The USB port 0 can now be used alongside the USB port 1, thus enable
power to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board
may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo
(MX6DL) by including the proper header.
Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd
only support MX6Q, so they include mx6q_pins.h.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Rather than load the FPGA file from the FAT partition, look
at entry in system EEPROM to decide which file to retrieve directly
from the EXT3 partition.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
The pcm051 does not have the wp pin connected to the sd-card socket.
Therefore remove the pinmux for the pin. The was a carry-over from
the am335x evm code.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay
for RGMII mode not supported). This in turn however requires that we
set the tx clock delay feature in the PHY itself.
Signed-off-by: Tom Rini <trini@ti.com>
All the users of mx6q_4x_mt41j128.cfg (DDR3-1333H Micron MT41J128M16HA-15E or SK
hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and DDR3-1600K Micron
MT41K128M16JT-125:K for i.MX6 SABRE SD) support the optional down binning to
DDR3-1066F (CL = 7, CWL = 6), which is possible at 532 MHz, so use it.
In these conditions:
tRCD(min) = 13.125 ns
tRP(min) = 13.125 ns
tRC(min) = max(tRAS(min, DDR3-1333H), tRAS(min, DDR3-1600K)) + tRP(min)
tRAS(min, DDR3-1333H) = 36 ns
tRAS(min, DDR3-1600K) = 35 ns
MMDC1_MDCFG0.tCL should be set to 7 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG0[3:0].
MR0.CL should be set as in MMDC1_MDCFG0.tCL, i.e. to 7 nCK, which is encoded
as 0x6 in MRS.LMR.MR0.{A6:A4, A2} and MMDC1_MDSCR[22:20, 18].
MMDC1_MDCFG1.tCWL should be set to 6 nCK, encoded as 0x4 in the bit-field
MMDC1_MDCFG1[2:0].
MMDC1_MDCFG1.tRCD should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[31:29].
MMDC1_MDCFG1.tRP should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded
as 0x6 in the bit-field MMDC1_MDCFG1[28:26].
MMDC1_MDCFG1.tRC should be set to 49.125 ns, which is 27 nCK at 532 MHz, encoded
as 0x1A in the bit-field MMDC1_MDCFG1[25:21].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MR0.PPD should be set as in MMDCx_MDPDC.SLOW_PD, i.e. to fast-exit mode, which
is encoded as 1 in MRS.LMR.MR0.A12 and MMDCx_MDSCR[28].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.RST_to_CKE should be set to 500 µs according to the JEDEC
specification for DDR3. With a cycle of 15.258 µs, this gives 33 cycles encoded
as 0x23 for the bit-field MMDC1_MDOR[5:0].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.SDE_to_RST should be set to 200 µs according to the JEDEC
specification for DDR3. With a cycle of 15.258 µs, this gives 14 cycles encoded
as 0x10 for the bit-field MMDC1_MDOR[13:8].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDOR.tXPR should be set as specified for the JEDEC DDR3 timing tXPR.
For all DDR3 speed bins:
tXPR(min) = max(5 nCK, tRFC(min) + 10 ns)
tRFC(2 Gb) = 160 ns
All the users of mx6q_4x_mt41j128.cfg have a 2-Gb density (Micron
MT41J128M16HA-15E or SK hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and Micron
MT41K128M16JT-125:K for i.MX6 SABRE SD).
Hence, MMDC1_MDOR.tXPR should be set to max(5 nCK, 170 ns), which is 170 ns
and 91 nCK at 532 MHz, encoded as 0x5A in the bit-field MMDC1_MDOR[23:16].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
MMDC1_MDCFG1.tMRD should be set to max(tMRD, tMOD) for DDR3.
For all DDR3 speed bins:
tMRD(min) = 4 nCK
tMOD(min) = max(12 nCK, 15 ns)
Hence, MMDC1_MDCFG1.tMRD should be set to max(12 nCK, 15 ns), which is 12 nCK
at 532 MHz, encoded as 0xB in the bit-field MMDC1_MDCFG1[8:5].
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add driver for tegra SPI "SLINK" style driver. This controller is
similar to the tegra20 SPI "SFLASH" controller. The difference is
that the SLINK controller is a genernal purpose SPI controller and the
SFLASH controller is special purpose and can only talk to FLASH
devices. In addition there are potentially many instances of an SLINK
controller on tegra and only a single instance of SFLASH. Tegra20 is
currently ths only version of tegra that instantiates an SFLASH
controller.
This driver supports basic PIO mode of operation and is configurable
(CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4
devices per controller may be attached, although typically only a
single chip select line is exposed from tegra per controller so in
reality this is usually limited to 1.
To enable this driver, use CONFIG_TEGRA_SLINK
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add tegra30 SPI SLINK nodes to fdt.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add back host1x node to seaboard dts file. This got dropped during
the tegra fdt sort.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The libfdt.h file is the definition file for libfdt. It is unnecessary
to include other fdt header files (the necessary ones are pulled in
by libfdt.h).
Signed-off-by: Gerald Van Baren <gvb@unssw.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
This mux is not currently used and appears to be a carry-over from the
am335x evm code.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
commit b689cd5 OMAP3: use a single board file for IGEP devices
introduced the following build warning:
igep00x0.h:168:24: warning: backslash-newline at end of file [enabled
by default]
This patch fixes the issue.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.
[Hebbar Gururaja <gururaja.hebbar@ti.com>]
- Resolve merge conflict while rebasing. File structure is
changed in the mainline. So re-arrange the code accordingly.
- Update commit message to reflect the DDR3 part number
Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
When ethaddr is not set in environment the MAC address is read
from efuse. The message was only printed in debug case, but this
message could be of interest for the ordinary user, so printf it.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD
Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI
Not yet supported:
NAND
RTC
LCD
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds an GPIO LED boot status for IGEP boards.
The GPIO LED used is the red LED0 while the Linux kernel
uses the green LED0 as the boot status.
By using different GPIO LEDs, the user can know in which
step of the boot process the board currently is.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.
So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.
This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update for bsc9132qds.c, b4860qds.c]
Signed-off-by: Tom Rini <trini@ti.com>
This code was targetting one specific Microblaze platform
configuration which is obsolete and fsl bus isn't used
in this way.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these files was used for ancient xilinx drivers
which are finally gone.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
There is new driver in the driver folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Older compilers don't recognize v7 wfi instruction, so use wfi macro to
fix builds on old compilers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
