We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a few cases the error handling is not quite right. Make sure we
return the actual error in distro_efi_read_bootflow_file() rather than
-EINVAL. Return -IO when a file cannot be read. Also show the error name
if available.
This does not change operation, but does make it easier to diagnose
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
This causes crashes on some boards, e.g. rockpro64. In any case, we
should not do it.
Check the usb_started flag to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
At present the code does ide_init() as a separate operation, then calls
device_probe() to copy over the information. We can call ide_init() from
probe just as easily.
The only difference is that using 'ide init' twice will do nothing.
However it already fails to copy over the new data in that case, so the
effect is the same. For now, unbind the block devices and remove the IDE
device, which causes the bus to be probed again. Later patches will fix
this up fully, so that all blk_desc data is copied across.
Since ide_reset() is only called from ide_init(), there is no need to init
the ide_dev_desc[] array. This is already done at the end of ide_init() so
drop this code.
The call to uclass_first_device() is now within the probe() function of
the same device, so does nothing. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the -l flag to indicate whether to report missing uclasses.
Also try to be more helpful when no devices are found. For example, when
we see something 'scsi0' requested and nothing was found, this indicates
that there are no SCSI devices, so show a suitable message.
Move messages out of the low-level functions so that silent operation
is possible.
This means they are never reported unless BOOTSTD_FULL is enabled, since
the -l flag cannot otherwise be set.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This test will block compilation of the entire test suite
on platforms without USB support. Make the extern
"usb_started" conditional on USB host or gadget and
define a dummy flag if neither is enabled.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a way to record the bootdevs used when scanning for bootflows. This is
useful for testing.
Enable this only with BOOTSTD_FULL and do the same for the progress
reporting.
Re-enable and update the affected tests now that we have this feature.
For bootdev_test_order_default() there is no-longer any support for using
the bootdev aliases to specify an ordering, so drop that part of the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not used outside tests. Drop it and rename
bootflow_scan_dev() since it is how we start a scan now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to support scanning a single label, like 'mmc' or 'usb0'. Add
this feature by plumbing the label through to the iterator, setting a
flag to indicate that only siblings of the initial device should be used.
This means that scanning a bootdev by its name is not supported anymore.
That feature doesn't seem very useful in practice, so it is no great loss.
Add a test for bootdev_find_by_any() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we set up the bootdev order at the start, then scan the
bootdevs one by one.
However this approach cannot be used with hunters, since the bootdevs may
not exist until the hunter is used. Nor can we just run all the hunters at
the start, since that violate's U-Boot's 'lazy init' requirement. It also
increases boot time.
So we need to adjust the algorithm to scan by labels instead. As a first
step, drop the dev_order[] array in favour of a list of labels. Update the
name of bootdev_setup_iter_order() to better reflect what it does.
Update some related comments and log messages. Also disable a few tests
until a later commit where we can use them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next priority to be processed.
This works by storing the current priority in the bootflow iterator. The
logic to set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which moves to the next label in a list of labels. This
allows processing the boot_targets environment variable.
This works using a new label list in the bootflow iterator. The logic to
set this up is included in a subsequent commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to hunt for a bootdev label and find the bootdev produced
by the hunter (or already present).
Add a few extra flags so that we can distinguish between "mmc1", "mmc" and
"1" which all need to be handled differently.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are associated with the ethernet boot device but do not match its
uclass name, so handle them as special cases.
Provide a way to pass flags through with the bootdev so that we know
how to process it. The flags are checked by the bootmeths, to ensure that
only the selected bootmeth is used.
While these both use the network device, they work quite differently. It
is common to run only one of these, or to run PXE before DHCP. Provide
bootflow flags to control which methods are used. Check these in the two
bootmeths so that only the chosen one is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths provide a way to load a device tree as well as the base
OS image. Add a way to store this in the bootflow. Update the
'bootflow info' command to show this information.
Note that the device tree is not allocated, but instead is stored at
an address provided by an environment variable. This may need to be
adjusted at some point, but for now it works well and fits in with the
existing distro-boot scripts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all partitions are scanned, whether marked bootable or not.
Use only bootable partitions, defaulting to partition 1 if none is
found.
