This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This should reduce the size of the struct, and also groups more similar
fields together.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A few registers had slightly different names from what is in the datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using an fdt-specific function causes problems when compiled with a live
tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@oktetlabs.ru>
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07eedf ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
u_boot should be u-boot
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to the mx25l12805d datasheet it supports using 4K or 64K sectors.
So lets add the SECT_4K to enable 4K sector usage.
Datasheet: https://www.mxic.com.tw/Lists/Datasheet/Attachments/7321/MX25L12805D,%203V,%20128Mb,%20v1.2.pdf
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Define LOG_CATEGORY and change printf and pr_*
to dev_ (when dev is available) or log_ macro.
This patch adds the support of logging feature with log command
(filtering, display of device name in trace) and allows to
suppress traces via the syslog driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI/DM_SPI_FLASH with a related config option.
Build fine, but not tested.
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI/DM_SPI_FLASH with associated config
options.
Build fine, but not tested.
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Remove the redundant setting for USB_RX_EARLY_SIZE. Besides, for
RTL8153B, it is necessary to notify the hardware of the changes
of the aggregation settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
The r8152_eth_probe() may allocate a memory for ss->dev_priv.
It has to be freed if r8152_eth_probe() fails finally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
For bulk IN transfer, the codes will set ISP flag to request event TRB
being generated by xHC for the case of short packet. So when encountering
buffer-cross-64K-boundary (which we will divide payload and enqueuqe
more than 1 transfer TRB), and the first TRB ends up with a short packet
condition it will trigger an short packet code transfer event per that
flag and cause more than 1 event TRB generated for this transfer.
However, current codes will only handle the first transfer event TRB
then mark current transfer completed, causing next transfer
failure due to event TRB mis-match.
Such issue has been observed on some Layerscape platforms (LS1028A,
LS1088A, etc) with USB ethernet device.
This patch adds a loop to make sure the event TRB for last transfer TRB
has been handled in time.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
DM is the modern default approach for the drivers in U-Boot.
It also allows to configure code via Device Tree.
Move Intel Edison to use DM_USB_GADGET and drop hard coded values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use generic Synopsys DesignWare 3 driver on Intel Edison.
For now it's just a stub which allows future refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The platforms based on Intel Tangier may have different requirements
how to create bootloader bundle to supply to a device. Currently
the BINMAN approach is for Intel Edison only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Like in the rest of x86 boards append CPU to the board compatible string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
None of the driver for Edison is using DM_PCI_COMPAT, hence drop it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It appears that U-Boot works by luck on Intel Edison board because the amount
of RAM is less than 1 GB and standard way of calculating the top of it work
for this configuration. However, this won't work if the amount of RAM is
different and split differently in address space. We have to find the suitable
window correctly.
Find proper memory region for relocation by scanning MMAP SFI table in
board_get_usable_ram_top() callback.
According to the address map documentation the Main Memory is guaranteed to lie
in the 0..2 GB range, that's why we limit search by this range.
Fixes: e71de54a49 ("x86: Add Intel Tangier support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed a typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Make use of the new bootargs substitution mechanism and zboot command
syntax.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With the updated changes to bootargs substitution[1], the zboot command
needs to be updated to get its command line from an environment variable
instead of a memory address. This is because the command-line string must
be updated to convert %U to ${uuid}, etc.
In any case it is more flexible to use a environment variable and it is
best to do this before the release to avoid a subsequent change.
Update the command accordingly.
[1] http://patchwork.ozlabs.org/project/uboot/list/?series=212481
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move several README files to reStructured text for the HTML documentation.
Describe register for global data on x86.
Allow building HTML documentation with Sphinx 3
-----BEGIN PGP SIGNATURE-----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=dRaN
-----END PGP SIGNATURE-----
Merge tag 'doc-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Documentation fixes for v2020.01-rc4
Move several README files to reStructured text for the HTML documentation.
Describe register for global data on x86.
Allow building HTML documentation with Sphinx 3
Set $devtype for DHCP boot, which can be handy for the boot.scr
for detection of devtype used (for example, when the same boot.scr is
used for both mmc/dhcp boot):
if test ${devtype} = "dhcp"; then
...
fi
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Convert README.bootmenu to reStructured text and move it to
usage/bootmenu.rst.
Adjust the text concerning configuration settings as these now are managed
via Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Convert README.trace to reStructured text and move it to develop/trace.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert README.NetConsole to reStructured text and move it to
doc/usage/netconsole.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reformat README.commands as reStructured text and add it to the HTML
documentation as develop/commands.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to removed function c_funcptr_sig_re building with Sphinx 3 fails.
With the patch building succeeds with a lot of warnings if the '-W' flag is
removed from doc/Makefile. Most of the documentation is correct
This follows the approach taken by the Linux kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On x86 the global data pointer is stored in register fs.
On x86_64 no register is used for the global data pointer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver model big rename for consistency
Python 3 clean-ups for patman
Update sandbox serial driver to use membuff
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/Xcu0RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZGpQgAqD7JsdNRHVKe2LEnYBR0sY1hlPH0+fz/
UW9hjpp3DTHasFc5w1pa6GJjJvexc0PqQnN3TSRz6+bQyhtIyvJUbqCbU9g2ApBu
3NIHipAa2kqD8B5WpWX6mMkBH5Vx9pAmrTV6oGt+MurEWoQ0M4SnaAkcnZqqLdHf
+fpiIDB/Kw1dnpWaleZSdZIJ4bPQaBkLcYIE3+jGrmcX+S5G8ZMH59MfVNZuzxfE
GpD+oRhkhjdDRr9MyRoTPvvALzF3Q+uo1HYbyYmyoOG7h3xCzcDqmkO4/NlZmhbV
T295C70d5rVDb8LFxinXlQ7fMLajjrwL4FVYMYADKQKK/IiKb7BJBQ==
=5uBK
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-14dec20' of git://git.denx.de/u-boot-dm into next
Driver model tidy-up for livetree
Driver model big rename for consistency
Python 3 clean-ups for patman
Update sandbox serial driver to use membuff
- Fix wrong amoswap t1 usage in startup.
- Reset the board after crash.
- Enable distro booting from an attached SCSI disk for QEMU.
- Support the optional header fields in efi header.
