The AXP PMICs have the ability to power off the system. The existing
code for this is duplicated for each PMIC variant, and uses the legacy
non-DM "pmic_bus" interface. When SYSRESET is enabled, this can all be
replaced with a sysreset device using the DM_PMIC interface.
Since the trigger bit is the same on all PMIC variants, use the register
definitions from the oldest supported PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove pmic_max8997/8 files about no-DM.
There are already existed max8997/8 as driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds basic register access and child regulator binding
for the Monolithic MP5416 Power Management IC which integrates
four DC/DC switching converters and five LDO regulators.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
The I2C address is 0x25, not 0x35. This according to the datasheet and
tests with a PCA9450A.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Quoting Ye Li from NXP:
"We have confirmed with PMIC team, 0x35 is used only on early chips
and not used any more. 0x25 is the final address."
Fix it by merging power_pca9450a_init and power_pca9450b_init into one
function power_pca9450_init.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases U-Boot runs the same binary on different board versions.
In wandboard, for example, there are versions with the PFUZE100 PMIC
populated and others without it.
When the PMIC is not present, it is not really useful to get PMIC error,
so change the error message level to debug instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
TPS65941 can have child devices under it (like the ESM support), so
probe these once the master pmic node completes probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently reads the uclass's private data in the ofdata_to_platdata
method which is not allowed, since the uclass has not read it from the
device tree. This happens in the probe method.
Fix it by adding a probe() method and moving the code there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
PCA9450 PMIC series is used to support iMX8MM (PCA9450A) and
iMX8MN (PCA9450B). Add the PMIC driver for both PCA9450A and PCA9450B.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
SYR82X and SYR83X are almost identical to FAN53555, the only difference
is different die ID and revision, voltage ranges and steps.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
The RK809 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(5*BUCKs, 9*LDOs, 2*SWITCHes)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK817 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1* BOOST, 9*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK805 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 3*LDOs)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK816 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1*BOOST, 6*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use MISC u-class to export the NVM register (starting at 0xF8 offset)
and avoid specific API.
- SHADOW have offset < 0.
- NVM have register > 0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
