Commit graph

20 commits

Author SHA1 Message Date
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Russ Dill
025a0d40e1 ARM: am33xx: Inhibit re-initialization of DDR during RTC-only
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
2018-04-06 17:04:33 -04:00
Tero Kristo
7619badb9c ARM: AM43xx: Add support for RTC only + DDR in self-refresh mode
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.

The RTC scratch register layout used is:

SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader

During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.

RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06 17:04:33 -04:00
Faiz Abbas
b442e16b87 am33xx: board: Call spl_early_init() to support sdram_init()
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-28 12:27:33 -05:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Alexandru Gagniuc
409a81ddd4 am33xx: board: Refactor USB initialization into separate function
The declaration of otg*_plat and otg*_board_data is guarded by
CONFIG_USB_MUSB_*, but their use in arch_misc_init is not. The
ifdef flow goes something like:

if (CONFIG_USB_MUSB_* && other_conditions)
	declare usb_data
if (other_conditions)
	use usb_data

Thus when CONFIG_USB_MUSB_* is not declared, we try to use the
data structures, but these structures aren't defined.

To fix this, move the USB initialization code into the same #ifdef
which guards the declaration of the data structures. Since the DM_USB
vs legacy cases are completely different, use two versions of
arch_misc_init(), for readability.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-11 22:49:39 -04:00
Lokesh Vutla
4bd754d8ab arm: omap: Detect boot mode very early
ROM stores the boot params information in a known location
and passes it to SPL. This information needs to be copied
very early during boot or else there is a chance of getting
corrupted by SPL. So move this boot device detection very early
during boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-10 14:26:04 -04:00
Semen Protsenko
00bbe96eba arm: omap: Unify get_device_type() function
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.

Details:
 - Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
   OMAP4/5), so we can obtain status register in common way
 - For now ctrl structure for AM33xx/OMAP3 contains only status register
   address
 - Run hw_data_init() in order to assign ctrl to proper structure
 - Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
   (DEVICE_TYPE_MASK and GP_DEVICE are used instead)
 - Guard structs in omap_common.h with #ifdefs, because otherwise
   including omap_common.h on non-omap4/5 board files breaks compilation

Buildman script was run for all OMAP boards. Result output:
    arm: (for 38/616 boards)
        all +352.5
        bss -1.4
        data +3.5
        rodata +300.0
        spl/u-boot-spl:all +284.7
        spl/u-boot-spl:data +2.2
        spl/u-boot-spl:rodata +252.0
        spl/u-boot-spl:text +30.5
        text +50.4
    (no errors to report)

Tested on AM57x EVM and BeagleBoard xM.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-09 20:34:53 -04:00
Tom Rini
8627733941 ti816x: Rework DDR initialization sequence
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family.  In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations.  Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient.  Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still.  As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it.  We also remove a bunch
of other untested code about changing the speed the DDR runs at.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Lokesh Vutla
878d885620 arm: amx3xx: Add support for early debug
For early debug, the following configs needs to be enabled:

CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_BASE=0x44e09000
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:15 -04:00
Lokesh Vutla
fbd6295da4 arm: am33xx: Add support for mulitiple PLL input frequencies
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-12 08:37:14 -04:00
Lokesh Vutla
86282798b0 arch: arm: omap: Declare size of ddr very early
Declare the size of ddr very early in spl, so that this can be
used to enable cache.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
2017-05-11 22:03:41 -04:00
Jean-Jacques Hiblot
d5abcf94c7 ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-19 22:17:14 -04:00
Heiko Schocher
17fa032671 serial, ns16550: bugfix: ns16550 fifo not enabled
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.

Since the above patch, you have to setup the fcr register.

For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...

This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.

Detected this issue with automated tbot tests on am335x
based shc board.

The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)

Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-20 09:15:19 -05:00
Masahiro Yamada
1d2c0506d3 mmc: move more driver config options to Kconfig
Move (and rename) the following CONFIG options to Kconfig:

  CONFIG_DAVINCI_MMC  (renamed to CONFIG_MMC_DAVINCI)
  CONFIG_OMAP_HSMMC   (renamed to CONFIG_MMC_OMAP_HS)
  CONFIG_MXC_MMC      (renamed to CONFIG_MMC_MXC)
  CONFIG_MXS_MMC      (renamed to CONFIG_MMC_MXS)
  CONFIG_TEGRA_MMC    (renamed to CONFIG_MMC_SDHCI_TEGRA)
  CONFIG_SUNXI_MMC    (renamed to CONFIG_MMC_SUNXI)

They are the same option names as used in Linux.

This commit was created as follows:

[1] Rename the options with the following command:

find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'

[2] Commit the changes

[3] Create entries in driver/mmc/Kconfig.
    (copied from Linux)

[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI

[5] Sort and align drivers/mmc/Makefile for readability

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2017-01-11 19:40:15 +09:00
Mugunthan V N
ba7916c72f am33xx: board: init usb ether gadget for rndis support
Add usb ether gadget device with usb_ether_init() when
CONFIG_DM_ETH and CONFIG_USB_ETHER are defined.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-09 11:16:22 -07:00
Mugunthan V N
1cac34ce16 drivers: usb: musb: adopt musb backend driver to driver model
Currently all backend driver ops uses hard coded physical
address, so to adopt the driver to DM, add device pointer to ops
call backs so that drivers can get physical addresses from the
usb driver priv/plat data.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-02 21:04:48 -07:00
Mugunthan V N
3aec264869 am33xx: board: probe misc drivers to register musb devices
MUSB wrapper driver is bound as MISC device and underlying usb
devices are bind to usb drivers based on dr_mode, so probing the
MISC wrapper driver to register musb devices.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-02 21:04:07 -07:00
Mugunthan V N
195702217d am33xx: board: do not register usb devices when CONFIG_DM_USB is defined
Do not register usb devices when CONFIG_DM_USB is define.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-02 21:03:56 -07:00
Tom Rini
983e37007d arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Renamed from arch/arm/cpu/armv7/am33xx/board.c (Browse further)