-12-06 23:59:40 +01:00
Fabio Estevam
d28d6a9619 mx35pdk: Add RTC support
MX35PDK has an MC13892 PMIC. Add RTC support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
2011-11-03 22:56:19 +01:00
Wolfgang Denk
87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00
Helmut Raiger
9660e442de cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover

 #define BOARD_LATE_INIT		1

and adds some basic documentation for board specific
callbacks in README.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-10-27 23:53:59 +02:00
Stefano Babic
5213d6e48e MX35: mx35pdk: use new pmic driver
Switch to new pmic generic driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-10-27 21:56:31 +02:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Stefano Babic
a4adedd439 MX35: mx35pdk: make use of GPIO framework
Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-09-04 11:36:12 +02:00
Stefano Babic
6b5acfc121 MX35: MX35PDK: support additional RAM on CSD1
Modules on mx35pdk have additional 128MB
memory connected to CSD1.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-09-04 11:36:11 +02:00
Stefano Babic
eae4988b45 Add support for Freescale's mx35pdk board.
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02 00:54:43 +01:00