Rather than keeping the asynchronous schedule running always, keep it
running only across USB mass storage transfers for now, as it seems
that keeping it running all the time interferes with certain control
transfers during device enumeration.
Note that running the async schedule all the time should not be an
issue, especially on EHCI HCD, as that one implements most of the
transfers using async schedule.
Note that we have usb_disable_asynch(), which however is utterly broken.
The usb_disable_asynch() blocks the USB core from doing async transfers
by setting a global flag. The async schedule should however be disabled
per USB controller. Moreover, setting a global flag does not prevent the
controller from using the async schedule, which e.g. the EHCI HCD does.
This patch implements additional callback to the controller, which
permits it to lock the async schedule and keep it running across
multiple transfers. Once the schedule is unlocked, it must also be
disabled. This thus prevents the async schedule from running outside
of the USB mass storage transfers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com> [omap3_beagle, previously failing]
Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.
Move those options to be set for all Allwinner boards in their
respective Kconfig files.
The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
accesses, we don't care about filesystems or partitions in there, so
there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
specifying this reduces the latency of the USB keyboard handling, so
this was formerly enabled in config headers for all Allwinner boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
After the commit 9b643e312d ("treewide: replace with error()
with pr_err()"), there are pr_err() usages without line break. Add
missing line breaks for pr_err() used in f_thor.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
In case dfu command is being executed with timeout option,
the timer may expire in the middle of DFU operation. If there
is DFU request coming, we may simple reset timeout value
to prevent aborting of ongoing DFU operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEUdvKHhzqrUYPB/u8L21+TfbCqH4FAl43/6QSHG1icnVnZ2Vy
QHN1c2UuY29tAAoJEC9tfk32wqh+Fq0P/1vCbkiRgOtOIMPh/b7qWUVweTdgwcbf
9v8Qa2IKc0FYgjYjIMjihfbvF7R0vGaOUX13yKDV/3v42cpLkOxBauCYasiXznI+
9hBwKfOFPzLpSz3SJ+LRn0XhHSAZ1jcT19pgaPmA5Pry6l7JEai4M3JFeYeJRWOt
N1EFqxqqeAQ+eXdQWXTKh6AiFEia7aL4OVcU5HY9BMyDW8H13gvNejoeSXNKLupM
GGHJfG/TRKHP5UJoqH+I9XFdkUKfN4e1oWpxl7nA5HpvRfFgO+AQm9OgM2xumnGp
+4kS4T5FexCrcQ37m5fG9+LSxk2PB8+P0kmfImaO54lUdAtjB+iqg4RUB7eN/vLH
37S13AB7T8OTjbe8tlLCjGDXQ/8xU+NDZQsE9GnRmaj2UbK57hJPW6kTRgwK4BEZ
l0Rr9RrHlhrBvywHMII11fhH+wVO0R29GFvRZSSscRqvKq61FF//r8hNQX7xtErf
+OIEgIcEt9bbLyq7LJQ+2xRdQj4UgSv5/poaaoWX+uY4+yUElbiPpTJLN2oslZ8x
liUKigWmTgF8G1ukalyA1u3xj0kyfl4QCxoJpNqoaHg9sel0S5igGE0dLzKXUKSw
1A7BCT0rO/FhoMxc7P4kHjpIKlw6Tatw1wJY3g8VzRgEsXlTawNszadO1jswBmHV
9XFk+iH6f/rg
=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Invalidate dcache line before accessing Setup Packet contents. Otherwise
driver will see stale content on non coherent architecture.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Broadcom 2835 SoC requires special conversion of physical memory addresses
for DMA purpose, so add needed wrappers to dwc2_udc_otg driver. Also extend
the list of compatible devices with 'brcm,bcm2835-usb' entry. This allows
to use USB gadget drivers (i.e. DFU) on Raspberry Pi4 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
AM654 has DWC3 USB controller that is very similar to other TI SoCs. Add
a new compatible to enable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Signed-off-by: Simon Glass <sjg@chromium.org>
These macros use __FILE__ which inserts the full path of the object file
into U-Boot, thus increasing file size. Drop these usages.
An older version of this patch was submitted here:
http://patchwork.ozlabs.org/patch/1205784/
Signed-off-by: Simon Glass <sjg@chromium.org>
DWC3 support phy interfaces like 8/16-bit UTMI+. phy interface
initialization code would handle them properly along with UNKNOWN
type by default if none of the user/board doesn't need to use the
phy interfaces at all.
The current code is masking the 8/16-bit UTMI+ interface bits globally
which indeed effect the UNKNOWN cases, therefore it effects the platforms
which are not using phy interfaces at all.
So, handle the phy masking bits accordingly on respective interface
type cases.
Fixes: 6b7ebff001 ("usb: dwc3: Add phy interface for dwc3_uboot")
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since, commit 62f9b65447 ("common: Move older CPU functions to their own header")
cache ops functions are declared in a separate header. Include the same
to avoid build warnings.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function header to serial.h since this function is clearly
related to serial. The function itself stays in console.c since we don't
have a single serial file. DM and non-DM each has a separate file so we
would have to either create a new common serial file, or repeat the
function in both serial.c and serial-uclass.c, neither of which seem
worthwhile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Allow the unit test to pass full 8 byte scan code sequences to the USB
keyboard emulation driver and to parse multi-byte escape sequences.
The following features are not yet tested:
* LED status
* caps-lock
* num-lock
* numerical pad keys
The following features are not yet implemented by the USB keyboard
driver and therefore not tested:
* modifiers for non-alpha-numeric keys, e.g. <SHIFT><TAB> and <ALT><F4>
* some special keys, e.g. <PRINT>
* some modifiers, e.g. <ALT> and <META>
* alternative keyboard layouts
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide support for F1-F12, Insert, Delete, Home, End, Page Up, Page Down.
