The command "reginfo" got an overhaul for the ppc4xx. It dumps all the
relevant HW configuration registers (address, symbolic name, content).
This allows to easily detect errors in *.h files and changes in the HW
configuration.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Here you find all the changes in the include directory for new register names
and adapting other ones to the names used by AMCC in their manuals, e.g.
For 440EPx/GRPPC440EPx/GRX, Revision 1.15 – September 22, 2008
For PPC405GP Embedded Processor, Revision 1.02 – March 22, 2006
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Unfortunately some Rev D PPC405EX/405EXr PVR's are identical with older
405EX(r) parts. Here a list:
0x12911475 - 405EX Rev D with Security *and* 405EX Rev A/B witout Sec
0x12911473 - 405EX Rev D without Security *and* 405EXr Rev A/B with Sec
Since there are only a few older parts in the field, this patch now
changes the PVR's above to represent the new Rev D versions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phong Vo" <pvo@amcc.com>
This message is printed upon PCIe bus scan, not only upon error, but also
if no PCIe device is detected at all. Since this is not an error, let's
remove this message in this case. We already have the message
"link is not up." if there is no PCIe device present.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The SPD detection code for the Denali memory controller used on some
ppc4xx
processors incorrectly encodes DDR0_42. With certain memory
configurations,
this can cause the bootwrapper to incorrectly calculate the installed
memory
size, because the number of row bits is wrong. This patch fixes that
encoding.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As discussed on mailing list, <0 indicates failure, >=0 indicates number
of interfaces found.
Also added blurb about private data
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
if link up detection code is disabled through config option, it gives build warning.
This patch fixes the same
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
following build warning was observed
mv88e61xx.c: In function ‘mv88e61xx_busychk’:
mv88e61xx.c:208: warning: dereferencing type-punned pointer will break strict-aliasing rules
This patch fixes the same
Patch tested for rd6281a board build
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
On 405EZ the RX-/TX-interrupts are coalesced into one IRQ bit in the
UIC. We need to acknowledge the RX-/TX-interrupts in the
SDR0_ICINTSTAT reg as well.
This problem was introduced with commit
d1631fe1 [ppc4xx: Consolidate PPC4xx UIC defines]
Signed-off-by: James Clough <james@rtetc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The random_port() is meant to be used by other net code, but without a
prototype, we get fun warnings like:
dns.c: In function 'DnsSend':
dns.c:89: warning: implicit declaration of function 'random_port'
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
FLAG_PARSE_SEMICOLON is not defined without hush.h, so include that.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Refactor the smc911x driver to allow for detecting when the chip is missing.
I.e. the detect_chip() function is called earlier and will abort gracefully
when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Some DaVinci SOC's use GPIOs to enable EMAC and DM9000.
This patch adds some definitions for GPIO registers and also adds
structures for GPIO.
A separate header file is being added so that in future we
can have a DaVinci GPIO driver similer to OMAP.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
In the DaVinci specific code, we use both CONFIG_SOC_DM646X and
CONFIG_SOC_DM646x to represent DM646x specific code.
This patch changes occurrences of CONFIG_SOC_DM646x to
CONFIG_SOC_DM646X. This is because for DM644x series of SOCs we use
the flag CONFIG_SOC_DM644X. We want some uniformity.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on mv88f6281gtw_ge board.
To create Kirkwood boot image to be flashed on SPI Flash,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds kwbimage configuration file
(used by mkimage utility)
to support u-boot.kwb target on rd6281a platform.
To create Kirkwood boot image to be flashed on NAND,
additional parameter u-boot.kwb need to be passed during make.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
Signed-off-by: Heiko Schocher <hs@denx.de>
- As these boards are similiar, collect common config options
in manroland/common.h and manroland/mpc52xx-common.h
for mpc5200 specific common options for this manufacturer.
- add OF support
- update default environment
Signed-off-by: Heiko Schocher <hs@denx.de>
Minor edit of commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 002741ae86 modified include/asm-ppc/mmu.h such that the LAWAR_
defines were only enabled for the 83xx platform, but they are also
needed on MPC512x system. Enabling these for E300 systems seems thus
more appropriate.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Martha M Stan <mmarx@silicontkx.com>
Minor cleanup:
Re-ordered default_mddrc_config[] to have matching indices.
This allows to use the same index "N" for source and target fields;
before, we had code like this
out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]);
which always looked like a copy & paste error because 2 != 3.
Also, use NULL when meaning a null pointer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The means to determine the core, bus, and DDR frequencies are completely
new on CoreNet style platforms. Additionally on p4080 we can have
different frequencies for FMAN and PME IP blocks. We need to keep track
of the FMAN & PME frequencies since they are used for time stamping
capabilities inside each block.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet style platforms the timebase frequency is the bus frequency
defined by 16 (on PQ3 it is divide by 8). Also on the CoreNet platforms
the core not longer controls the enabling of the timebase. We now need
to enable the boot core's timebase via CCSR register writes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p4080 & p4040 to cpu_type_list and SVR list
* Added number of LAWs for p4080
* Set CONFIG_MAX_CPUS to 8 for p4080
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CoreNet platform style of bringing secondary cores out of reset is
a bit different that the PQ3 style. Mostly the registers that we use
to setup boot translation, enable time bases, and boot release the cores
have moved around.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet based platforms the CCSRBAR address is split between an high &
low register and we no longer shift the address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On CoreNet based platforms the LAW address is split between an high &
low register and we no longer shift the address. Also, the target IDs
on CoreNet platforms have been completely re-assigned.
Additionally, added a new find_law() API to which LAW an address hits in.
This is need for the CoreNet style boot release code since it will need
to determine what the target ID should be set to for boot window
translation.
Finally, enamed LAWAR_EN to LAW_EN and moved to header so we can use
it elsewhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p4080 SoC has a significant amount of commonality with the 85xx/PQ3
platform. We reuse the 85xx immap and just add new definitions for
local access and global utils. The global utils is now broken into
global utils, clocking and run control/power management.
The offsets from CCSR for a number of blocks have also changed. We
introduce the CONFIG_FSL_CORENET define to distinquish the PQ3 style of
platform from the new p4080 platform. We don't use QoirQ as there are
products (like p2020) that are PQ3 based platforms but have the QoirQ
name.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code assumed names where just numbers and always prefixed 'mpc'.
However newer QorIQ don't follow the mpc naming scheme.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When boot from NAND, the NAND flash must be connected to br/or0.
Also init RAM(L2 SRAM or DDR SDRAM) for load the second image to
it.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The first stage 4K image uses a seperate ld script file to
generate 4K image. This patch moves it to the cpu/mpc85xx/*
to make it avaliable for 85xx platform.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
