Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Enable setexpr command in defconfig for Turris MOX. We have found that
this is sometimes useful in U-Boot scripts and there is enough space in
NOR memory on MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable wdt command in defconfig for Turris MOX. This is useful when
doing debugging.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To check if some output characters are waiting either in Transmitter
Holding Register or Transmitter Shift Register we need to look at
TX_EMPTY bit of UART Status Register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the documentation build system according to Linux v5.11-rc1.
Deactive the automarkup.py extension module which on Gitlab CI is
incompatible with Unicode.
With this patch we can build the HTML documentation using either of
Sphinx 2 and Sphinx 3.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Install all requirements according to doc/sphinx/requirements.txt in the
virtual environment used for testing 'make htmldocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sphinx 3 builds fail due to doc/develop/logging.rst producing duplicate
labels.
Include logging.h only once in the API section and use cross-references for
the enums log_level_t and log_category_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A few minor changes:
* Get rid of leftover comments, other commits removed the defines they
referred to.
* CONFIG_SYS_NETA_INTERFACE_TYPE is not used anymore since commit
e3b9c98a23 ("net: mvneta: Convert to driver model").
* Drop CONFIG_USB_MAX_CONTROLLER_COUNT: it is per-HCI type, so XHCI and
EHCI could still both work be used.
* Unconditionally define CONFIG_EHCI_IS_TDI: it has no effect on XHCI so
that conditional doesn't make any sense.
* Define a larger PHY_ANEG_TIMEOUT: In my test bed, the NIC is directly
connected to some RTL8111 and the default 8s timeout was often too
short.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SATA and UART ClearFog imaages are not buildable as ENV_SECT_SIZE is not defined
set values for both possible targets
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Move all aliases defintions into the main dts file
Add u-boot definiton to i2c0 based on clearfog
set spi1 status to okay
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Stefan Roese <sr@denx.de>,
Reviewed-by: Stefan Roese <sr@denx.de>
When testing builds provided in https://github.com/openwrt/openwrt/pull/3360
I discovered that fdtfile was not set and as a result the firmware was not
functional. So I am documenting what is needed.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Karsten Merker <merker@debian.org>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 pinctrl is no different configuration wise than others, so just add
compatible for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 uses different address for reset. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There was no need to have prcm definitions for H6 and similar SoCs till
now. However, support R_I2C will be needed soon in SPL.
Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h.
One of those files will be selected in common prcm.h based on defined
macros.
This commit doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Updated H6 DT files are based on Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
-----BEGIN PGP SIGNATURE-----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=0CgJ
-----END PGP SIGNATURE-----
Merge tag 'doc-2021-04-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for documentation tag doc-2021-04-rc1 (2)
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