As this leads to a size increase provide a customizing setting
CONFIG_USB_KEYBOARD_FN_KEYS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
Add 0x330c for rk3399 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot has two different variants of dwc3 initializations,
- with dm variant gadget, so the respective dm driver would
call the dwc3_init in core.
- with non-dm variant gadget, so the usage board file would
call dwc3_uboot_init in core.
The driver probe would handle all respective gadget properties
including phy interface via phy_type property and then trigger
dwc3_init for dm-variant gadgets.
So, to support the phy interface for non-dm variant gadgets,
the better option is dwc3_uboot_init since there is no
dedicated controller for non-dm variant gadgets.
This patch support for adding phy interface like 8/16-bit UTMI+
code for dwc3_uboot.
This change used Linux phy.h enum list, to make proper code
compatibility.
Cc: Marek Vasut <marex@denx.de>
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add 0x310c for rk3128 gadget product number.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip support differnet or common gadget product number
between Rockchip SoCs like,
0x310a - rk3036
0x320a - rk3229, rk3288
0x330a - rk3328
So, select them on Kconfig based on platform specific
config defined.
This eventually drop the explicit configs defined in
supporting board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.
So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.
This eventually drop the explicit defined added
on supported board defconfig files.
Tested-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting dwc2_fifo_read to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since upgrading to gcc9, warnings are issued:
"taking address of packed member of ‘...’ may result in an unaligned
pointer value"
Fix this by converting two functions to use unaligned access since packed
structures may be on an unaligned address, depending on USB hardware.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
xhci.h has now been moved to include/usb/ directory. Therefore, update the
path in the Cadence USB drivers.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The xHCI 1.1 version also need set Transfer Type field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To add usb-3.0 support to peripheral device add BOS & SS capability
descriptors to gadget composite framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Add a new bcdDevice entry for Cadence USB gadget controller similar to
other controller and add gadget_is_cdns3() macro as well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add driver to handle TI specific wrapper for Cadence USB3 controller
present on J721e SoC. Based on Linux driver for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Implement udc_set_speed() callback to limit Controller's speed to
high-speed/full-speed when working with gadgets that are high-speed or
full-speed only
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for USB3 host and gadget driver. This is a direct sync of
Linux kernel Cadence USB stack that from v5.4-rc1 release.
Driver has been modified so that it compiles without errors against
U-Boot code base.
Features not required for U-Boot such as scatter-gather DMA and OTG
interrupt handling has been dropped.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[jjhiblot@ti.com: Add PHY support]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This patch was copied from kernel commit: 67fdfda4a99ed.
Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver because that will just fail.
So here introduce a new optional ->udc_set_speed() method which can be
implemented by interested UDC drivers to achieve this purpose.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add match_ep() op to usb_gadget_ops similar to Linux kernel which is
useful in finding a suitable ep match for the function driver. This will
avoid adding more gadget_is_xxx() handling code to usb_ep_autoconfig().
Also sync usb_ep_caps struct thats is usually used in the match_ep()
callback by the gadget controller driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Profiling the EHCI driver shows a significant performance problem in
ehci_submit_async(). Specifically, this function keeps enabling and
disabling async schedule back and forth for every single transaction.
However, enabling/disabling the async schedule does not take effect
immediatelly, but instead may take up to 1 mS (8 uFrames) to complete.
This impacts USB storage significantly, esp. since the recent reduction
of maximum transfer size to support more USB storage devices. This in
turn results in sharp increase in the number of ehci_submit_async()
calls. Since one USB storage BBB transfer does three such calls and
the maximum transfer size is 120 kiB, the overhead is 6 mS per 120 kiB,
which is unacceptable.
However, this overhead can be removed simply by keeping the async
schedule running. Specifically, the first transfer starts the async
schedule and then each and every subsequent transfer only adds a new
QH into that schedule, waits until the QH is completed and does NOT
disable the async schedule. The async schedule is stopped only by
shutting down the controller, which must happen before moving out
of U-Boot, otherwise the controller will corrupt memory.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Calling cache flush on invalid buffer, even with zero length might cause
an exception on certain platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This is needed to make Windows THOR flash tool happy, because it
starts sending data only when interrupt packet is received on the 3rd
endpoint.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some boards don't populate clk/reset entries as these are are optional
as per binding documentation. Therefore, don't fail driver probe if
clk/reset entries are absent in DT.
This fixes fastboot failures seen due to enabling of CONFIG_CLK on AM57xx
Fixes: e8e683d33b ("board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Example of USB nodes for iMX7S/D:
usbotg1: usb@30b10000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b10000 0x200>;
^^^^^^^^^^
....
usbotg2: usb@30b20000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b20000 0x200>;
^^^^^^^^^^
....
usbh: usb@30b30000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b30000 0x200>;
^^^^^^^^^^
....
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.
Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function that read quirk and configuration information from the
DT. The goal is to allow platforms using their own version of DWC3 driver
to migrate to the generic DWC3 driver.
The function is adapted from the function dwc3_get_properties() in the
linux dwc3 driver introduced in commit c5ac6116db35d.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no need to fail if the maximum speed is not specified.
If the speed is not specified, do the same as linux and assume super speed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Currently the host driver used by dwc3-generic is "xhci-dwc3". This is
a functional driver but it doesn't use the dwc3 core and, in particular,
it lacks some bits that may be important.
For example on the k2 platforms, it is important that the phy are properly
suspended when the USB is not used anymore. The dwc3 core also has a
partial support for quirks.
The new driver can be used as a drop-in replacement for "xhci-dwc3".
In terms of implementation, it may seem strange that 2 private structures
dwc3_generic_host_priv and dwc3_generic_priv) are used. The reason for this
is simply that the xhci layer expects a struct xhci_ctrl at the beginning
of the private data and it seemed wasteful to include it also for the
peripheral case.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No one is actually implementing those functions.
