Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch is based on the following patch sent a few minutes ago:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
It is untested, of course. Anton, could you please give it a try.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen
controller and FHCI (QE USB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
