This is not used since this commit:
3cf02f5ffa imx6: remove not longer supported aristainetos boards
Drop the driver and Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
The KONA and KONA_GPIO options don't exist anymore, since this commit:
0f6807e77b arm: Remove bcm28155_ap board
Drop the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes the Makefile rules or source code refers to Kconfig options
which don't exist. Update the moveconfig tool to check this and produce
a series of reports about inconsistencies.
This can then be used to generate patches to correct the problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Default to dynamic LMB allocation, and fix an issue with the EFI one,
assorted TI platform updates, socrates platform updates, switch
qemu-arm to using bootstd, imagetool fixes, macOS host build fixes,
keymile platform upates, spl FPGA load fix, MMC env bugfix, add seama
command, usb bootdev test bugfix.
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the issue in commit 46c9016 ("env: mcc: Drop unnecessary #ifdefs")
If CONFIG_SYS_REDUNDAND_ENVIRONMENT is not defined, the offset value
becomes undetermined, so write env to unexpected offset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If image file is stored on flash partition then it contains padding, which
is not part of the image itself. Image data size is stored in the image
header. So use image size from the header instead of expecting that total
image file size is size of the header plus size of the image data. This
allows dumpimage to parse image files with padding (e.g. dumped from flash
partition).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before reading image header, verify that image size is at least size of
the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpimage type requires only that two first 32-bit words of data file are
non-zero. So basically every random data file can be guessed and verified
as gpimage. So completely skip gpimage type from image autodetection code
to prevent lot of false positive results. Data file with gpimage type can
be still verified and parsed by explicitly specifying -T gpimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
This supports reading a kernel and ramdisk from qfw, then loading it with
either the booti or bootz commands.
For now this uses the existing booti and bootz commands, rather than
trying to call that functionality directly (e.g. do_bootm_states()). It
does not require the HUSH parser though, which helps a little with size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev device for qfw so that it can be used with standard boot.
This simply checks for the correct method and then does the read. Most of
the other logic is handed in a new bootmeth driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is currently in the cmd/ file but we want to call it from a driver.
Move it into a common place. Tidy up the header-file order while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses casts all over the place. Use the correct type so that these
can be avoided, as is done with other commands. Also simplify a few
conditionals.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present virtio tries to attach QEMU services to a bootdev device, which
cannot work. Add a check for this.
Also use bootdev_setup_sibling_blk() to create the bootdev device, since
it allows the correct name to be used and bootdev_get_sibling_blk() to
work as expected.
The bootdev is not created on sandbox since it does have a real virtio
device and it is not possible to read blocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a60f7a3e35 ("bootstd: Add a virtio bootdev")
Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In some cases the block device is obtained but is not probed, since it
is a sibling of the bootdev. Make sure it is probed, so it can be used
without any trouble.
This fixes a bug with virtio, where the device is accessed before it has
been set up by the virtio uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 201417d700 ("bootstd: Add the bootdev uclass")
Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is sometimes useful to have one without the other, e.g. on a device
without a display, since at present the expo feature requires CONFIG_VIDEO
to be enabled.
Update the Makefile and bootflow command to support this, as well as the
EXPO dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