We could remove calls to these altogether, but it does not really hurt to
keep the empty inlined version at the moment and it satisfies a symmetry
with the gadget mode.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allow the phy to enter idle and then suspend.
the K2 platforms require the PHY to be suspended before the USB domain
clock can be turned off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Phy setup should be done before dwc3 soft core reset as it is done
in linux & this fixes unreliable detection of usb cable on host side.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
commit 65c1f9820c8f79f "usb: Add nonblock argument to submit_int_msg"
breaks the musb_hcd driver.
Fixing it by adding the missing argument
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
An USB 1.1 keyboard connected to dwc2 through a high-speed hub does not
report status until it changes. With this patch you can enable keyboard
by pressing a key while USB devices are probed. Without a keypress no
state is reported and the probe times out. We don't want to wait for a
keypress or timeout while polling for keypresses so implement an int_msg
nonblock variant that exits early on error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
This quirk is necessary for the Amlogic GXL SoCs otherwise the
Port 2 PHY doesn't get out of suspend and U-Boot resets the board after:
XHCI timeout on event type 33... cannot recover.
BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
This quirk is also handled in the dwc3 core code, but until the
xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here
to fix USB support on the Amlogic libretech-cc and libretech-ac board
when a device is only plugged in the OTG port.
Cc: Yuri Frolov <crashing.kernel@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add DM regulator support for toggling VBUS, this is useful on boards
which control the VBUS e.g. through GPIO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Fix remaining checkpatch complaints in the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Add missing Kconfig entry for the R8A66597 driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Convert the R8A66597 USB driver to DM and add support for DT probing.
Drop support for legacy non-DM and non-DT probing, since there are no
platform using that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Replace R8A66597_BASE0 with proper SYSCFG0 accesses, no functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
While the USB controller can work both in LE and BE modes, there is
no user for the BE mode, so drop it. If there ever is a user for it,
it can be easily re-added back.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Replace in{bwl}()/out{bwl}() IO accessors with read{bwl}()/write{bwl}(),
to make the driver compile both on SH and ARM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
No other platforms use this r8a66597 controller but RZ/A1,
make RZ/A1 support the default and drop all the other SoC
support to remove ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Remove CONFIG_SUPERH_ON_CHIP_R8A66597 macro, which is unused.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
dfu_prepare_function() allocates N+1 descriptor header structures,
the last one being the "DFU Functional Descriptor".
dfu_unbind() handles de-allocation, but fails to free the final
one (eg. "DFU Functional Descriptor"), leading to memory leak.
Fixed by incrementing counter, as in dfu_prepare_function().
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
commit 57faca19a8 ("drivers: USB: OHCI: allow compilation for 64-bit targets")
broke ohci support for the mpc85xx based socrates board,
as it removed volatile keyword from ohci_readl/writel.
Fix this so usb works again on socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
var ohci_pci_ids is only used if DM_USB is not enabled.
So define this varaible only if
!CONFIG_IS_ENABLED(DM_USB)
Signed-off-by: Heiko Schocher <hs@denx.de>
With the recently added phy driver, this patch will enable the
musb driver on the da8xx to operate in host mode.
Signed-off-by: Adam Ford <aford173@gmail.com>
Remove RK3399 compatible strings as this driver is no longer
used on that SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure USB2 PHY register based on "phy_type" property and
handle all the quirks that are relevant for Rockchip RK3399 SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add compatible string for RK3399 and enable it by default on
Rockchip platforms with USB3 support.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
[...]
CC drivers/usb/gadget/f_mass_storage.o
CC drivers/usb/musb-new/omap2430.o
CC drivers/usb/gadget/f_fastboot.o
CC env/common.o
CC env/env.o
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
/src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
ret = musb_register(&platdata->plat,
^
LD drivers/usb/host/built-in.o
CC drivers/usb/gadget/f_sdp.o
CC fs/ext4/ext4fs.o
[...]
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[Various build fixes]
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
Allow device mode in DWC2 driver when device tree select the dr_mode
"peripheral" or "otg".
The device mode is not allowed when dr_mode = "host" in device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Manage g-tx-fifo-size as a array as specify in the binding.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
So adopt 32 bit address for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch reuses some former code for the hawkboard, combines it
with some some similar DM_USB compatible code for the OHCI driver,
and enables the use of the da850's OHCI controller with DM_USB
compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
The support for DaVinci DM* SoCs has been dropped. The ifdefs in the
musb_hcd driver are no longer needed. Remove them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Marek Vasut <marex@denx.de>
There is a delay function that was commented out. This patch
re-enables it, because it will be needed for da850 ohci support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This fixes a disconnect issue detected with fastboot command, when using
dwc2 driver.
- On u-boot side:
uboot>$ fastboot 0
- On USB host PC side, few seconds after
PC>$ fastboot reboot # Get stuck, uboot target never reboots
By enabling DEBUG_ISR logs, the bus suspend interrupt is seen before the
PC command has been issued. When the USB bus suspend occurs, there's a HACK
that disables the fastboot (composite driver). Here is the call stack
upon USB bus suspend:
- dwc2_handle_usb_suspend_intr()
- dev->driver->disconnect()
- composite_disconnect()
- reset_config()
- f->disable()
- fastboot_disable()
- usb_ep_disable(f_fb->out_ep);
- usb_ep_disable(f_fb->in_ep);
.. other disable calls.
When the resume interrupt happens, everything has been disabled, then
nothing happens. fastboot command gets stuck on HOST side.
Remove original HACK, that disconnects the composite driver upon
USB bus suspend. Implement disconnect detection instead:
- check GINTSTS OTG interrupt
- read GOTGINT register
- check GOTGINT, SesEndDet bit (e.g. session end)
This is inspired by what is implemented currently in Linux dwc2 driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add compatible "st,stm32mp1-hsotg" and associated driver data to manage
the usb33d-supply and the ST specific register for VBus sensing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c
Reviewed-by: Lukasz Majewski <lukma@denx.de>
All TX fifo size can be different, add tx_fifo_sz_array[]
into dwc2_plat_otg_data to be able to set them.
tx_fifo_sz_array[] is 17 Bytes long and can contains max 16
tx fifo size (synopsys IP supports max 16 IN endpoints).
