The copy buffer, if enabled, prevents booting from coreboot correctly,
since no memory is allocated for it. Allow it to fall back to disabled
in this situation. This ensures that a console is displayed, even if
it is slow.
Signed-off-by: Simon Glass <sjg@chromium.org>
As on some incipient Layerscape platforms (LS1043A series) there isn't
separate PF control register block, these registers reside in the LUT
register block, so when the driver detected there isn't 'ctrl', it will
assign the 'lut' address to the ls_pcie->ctrl.
The current code allocate memory for the struct ls_pcie with random
contents, this can result in skipping to assign the ls_pcie->ctrl with
the 'lut' address, then further crash with the incorrect address.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Marvell Armada 3720 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in U-Boot PCIe controller driver aardvark for
both PCI vendor id and PCI subsystem vendor id.
This change affects PCI vendor id of PCIe root bridge emulated by Linux
kernel. With this change Linux kernel reports correct vendor id 11AB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the driver only supports 32-bit bus and cpu address.
The controller's outbound registers/fields for extended address
are not programmed. Let's program them to support 64-bit bus and
cpu address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
devfdt_get_addr_index() returns fdt_addr_t which might be a 64-bit
physical address. Use map_physmem() to return the virtual address
that can be used by a 32-bit machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For the QEMU ppce500 machine, LAW registers are not implemented
hence CONFIG_FSL_LAW is not turned on and all LAW APIs are not
available. We should wrap all LAW registers programming in the
mpc85xx PCI driver with CONFIG_FSL_LAW.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
changes 'struct pci_controller'.regions from pre-allocated array of
regions to dynamically allocated, which unfortunately broken lots of
boards that still use the non-DM PCI driver.
This patch changes the non-DM fsl_pci_init driver to dynamically
allocate the regions, just like what's done in the pci uclass driver.
Fixes: e002474158 ("pci: pci-uclass: Dynamically allocate the PCI regions")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the map address and mask must be power of two per documentation,
adjust the code accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to access the PCIe root bus space and configure it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Rockchip dwc based PCIe controller driver for rk356x platform.
Driver support Gen3 by operating as a Root complex.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add a return value to pci_init and use it directly in the post-relocation
init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.
Also move the functions into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Now that the sequence-numbering migration is complete, rename this member
back to seq_, adding an underscore to indicate it is internal to driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This reverts commit 828d326216.
This change revers code which asserting PERST# signal when unloading
driver. Driver's remove callback is still there as it is used for other
functionality.
Asserting PERST# signal prior booting kernel is causing that A3720 boards
(Turris MOX and Espressobin) with stable Linux kernel versions 4.14 and
4.19 are not able to detect some PCIe cards (e.g. Compex WLE200 and WLE900)
and anymore. When PERST# signal is not asserted these cards are detected
correctly. As this is regression for existing stable Linux kernel versions
revert this problematic change in U-Boot.
To make cards working with OpenWRT 4.14 kernel it is needed to disable link
training prior booting kernel, which is already done in driver's remove
callback.
Described issue is in Linux kernel pci aardvark driver which is (hopefully)
fixed in latest upstream versions. Latest upstream versions should be able
to initialize PCIe bus and detects cards independently of the link training
and PERST# signal state.
So with this change, U-Boot on A3720 boards should be able to boot OpenWRT
4.14 kernel, stable 4.14 and 4.19 kernels and also latest mainline kernels.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This function current deals with req_seq which is deprecated. Update it to
use the new sequence numbers, putting them above existing aliases. Rename
the function to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we know the sequence number at bind time, there is no need for
special-case code in dm_pci_hose_probe_bus().
Note: the PCI_CAP_ID_EA code may need a look, but there are no test
failures so I have left it as is.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix up the code style for those declarations that should now fit onto one
line, which is all of them that currently do not.
This is needed for dtoc to detect the structs correctly, at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: commit 8ec619f8fd ("pci: layerscape: Fixup PCIe EP
mode DT nodes for LX2160A rev2")
This added the PCIe EP nodes fixup of LX2160A, but it
didn't update the condition value when there isn't a
property 'apio-wins'.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Fixed checkpatch error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
