This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move a few mux defines around so that all the mux defines are properly sorted
by port number.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.
This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
With driver model we will have access to a bank pointer, so we want to
use it rather than converting back to a number, and then back to a
bank pointer. Add functions to provide this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.
Add support for R_UART so we can have a console while using mmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31, A23 and later SoCs have an extra pin controller, called CPUs_PIO
or R_PIO, which handles pin banks L and beyond.
Also add a clear description about SUNXI_GPIO_BANKS, stating it only
counts the number of pin banks in the _main_ pin controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: expanded commit message]
[wens@csie.org: add pin bank M and expand comments]
[wens@csie.org: add comment on SUNXI_GPIO_BANKS macro]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
None of the known sunxi devices actually use mmc1 routed through PH, where
as some devices do actually use mmc1 routed through PG, so change the routing
of mmc1 to PG. If in the future we encounter devices with mmc1 routed through
PH, we will need to change things to be a bit more flexible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