First entry of tx_fifo_sz_array[] is the number of valid
fifo size the array contains.
In case of tx_fifo_sz_array[] doesn't contains the same
number of element than max hardware endpoint, display
a warning message.
Compatibility with board which doesn't use tx_fifo_sz_array[]
(Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Some DWC2 ip variant doesn't use 16 hardware endpoint as hardcoded
in the driver. Bits INEps [29:26] of HWCFG4 register allows to get
this information.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add a new function to check the session B validity, to be use to check
cable connection.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reset the hardware to be sure of the device state.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Minimal conversion to driver model by using the uclass
UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not
selected:
drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata':
drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops'
or if OF_CONTROL is not selected:
arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops'
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Move CONFIG_USB_EHCI_VF to drivers/usb/host/Kconfig and update the one
and only user thereof being colibri_vf.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
There exists code in drivers/common/common.c to read the dr_mode
from the device tree. This patch converts this driver to use that
function to initialize the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.
Example of the original output:
> USB0: USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
commit 801f1fa442 "dm: usb: udc: Use SEQ_ALIAS to index the USB gadget
ports" changed the way the udevice if found. It uses the alias to find
a udevice for a given USB port number. In the commit log it was stated
that if no alias is provided, the bind order will be used instead. However
it doesn't work. Fixing this by adding a call to uclass_get_device() if
uclass_get_device_by_seq() fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
If the host does not respond in time, the initialization fails. However
the usb ether driver will still be registered. This will make
usb_gadget_probe_driver() fail the next time the initialization is
attempted because it cannot find an available UDC.
Fixing this by calling _usb_eth_halt() when the init fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on musb driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Fixes commit 0131162439 ("dm: usb: create a new UCLASS ID for USB gadget
devices")
The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.
Reported-by: Priit Laes <plaes@plaes.org>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Priit Laes <plaes@plaes.org>
Acked-by: Jagan Teki <jagan@openedev.com>
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)
To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).
If no alias is provided, then the index falls back to the order in which
the bindings took place.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
After updating the value of dev_context_ptrs[0], we should flush this
from cache to memory. Otherwise the xhci controller won't use it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When the device is in peripheral mode there is no
struct usb_bus_priv allocated pointer, as the uclass driver
("usb_dev_generic") doesn't call per_device_auto_alloc_size.
This results in writing to the internal SDRAM at
priv->desc_before_addr = true;
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
For USB3.0, the max packetsize for GET_DESCRIPTOR should be
sent as exponent value for 2. This means for 512, max packet
size should be filled with 9(2^9=512). Also, fill the USB
version field with 3.0 if speed is negotiated to Superspeed.
This fixes the issue of DFU gadget download failure with
superspeed. Without this patch, the max packet size is
overflowed to zero as the bMaxPacketsize is of u8 and hence
host is not able to detect this device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The set_phy_power() callback is part of struct omap_musb_board_data. This
structure is part of the platform data passed to the musb-new driver. This
does not really fit with the Driver Model, so allow not to use struct
omap_musb_board_data to turn the phy on or off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There don't appear to be any boards enabling CONFIG_USB_DA8XX,
and there is a newer version of the MUSB driver, so let's remove
the legacy version of it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch removes CONFIG_USB_DAVINCI. It's a legacy option
that isn't defined anywhere, and there is a newer MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When CONFIG_SPL_DM_USB was added, it was added defaulted on without
protection to ensure it didn't get set for non-DM SPL builds.
This leads to unexpected and confusing failures when building a DM based
U-Boot but with a non-DM SPL, as the defconfig is unlikely to have
CONFIG_SPL_DM_USB actively disabled.
Tweak the Kconfig to not enable this setting unless CONFIG_SPL_DM is set.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.
This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Currently it's not possible to get filesize of downloaded images and
it's impossible to automate some tasks in scripts. So this patch adds
`filesize` environment variable with size (as hex number in bytes) of
the last successfully downloaded file via `sdp` command.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.
usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The USB storage driver does not compile when CONFIG_BLK is set,
but DM_USB is not set, as we're missing the DM device links for
CONFIG_BLK enabled code paths.
So far it looks like nobody fell into this trap, because no board
enabled CONFIG_BLK and CONFIG_USB_STORAGE while not enabling
CONFIG_DM_USB, but we should still reflect that dependency properly
in Kconfig so that implicit enabling of CONFIG_USB_STORAGE works.
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This allows building the SPL without driver model for USB. Since
CONFIG_SPL_DM_USB is enabled if and only if CONFIG_DM_USB was enabled
before, this patch does not change the build behaviour.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Workaround makes FS as default mode on all affected socs.
Add support to check erratum-A005275 validity for an soc. This info is
required to determine whether a given soc is affected by this erratum.
Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used
to enable workaround for the errata
Force FS mode as default by:
- making EPS as FS
- setting PFSC bit to disable HS chirping
This workaround can be disabled by mentioning "no_erratum_a005275" in
hwconfig string
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add vbus-supply regulator support.
On some board vbus is not controlled by the phy but by
an external regulator.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add code to reset all reset signals as in usb DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add support for operating a PHY attached to ehci-pci. There are
systems where the EHCI controller is internally wired to a PCI
bus and has a PHY connected to it as well, ie. the R-Car Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
musb stop is musb core call during unregister or shutting down
gadget or host musb. For graceful exit add musb_platform_exit
on musb_stop so-that it can exit the musb platform driver as well.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
musb have platform ops to do proper graceful exit,
so add the exit call and move musb platform exit code
instead of keeping it in driver remove.