Signed-off-by: Simon Glass <sjg@chromium.org>
If a disk has a bootable partition we are expected to use it to locate the
boot files. Add a function to find it.
To test this, update mmc1 to have two paritions, fixing up other tests
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes ethernet devices are attached to PCI. Since it is quick to scan,
add this into the ethernet hunter.
Run dhcp to establish the network connection. Drop this from the bootdev
since that is not needed now. Update a log message for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a hunter for MMC. This doesn't do anything at present, since MMC is
currently set up when U-Boot starts. If MMC moves to lazy init then we can
add a hunter function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a hunter for USB which enumerates the bus to find new bootdevs.
Update the tests and speed up bootdev_test_prio() while we are here, by
dropping the USB delays.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to run a bootdev hunter to find bootdevs of a certain type. Add
this to the 'bootdev hunt' command. Test for this are added in a later
patch, since a useful test needs some hunters to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootdevs must be enumerated before they appear. For example, USB
bootdevs are not visible until USB is enumerated.
With standard boot this needs to happen automatically, since we only
want to enumerate a bus if it is needed.
Add a way to define bootdev 'hunters' which can be used to hunt for
bootdevs of a given type. Track which ones have been used and add a
command to list them.
Include a clang work-around which seems to be needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We must call dm_scan_other() after devices from the device tree have been
created, since that function behaves differently if there is no bootstd
device.
Adjust the logic to achieve this.
Also fix the bootflow_system() test which was relying on this broken
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test which checks that two operating systems can be displayed in a
menu, allowing one to be selected.
Enable a few things on snow so that the unit tests build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some operating systems provide a logo in bmp format. Read this in if
present so it can be displayed in the menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the concept of an OS name to the bootflow. This typically includes the
OS name, version and kernel version.
Implement this for the distro and script bootmeths so that it works with
Armbian and older version of Fedora.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use a manual test for the VBE test, so we can make the pytest and the
C unit test work together properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need the U-Boot prefix on the version and in fact it is harmful
since pytest gets confused seeing the U-Boot banner bring displayed when
the version is printed.
Drop the prefix from the string.
We could produce an entirely new string from the component parts, but this
adds to the rodata size and would break the use of version_string as the
only thing which holds this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to mark an image as related to a phase, so we can
easily load all the images for SPL or for U-Boot proper.
Add this to the FIT specification, along with some access functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests currently return 0 when they want to be skipped. Update them to
return -EAGAIN instead, so they are counted as skipped.
A few tests are in two parts, with the latter part being skipped in
certain situations. Split these into two and use the correct condition for
the second part.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a FIT includes some OS requests, U-Boot should process these and add
the requested info to corresponding subnodes of the /chosen node. Add a
pytest for this, which sets up the FIT, runs bootm and then uses a C
unit test to check that everything looks OK.
The test needs to run on sandbox_flattree since we don't support
device tree fixups on sandbox (live tree) yet. So enable BOOTMETH_VBE and
disable bootflow_system(), since EFI is not supported on
sandbox_flattree.
Add a link to the initial documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid duplicating code, create a new fit_util module which provides
various utility functions for FIT. Move this code out from the existing
test_fit.py and refactor it with addition parameters.
Fix up pylint warnings in the conversion.
This involves no functional change.
Signed-off-by: Simon Glass <sjg@chromium.org>
This information needs to be set up by the bootstd tests as well. Move it
into a common function and ensure it is executed before any bootstd test
is run.
Make sure the 'images' parameter is set correctly for fixups.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a number of users that use uclass_first_device to access the
first and (assumed) only device in uclass.
Some check the return value of uclass_first_device and also that a
device was returned which is exactly what uclass_first_device_err does.
Some are not checking that a device was returned and can potentially
crash if no device exists in the uclass. Finally there is one that
returns NULL on error either way.
Convert all of these to use uclass_first_device_err instead, the return
value will be removed from uclass_first_device in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function turns out to be a little confusing since it looks up a path
and also registers the tree. Split it into two, one that gets the root
node and one that looks up a path, so the purpose is clear.
Registering the tree will happen in a function to be added in a later
patch, called oftree_from_fdt().
Signed-off-by: Simon Glass <sjg@chromium.org>
