Commit graph

76341 commits

Author SHA1 Message Date
Samuel Holland
8b0eacdf2b sunxi: pmic_bus: Use the DM PMIC interface when possible
The pmic_bus functions are used in both SPL (for regulator setup) and
U-Boot proper (for regulator setup, SID access, GPIO, and poweroff).

Currently, pmic_bus conflicts with DM_I2C because it uses the legacy I2C
interface. This commit makes pmic_bus dual-compatible with either the
legacy I2C functions or the newly-added PMIC_AXP driver (which uses
DM_I2C). In turn, this allows platforms to start transitioning to DM_I2C
in U-Boot proper, without breaking boards that still depend on the
legacy I2C interface for other reasons.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 10:48:37 +01:00
Samuel Holland
d3b02987cb sunxi: pmic_bus: Clean up preprocessor conditions
Instead of using the SoC symbols to decide the bus type, use whichever
bus driver is actually enabled. This allows collapsing all of the AXP2xx
and AXP8xx variants into one "else" case. It also has the advantage of
falling back to I2C when the other bus drivers are disabled; this works
because all of the PMICs support I2C in addition to other interfaces.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 10:30:19 +01:00
Samuel Holland
3227c85fe7 i2c: Add a DM_I2C driver for the sun8i RSB controller
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.

Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.

The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.

There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 10:19:18 +01:00
Samuel Holland
104950a7fe i2c: Add a DM_I2C driver for the sun6i P2WI controller
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.

Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.

The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:50:56 +01:00
Samuel Holland
4ab39e74b6 sunxi: pmic_bus: Fix Kconfig dependencies
AXP_PMIC_BUS enables communication with a specific AXP PMIC at a
PMIC-dependent I2C/P2WI/RSB bus address. It is automatically selected
as a dependency of the PMIC driver. It should not be selectable by the
user when no PMIC is chosen.

AXP_GPIO uses the pmic_bus functions, and also depends on a specific
PMIC header to pick up register definitions.

Both of these changes have no impact on any existing configs, since
the code does not compile if the dependencies are not met.

Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:50:27 +01:00
Samuel Holland
abd2e783f1 sunxi: Select SUN8I_RSB more carefully
SUN8I_RSB should not be selected by MACH_SUN8I, because the hardware
is not present in half of those SoCs (H3/H5, R40, and V3s). Move the
selection to the SoCs where the hardware actually exists.
As it currently stands, selecting that option also requires using it in
some way, which is not the case for one A80 board. Since we have only
three A80 boards in total, we select it their via their defconfigs.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixing up Sunchip_CX-A99 build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:50:21 +01:00
Samuel Holland
ea261fdeb2 sunxi: Only initialize legacy I2C when enabled
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level
Kconfig symbol (not specific to either legacy or DM I2C), whereas the
i2c_init() function is specific to legacy I2C. This change fixes a
build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:49:09 +01:00
Samuel Holland
526c4f2e43 power: pmic: Add a driver for X-Powers AXP PMICs
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.

Enable the driver by default for SoCs that normally pair with a PMIC.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:41:57 +01:00
Samuel Holland
3fd90e43d9 power: pmic: Consistently depend on SPL_DM_PMIC
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:36:02 +01:00
Samuel Holland
7f51b554be power: pmic: Consistently depend on DM_PMIC
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.

Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:35:41 +01:00
Tom Rini
4c1996ce37 Merge branch '2021-10-11-TI-platform-updates'
- Assorted TI platform updates
2021-10-11 22:39:27 -04:00
Jan Kiszka
08ad739f38 arm: dts: Update IOT2050 device tree files
This fixes the usage of the USB 3.0-capable port under U-Boot as USB
2.0-only port.

Original patch by Chao Zeng.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-11 15:02:50 -04:00
Jan Kiszka
ce543d0d4e board: siemens: iot2050: Adjust to changes in DT and configuration
Account for the changes done between merge proposal and the final merge.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-10-11 15:02:50 -04:00
Adam Ford
5134f79ee6 ARM: omap3_logic: Cleanup usage of MUX_VAL
The macro called MUX_VAL generates a writel instruction with
semicolon at the end.  This table was written to use semicolons,
however one was missed:

   MUX_VAL(CP(SYS_BOOT2),      (IEN  | PTD | DIS | M4))    /* GPIO_4 */

Since the extra semicolon is unnecessary with the use of the macro,
remove all of them, and cleanup whitespace.

Reviewed-by: Wolfgang Denk <wd@denx.de>
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
2021-10-11 15:02:50 -04:00
Dario Binacchi
165e8fe5db clk: ti: add am33xx/am43xx spread spectrum clock support
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.

Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.

In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.

Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Dario Binacchi
15a0411787 ARM: dts: am43xx-clocks: add spread spectrum support
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).

Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Dario Binacchi
bf4a54fa78 ARM: dts: am33xx-clocks: add spread spectrum support
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).

Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-10-11 14:27:32 -04:00
Adam Ford
56c7f882ee configs: omap3x_logic: Enable LTO on more LogicPD OMAP3 boards
There are five omap3 based boards from LogicPD.  Two of them
have added LTO support. Add the remaining three to use LTO.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-10-11 14:27:32 -04:00
Chukun Pan
e7510d24ca sunxi: Add support for FriendlyARM NanoPi R1S H5
This adds support for the NanoPi R1S H5 board.

Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED

The dts file is taken from Linux 5.14 tag.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
23c83366f3 clk: sunxi: Add drivers for A31 and H6 PRCM CCUs
Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
c61897bf02 clk: sunxi: Add support for I2C gates/resets
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
8fe8ff3411 sunxi: gpio: Remove bank-specific size macros
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
4d9958b642 sunxi: gpio: Remove name_to_gpio macro
This clarifies which callers must be updated to complete the DM_GPIO
conversion.

The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
425084610e sunxi: Clean up inclusions of asm/arch/gpio.h
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.

Some files did not contain any GPIO code at all, so this header was
completely unused.

A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.

The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Arnaud Ferraris
0534153fd1 pinephone_defconfig: add support for early-boot status LED
This commit enables the green status LED (PD18/GPIO 114) on boot in the
SPL, in order to provide visual feedback that the PinePhone is booting.

Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Arnaud Ferraris
8f872bb37d board: sunxi: enable status LED early
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.

In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.

Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
14c8c631e9 gpio: sunxi: Remove the sunxi_name_to_gpio_bank function
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
dda9fa734f sunxi: Simplify MMC pinmux selection
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.

This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Samuel Holland
21d314a661 clk: sunxi: Move header out of arch directory
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Arnaud Ferraris
5427da02be configs: add PineTab defconfig
The PineTab device-tree is already in u-boot, this commit adds the
corresponding defconfig, based on pinephone_defconfig.

Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:43 +01:00
Tom Rini
f331497d3a - add 30bpp support (EFI, simplefb, vidconsole)
- fix video console name in CONSOLE_MUX Kconfig help
  - move mxsfb driver config option to Kconfig
  - remove unused mx3fb driver
 -----BEGIN PGP SIGNATURE-----
 
 iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYWHeIw4cYWd1c3RAZGVu
 eC5kZQAKCRBM6ATMmsalXPMXAJsEn/v2k7xaWSjP11DfkPdoj2rmGQCeIijNt60a
 4UNYJe3S4pPBiNMamJo=
 =spnC
 -----END PGP SIGNATURE-----

Merge tag 'video-20211009' of https://source.denx.de/u-boot/custodians/u-boot-video

 - add 30bpp support (EFI, simplefb, vidconsole)
 - fix video console name in CONSOLE_MUX Kconfig help
 - move mxsfb driver config option to Kconfig
 - remove unused mx3fb driver

# gpg verification failed.
2021-10-09 17:47:27 -04:00
Anatolij Gustschin
79c05335a9 video: move MXS to Kconfig
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-09 19:50:03 +02:00
Anatolij Gustschin
450d937812 video: remove not used mx3fb driver
i.MX31 support was removed, and the non dm-video driver
is obsolete and not used. Remove it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2021-10-09 19:42:32 +02:00
Anatolij Gustschin
de99e776b8 common: Kconfig: use 'vidconsole' name instead of old 'video'
After DM_VIDEO conversion the 'vidconsole' is the correct name
for the frame buffer console. 'video' will not work, so update
the description of the config option.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2021-10-09 19:41:33 +02:00
Simon Glass
2a2d8e94dd lz4: Use a private header for U-Boot
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.

Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-09 13:09:56 -04:00
Mark Kettenis
79f9defeba efi_loader: GOP: Fix 30bpp block transfer support
Convert pixel values when necessary like we do for 16bpp
framebuffers.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-10-09 18:50:31 +02:00
Mark Kettenis
2c2653d6f9 video: simplefb: Add 30bpp support
Recognize the canonical format strings for framebuffers in
30bpp mode and 32/24bpp mode.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
2021-10-09 18:48:25 +02:00
Mark Kettenis
01fcf0eea6 efi_loader: GOP: Add 30bpp support
Provide correct framebuffer information for 30bpp modes.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
2021-10-09 18:46:13 +02:00
Mark Kettenis
0efe41ca15 video: Add 30bpp support
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
2021-10-09 18:43:51 +02:00
Tom Rini
94e922c76a Merge branch '2021-10-08-image-cleanups'
- A large number of image file and tooling related cleanups
2021-10-08 16:02:55 -04:00
Simon Glass
4cb35b7a1f image: Split up boot_get_fdt()
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the FDT into a separate function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
a2198cd018 image: Reduce variable scope in boot_get_fdt()
Move the variables declarations to where they are needed, to reduce the
number of #ifdefs needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
b53541f7f6 image: Remove some #ifdefs from image-fit and image-fit-sig
Drop the #ifdefs which are easy to remove without refactoring.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
f33a2c1bd0 image: Remove #ifdefs from select_ramdisk()
Use boolean variables to deal with the strange #ifdef logic of this
function, so we can remove the #ifdefs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
e4c928792e image: Split up boot_get_ramdisk()
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the ramdisk into a separate function.

Leave the code indented as it was for easier review. The next patch cleans
this up along with checkpatch violations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
78f88790e3 image: Reduce variable scope in boot_get_ramdisk()
Move the variables declarations to where they are needed, to reduce the
number of #ifdefs needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
1df654a6af image: Drop most #ifdefs in image-board.c
Remove ifdefs in this file, so far as possible without too much
refactoring.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
78740bcce8 image: Drop #ifdefs for fit_print_contents()
Use a simple return to drop the unwanted code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
13c133b995 image: Drop unnecessary #ifdefs from image.h
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00
Simon Glass
0ab5e02704 image: Tidy up fit_unsupported_reset()
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.

Drop fit_unsupported() since it is not used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-10-08 15:53:27 -04:00