This make proper shutdown of musb where .remove will
call disable, exit serially via musb_stop.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
reset0 is not available for sun4i, 5i and 7i so access
the reset0 offset from ccm via driver data for relevant
Allwinner SoC. this will eventually drop the existing
ifdef for SUN6I.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Allocate struct phy in private structure instead of allocating
locally and assign it to a pointer. This eventually fix miss
alignment phy which is used in another functions.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add an entry in usb_gadget_controller_number() for the DWC3 gadget
controller. Without it, it is not possible to bind the USB Ethernet driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With upcoming changes that require CONFIG_BLK, this broke
USB Mass Storage on the OMAP3 boards because if CONFIG_BLK is
enabled, it assumes that DM_USB is enabled, but it wasn't yet
available on omap3 and omap4 boards.
This patch converts the OMAP2430 MUSB glue to support DM_USB and
extracts the necessary information based on the device tree.
It's based on the ti-musb driver, but there are enough significant
differences in both the architecture and device tree entires between
am33xx and OMAP3/OMAP4, that I think it makes sense to continue to
keep the separate.
Per doc/driver-model/usb-info.txt, the USB gadget stuff hasn't
migrated to DM_USB yet, so this only supports USB Host for now.
Users wanting USB Gadgets will need to disable DM_USB and leave
it the old way for now.
Signed-off-by: Adam Ford <aford173@gmail.com>
A bunch of code was encapsulated in #ifdef's whether or not
it is building or for U-Boot. Since this code is always building
for U-Boot, this patch removes the dead code.
Signed-off-by: Adam Ford <aford173@gmail.com>
As well as in K_FW_LBA_READ_10 and K_FW_LBA_ERASE_10 take device's
block size from f_rkusb->desc->blksz instead of the fixed 512 bytes.
Keep original behaviour of retry probing assigned block device on
every host request to manage late SDCard plugs.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
While downloading or uploading megabytes of data we had thousands of
printf in console like:
transfer 0x10000 bytes done
OR
Uploading 0x1000 bytes
This because transfers are chunked and there is no way on target
side to know the overall transfer size (to print one string per
overall transfer).
All these prints on serial console do slow down significantly the
transfer and does not offer a significant information to the
developer: rkdeveloptool and Rockchip original tool do use small
chunks read/writes on big transfers. This allows on workstation
to print percentage of transfer complete and as well offers to
developer the information about: transfer is running OK.
On error, either the percentage will stop or an error will be shown
on workstation console.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chip Version is a string saved in BOOTROM address space Little Endian.
Ex for rk3288: 0x33323041 0x32303134 0x30383133 0x56323030
which brings: 320A20140813V200
Note that memory version do invert MSB/LSB so printing the char
buffer would show: A02341023180002V
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Two consecutive rockusb_tx_write without waiting for request complete
do results in transfer reset of first request and thus no or incomplete
data transfer. This because rockusb_tx_write do use just one USB request
to keep serialization.
So calls like:
rockusb_tx_write_str(emmc_id);
rockusb_tx_write_csw(cbw->tag, cbw->data_transfer_length, CSW_GOOD);
was succeeding only when DEBUG was defined because the time spent
printing debug info was enough for transfer to complete.
This patch fixes the issue adding a simple request complete handler
called rockusb_tx_write_csw to be set as complete handler of in_req
when sending back simple payload + CSW replies to commands.
This new handler will always send CSW_GOOD replies because in case
of error the command callback itself must send back an error CSW as
unique reply to command.
This patch fixes execution of:
$ rkdeveloptool rfi
when DEBUG is not defined.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
After the commit 6aae84769a ("gadget: f_thor: Fix memory leaks of
usb request and its buffer"), there is hang-up with ctrl-c in some
udc. It is because req of out_ep is freed before out_ep is disabled.
Fix hang-up with ctrl-c by disabling ep before free req of the ep.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
On the A64 the clock for the first USB controller is actually the parent
of the clock for the second controller, so turning them off in that order
makes the system hang.
Fix this by only turning off *both* clocks when the *last* OHCI controller
is brought down. This covers the case when only one controller is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional usb from u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
For ohci, the maximam supported endpoint number is 32(in and out), and
now we have used (usb_pipeendpoint(pipe) << 1) to index the specified
endpoint descritor, usb_pipeendpoint(pipe) can reach 0xf, so we need
change the NUM_EDs from 8 to 32.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
ohci-hcd casts priv_data pointer to (ohci_t *), thus it must be
the first member in private data struct.
Fixes 831cc98b1 ("usb: sunxi: Simplify ccm reg base code")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
This bug is the combination of dwc2 USB controller and lan78xx
USB ethernet controller, which is the combination in use on
the Raspberry Pi Model 3 B+.
When the host attempts to receive a packet, but a packet has not
arrived, the lan78xx controller responds by setting BIR
(Bulk-In Empty Response) to NAK. Unfortunately, this hangs
the USB controller and requires the USB controller to
be reset.
The fix proposed is to have the lan78xx controller respond
by setting BIR to ZLP.
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
struct sunxi_ccm_reg doesn't have ahb_reset0_cfg on sun4i and sun5i,
thus compilation fails with:
drivers/usb/host/ohci-sunxi.c:96:26: error: 'struct sunxi_ccm_reg' has
no member named 'ahb_reset0_cfg'
Access this reg using its offset to fix this issue.
Fixes commit 1ed9c1118 ("usb: sunxi: ehci: get rid of ifdefs")
and commit 56830cee3 ("usb: sunxi: ohci: get rid of ifdefs")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
On A64 OHCI1 clock source is OHCI0 clock, so we need to enable OHCI0
clock when OHCI1 is in use.
Fixes commit dd3228170a ("usb: sunxi: Switch to use generic-phy")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
This fixes the following compiler warning:
"warning: cast from pointer to integer of different size
[-Wpointer-to-int-cast]"
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add WARN_ONCE definition to allow single time notification
of warnings to the user.
Taken from Linux kernel (4.17) with slight changes
(Removed __section(.data.once))
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
[trini: Drop the musb and dwc3 compat versions]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no reason to specify header with full soc name.
Symlink is setup automatically (arch -> arch-zynqmp)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert USB fastboot code to use shared fastboot protocol.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fb_mmc_flash_write/fb_mmc_erase/fb_nand_flash_write/fb_nand_erase to
fastboot_... as they form a public interface
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move FASTBOOT_VERSION to include/fastboot.h so when we merge the UDP code
we only have one definition.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ensure that when selecting FASTBOOT_FLASH you end up with a buildable
configuration. Prior to this you could select NAND without MTDPARTS
and end up with an image which (surprisingly) excluded NAND.
Also fix dependencies on FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME which require
you have EFI_PARTITION/DOS_PARTITION enabled.
Delete redundant FASTBOOT_FLASH_NAND_DEV from Kconfig - it was only ever
used as a guard and the value was ignored in all cases, we're using
FASTBOOT_FLASH_NAND as the guard now.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add drivers/fastboot/fb_common.c, where fastboot_okay/fail are implemented
so we can call them from a non-USB implementation.
Introduce fastboot_response which takes varargs parameters so we can
use it to generate formatted response strings. Refactor fastboot_okay/fail
to use it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add the response string as a parameter to fastboot_okay/fail, instead
of modifying a global, to match the contract expected by the AOSP
U-Boot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
There are memory leaks of usb request and its buffer for ep0,
in_ep, and out ep. Fix memory leaks of usb request and its buffer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The xhci wrapper-driver for Rockchip searches the DTS to find its
child node compatbile with 'rockchip,rk3399-usb3-phy' to retrieve the
base-address of the PHY. However, this is currently broken (and
always has been), returning NULL. However, the (wrongly) retrieved
base-address is never used.
We thus remove this code for now.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In xhci_set_configuration(), 'Context Entries' field in the slot
context was cleared with mask LAST_CTX_MASK, but it should have
taken the endianness into consideration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a full speed hub connects to a high speed hub which supports MTT,
the MTT field of its slot context will be set to 1 when xHCI driver
setups an xHCI virtual device in xhci_setup_addressable_virt_dev().
Once usb core fetch its hub descriptor, and need to update the xHC's
internal data structures for the device, the HUB field of its slot
context will be set to 1 too, meanwhile MTT is also set before, this
will cause configure endpoint command fail. In the case, we should
clear MTT to 0 for full speed hub according to section 6.2.2.
This keeps in sync with Linux kernel commit:
096b110: usb: xhci: fix config fail of FS hub behind a HS hub with MTT
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Per xHCI spec chapter 6.2.2 table 6-7, as input, software shall
initialize the dev_state field to '0'. Though this does not seem
to cause any issue with most xHC implementations, let's do this
to conform with the spec.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
If a USB 3.0 hub is plugged into the root port of the xHC, the xHCI
driver will issue a 'Configure Endpoint' command to the xHC for it
to update its internal data structure for this hub device. The hub
attributes are in the slot context so we need tell xHC to update the
slot context by setting the add context flags of the input control
context to only cover the slot context.
At present the add context flags is or'ed with the slot context bit,
but it should really be accurately set to the slot context, as the
variable that holds the value of the add context flags comes from
whatever was set in the last command execution, which may contain
additional contexts that 'Configure Endpoint' command should not
touch. Some xHC implementations like x86 don't complain such, but
it was observed on Renesas RCar Gen3 platform that the RCar xHC
complains with a 'TRB error' completion codes as the response.
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
During the execution of xhci_deregister xHCI registers are accessed. If
the clock is already deactivated when xhci_deregister is called this can
lead to undefined behavior. Change the order to deregister the device
before deactivating the clock.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Like other Allwinner SoC, the H3/H5/A64 is missing the config register
from the musb hardware block. Use a known working value for it
like other SoC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add OTG device clkgate and reset for H3/H5 through driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
with relevant fifo configs, rest all have 5 endpoints.
So add the fifo configs and defer them based on driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Filling musb_hdrc pdata using structure will unnecessary
add extra ifdefs, so fill them inside probe call for
better code understanding and get rid ifdefs using
devicetree compatible.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
- add proper macros for musb_config members
- use bool 'true' for multipoint and dyn_fifo instead of numerical 1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
devm_zalloc() is already defined in dm/device.h header, so
devm_zalloc can be removed from linux_compact.h beader file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Switch to DM_USB was done and there is no need to keep !DM_USB code in
tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to get maximum speed from dt so that usb drivers
makes use of it for DT parsing.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
(rebase and fix errors)
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is preparing dwc3 core for enabling DM_USB with peripheral
driver with using driver model support.
The driver will be bound by the DWC3 wrapper driver based on the
dr_mode device tree entry.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
(Remove dwc3-omap changes)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
During file download, it only uses 32bit variable for file size and
it limits maximum file size less than 4GB. Update to support more
than 4GB file with using two 32bit variables for file size as thor
protocol 5.0.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The thor sender can send filename without null character and it is
used without consideration of overflow. Actually, character array
for filename is assigned with DEFINE_CACHE_ALIGN_BUFFER() and it
is bigger than size of memcpy, so there was no real overflow.
Fix filename overflow for code level integrity.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
To address that situation we discussed on the list moving to
genetic_set_bit() instead.
Doing a quick grep for similar situations in drivers/usb shows that the
composite device is using __set_bit().
This patch switches over to generic_set_bit to maintain consistency between
the two gadget drivers.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
Looking at the provenance of the current u-boot code and the git change
history in the kernel, it looks like we have a local copy of set_bit and
clear_bit as a hold-over from porting the Linux driver into u-boot.
These days __set_bit and __clear_bit are optionally provided by an arch and
can be used as inputs to generic_bit_set and generic_bit_clear.
This patch switches over to generic_set_bit and generic_clear_bit to
accommodate.
Tested on i.MX WaRP7 and Intel Edison
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
If SPL serial support is disabled nothing brings in sprintf, snprintf
or simple_strtoul:
env/built-in.o: In function `regex_callback':
env/attr.c:128: undefined reference to `sprintf'
disk/built-in.o: In function `blk_get_device_by_str':
disk/part.c:386: undefined reference to `simple_strtoul'
disk/part.c:395: undefined reference to `simple_strtoul'
disk/built-in.o: In function `blk_get_device_part_str':
disk/part.c:522: undefined reference to `simple_strtoul'
disk/built-in.o: In function `part_set_generic_name':
disk/part.c:704: undefined reference to `sprintf'
drivers/built-in.o: In function `init_peripheral_ep':
drivers/usb/musb-new/musb_gadget.c:1826: undefined reference to `sprintf'
drivers/built-in.o: In function `musb_core_init':
drivers/usb/musb-new/musb_core.c:1451: undefined reference to `snprintf'
Add those dependencies here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
In case usb configuration is unknown (cdev->config == NULL), non standard
request should not be processed.
Remove also the cdev->config check below which will never happen.
This issue was seen using ums feature.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When no PHYs are declared in the dwc3 node, the phy init fails.
This patch checks if the "phys" property is presend and reports
the error returned by dev_count_phandle_with_args().
This patchs also fixes the styles issues added in last commit.
This patch should fix the DWC3 support on the UniPhier SoC family.
Fixes: 7c839ea70c ("usb: host: dwc3: Add support for multiple PHYs")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The disabled clk API returns -ENOSYS unlike the reset API returning -ENOTSUPP.
Fixes: ca7fdc8b12 ("usb: host: Add simple of glue driver for DWC3 USB Controllers integration")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
DWC3 Ips can have more than 1 PHY for USB2 and 1 PHY for USB3, add support
for a generic number of PHYs and adapt the code to handle a generic
number of PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
In order to compile the USB Ethernet gadget support we require that NET
is enabled, add that dependency here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Assigning f_rkusb->reboot_flag twice doesn't make sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The lan75xx and lan78xx drivers need to drive their phy via the generic
phylib framework. Let's reflect that dependency in Kconfig, so that we
don't get build errors when phylib does not get selected.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch increases timeout to 2s.
It was seen on 2 USB devices (Verbatim STORE N GO 070B4AED0FB22358 and
USB DISK 2.0 9000729BA41DDF40) that the request sense command takes
between 1.3s and and 1.5s.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds an interface to disable the power in dwc2 driver.
This new interface is called when the device is removed.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add generic_phy_power_on() and generic_phy_power_off()
calls to switch ON/OFF phy during probe and remove functions.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
ppc4xx support was removed some time ago. Lets remove the now unused
EHCI driver and all its references for this platform as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Marek Vasut <marex@denx.de>
DWC3 USB3 controllers will need USB3 PHY to be enabled, in addition to
USB2 PHY, to be functional. Therefore enable USB3 PHY when available.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Refractor PHY get/init/poweron and PHY poweroff/exit operations into
separate function so that its easy to support multiple PHYs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
It is wrong that expect .phy_init() to also power on the PHY. Therefore,
explicitly, call generic_phy_power_on() after generic_phy_power_init() in
order to power on PHY before using it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If we use hardware with very small RAM (let's consider just a couple
of hundreds of kB but not megabytes) it is not super convenient to lose
64kB for statically allocated bufer which most probably won't be used
as big as it is. Typically we'll have much shorter data packages to
excahnge and in the worst case longer packets will be split on separate
transactions.
For those corner-cases user will be able to set his buffer size of
choice via USB_DWC2_BUFFER_SIZE option in menuconfig.
By default we'll use 64 kB as it was hard-coeded before so existing
users shouldn't be affected at all.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
If SYS_STDIO_DEREGISTER is not selected and USB_KEYBOARD is selected
U-Boot cannot be built due to missing function stdio_deregister_dev.
So USB_KEYBOARD should select SYS_STDIO_DEREGISTER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The SDP protocol contains multiple 32bit pointers. Add a helper function
to get a valid pointer from these values and use it.
This fixes the following warnings:
drivers/usb/gadget/f_sdp.c: In function ‘sdp_rx_data_complete’:
drivers/usb/gadget/f_sdp.c:347:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy((void *)sdp->dnl_address, req->buf + 1, datalen);
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_jump_imxheader’:
drivers/usb/gadget/f_sdp.c:625:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
entry = (void *)headerv2->entry;
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_handle_in_ep’:
drivers/usb/gadget/f_sdp.c:668:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy(&data[1], (void *)sdp_func->dnl_address, datalen);
^
drivers/usb/gadget/f_sdp.c:679:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
status = sdp_jump_imxheader((void *)sdp_func->jmp_address);
^
Signed-off-by: Andre Heider <a.heider@gmail.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
'default' on a choice refers to the symbol selected by default, not to
the choice mode, so 'default n' is meaningless.
No functional changes. Optional choices implicitly default to n mode
(and there is no way to make them default to another mode).
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection n (undefined) of <choice> (defined at drivers/usb/ulpi/Kconfig:3) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int. For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long. For the long term
we should however change the declaration of dma_buf.
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable hcd_name is unsued, drop.
Cc: Marek Vasut <marex@denx.de>
Cc: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
ehci_writel() swaps the arguments for address and value. One call
in ehci-mxs ignores that.
This fixes the warning:
drivers/usb/host/ehci-mxs.c: In function ?ehci_hcd_stop?:
drivers/usb/host/ehci-mxs.c:159:19: error: initialization makes integer from pointer without a cast [-Werror=int-conversion]
ehci_writel(tmp, &hcor->or_usbcmd);
^
arch/arm/include/asm/io.h:117:34: note: in definition of macro ?writel?
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/usb/host/ehci-mxs.c:159:2: note: in expansion of macro ?ehci_writel?
^~~~~~~~~~~
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Bool initializations should use true and false.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_HCD
CONFIG_USB_MUSB_UDC
CONFIG_USB_DAVINCI
CONFIG_USB_OMAP3
CONFIG_USB_DA8XX
CONFIG_USB_AM35X
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY
Signed-off-by: Adam Ford <aford173@gmail.com>
this patch implement rockusb protocol on the device side. this is based on
USB download gadget infrastructure. the rockusb function implements the rd,
wl, rid commands. it can work with rkdeveloptool
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the musb sunxi glue driver is completely device model / device
tree driven, we should use the base address from the device tree,
instead of hard-coding it in the source code.
Fixes: 3a61b080ac ("musb: sunxi: switch to the device model")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
When enable CONFIG_HAS_FSL_DR_USB, we might encounter below compile
warning, apply this patch can fix it:
drivers/usb/host/ehci-fsl.c:109:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
((u32)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
^
drivers/usb/host/ehci-fsl.c:108:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
hcor = (struct ehci_hcor *)
^
drivers/usb/host/ehci-fsl.c:115:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
drivers/usb/host/ehci-fsl.c:115:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
While the USB HW in the RZ/A is basically the same, there are some
differences from the original versions that were in the SH SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
This prevents board resets when calling sdp command on boards which have a watchdog.
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Increase the buffer length to be just above maximum permissible value
of 128 kiB . This increases the performance of the UMS and alike by a
factor of 2 - 2.5 as the buffers are less fragmented.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
Its a valid use case to call ehci_submit_async() with a NULL buffer
with length 0. E.g. from usb_set_configuration().
As invalidate_dcache_range() isn't able to judge if the address
NULL is valid or not (depending on the SoC hardware configuration it
might be valid) do the check in ehci_submit_async() as here we know
that we don't have to invalidate such a buffer.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Currently we check in ehci_shutdown() if ctrl is NULL after
dereferencing it.
Before this we have already dereferenced ctrl, ctrl->hccr,
and ctrl->hcor in ehci_get_portsc_register(), ehci_submit_root(),
and hci_common_init().
A better approach is to already check ctrl, ctrl->hccr, and ctrl->hcor
during the initialization in ehci_register() and usb_lowlevel_init()
and signal an error here via the return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car
Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+
and R8A7796 are supported.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Commit 9000eddbae ("drivers/usb/ehci: Use platform-specific accessors")
broke USB 2.0 on big-endian platforms because for them writel/readl()
does automatic conversion of BE data to LE.
Proper implementation requires to use "raw" variant of these accessors
which read/write data without messing with endianess.
While at it replace cpu_to_be32() to be32_to_cpu() in readl() to
keep sane semantics.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Reported-by: Vladimir Boroda <boroda@yahoo.com>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
use Kconfig to select xhci accordingly.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Including <common.h> pulls in a lot of bloat. What this driver needs
is BIT(), so replace it with <linux/bitops.h>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Collect runtime BUG/WARN into a self-contained header <linux/bug.h>
to make these macros easier to use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*(). U-Boot does not support them in a clean
way. So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.
We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround. Hence this
patch, to find the best home for all printk variants. If you want to
use printk() and friends, please include <linux/printk.h>. This header
is self-contained, and pulls in only a few headers.
When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards. This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.
To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel". (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.
The difference is the loglevel is build-time determined. To save the
image size, lower priority pr_*() are compiled out. I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.
I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since we use EHCI generic driver on RCar Gen3 , this driver is useless.
Remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
USB_GADGET will fail to compile if USB_MUSB_GADGET is not defined. Make
sure we have that condition right.
Fixes: e0ea88042d51 ("sunxi: Imply USB_ETHER")
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.
Switch to probing both in peripheral and host mode through the DT.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the Allwinner boards use the same manufacturer, VID and PID for the
gadgets. Make them the defaults to remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usb_ether gadget duplicates the USB settings for the manufacturer,
product ID and vendor ID.
Make sure we use the common option so that we can expect a single VID/PID
couple for a single device.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We need to select an interface for the usb_ether gadget, and they haven't
been converted to Kconfig yet. Add a choice to make sure we have an option
selected, and convert all the users.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB Ethernet gadget option has not yet been moved to Kconfig, let's
deal with that.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While the USB Ethernet device address is already defined in Kconfig, the
host address isn't. Convert it.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an help about the USBNET_DEVADDR Kconfig option to make it clearer what
it's about.
Acked-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USBNET_DEVADDR has nothing to do with the USB download gadget, but
rather with the USB Ethernet gadget. Move it out of the if statement.
Acked-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The 'Max Burst Size' indicates to the xHC the maximum number of
consecutive USB transactions that should be executed per scheduling
opportunity. This is a “zero-based” value, where 0 to 15 represents
burst sizes of 1 to 16, but at present this is always set to zero.
Let's program the required value according to real needs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
USB endpoint reports the period between consecutive requests to send
or receive data as bInverval in its endpoint descriptor. So far this
is ignored by xHCI driver and the 'Interval' field in xHC's endpoint
context is always programmed to zero which means 1ms for low speed
or full speed , or 125us for high speed or super speed. We should
honor the interval by getting it from endpoint descriptor.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
In xhci_check_maxpacket(), the control endpoint 0 max packet size
is wrongly taken from the interface's endpoint descriptor. However
the default endpoint 0 does not come with an endpoint descriptor
hence is not included in the interface structure. Change to use
epmaxpacketin[0] instead.
The other bug in this routine is that when setting max packet size
to the xHC endpoint 0 context, it does not clear its previous value
at all before programming a new one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
xHCI uses normal TRBs for both bulk and interrupt. This adds the
missing interrupt transfer support to xHCI so that devices like
USB keyboard that uses interrupt transfer can work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present xHCI driver assumes LS/FS devices are attached directly
to a HS hub. If they are connected to a LS/FS hub, the driver will
fail to perform the USB enumeration process on such devices.
This is fixed by looking from the device itself all the way up to
the HS hub where the TT that serves the device is located.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With the root hub unbinding in usb_stop(), there is no need to do
a Sandbox-specific reset operation. usb_emul_reset() is no longer
used anywhere, drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
