Commit graph

150 commits

Author SHA1 Message Date
Eugen Hristev
0c66872f99 net: remove unused CONFIG_DRIVER_AT91EMAC_*
AT91EMAC driver is unused, thus removing.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-21 10:08:24 +03:00
Simon Glass
9f6649209f net: Move network rules to drivers/net
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another.  Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs.  Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.

Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-04 12:51:47 -04:00
Ashok Reddy Soma
258ce79cfc net: xilinx: axi_mrmac: Add MRMAC driver
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.

Tested 10G and 25G on all 4 ports.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:18:45 +02:00
Tim Harvey
668e205098 net: add support for KSZ9477/KSZ9897/KSZ9567 GbE switch
The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches
support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO.

This driver currently supports I2C register access but SPI or MDIO register
access can be easily added at a later time.

Tagging is not implemented and instead the active port is tracked to
avoid needing a tag to store port information.

This was tested with the imx8mm-venice-gw7901 board which has a
KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-07-10 18:12:42 +02:00
Jassi Brar
eab447b2b5 net: synquacer: Add netsec driver
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-06-18 11:29:17 +03:00
Tom Rini
aee18604e2 net: Remove ne2000 driver
With the last user of this driver removed, remove the driver.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-05-25 12:40:16 -04:00
Claudiu Manoil
ff98da0667 sandbox: Add a DSA sandbox driver and unit test
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.

The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver.  The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports.  To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time.  So pinging through
these switch ports is as easy as:

=> setenv ethact lan0
=> ping 1.2.3.5

Unit tests for the dsa class code were also added.  The 'dsa_probe'
test exercises most API functions from dsa.h.  The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.

I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-04-15 14:22:17 +05:30
Neil Armstrong
798424e857 net: designware: add Amlogic Meson8b & later glue driver
This adds a proper glue driver for the Designware DWMAC ethernet MAC IP
found in the Amlogic Meson8, GXBB, GXL, GXM, G12A, G12B & SM1 SoCs.

This is aimed to replace the static ethernet link setup found on the board
init code for the Amlogic SoC based boards.

Tested on a libretech-cc (S905x Internal RMII 10/100 PHY) and Khadas VIM3 (A113d
with external 10/100/1000 RGMII PHY) to cover the most extreme setups.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-04-06 11:10:29 +02:00
Neil Armstrong
8120ce17bf net: add Amlogic Meson G12A MDIO MUX driver
The Amlogic G12A & compatible SoCs embeds a mux to either communicate with
the external PHY or the internal 10/100 PHY.

This adds support for this mux as a MDIO MUX device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-04-06 11:10:29 +02:00
Neil Armstrong
6c7bc9fec0 net: add MMIO Register MDIO MUX driver
Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-04-06 11:10:29 +02:00
Tom Rini
215386e48c sh: Remove r7780mp board
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15 10:16:23 -05:00
Aaron Tseng
febe13b438 net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs
Add Cortina Access Ethernet device driver for CAxxxx SoCs.
This driver supports both legacy and DM_ETH network models.

Signed-off-by: Aaron Tseng <aaron.tseng@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>

CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Abbie Chang <abbie.chang@Cortina-Access.com>
CC: Tom Rini <trini@konsulko.com>
2021-01-27 10:47:44 -05:00
Weijie Gao
17ade70b6a net: add ethernet driver for MediaTek MT7620 SoC
This patch adds  ethernet driver for MediaTek MT7620 SoC.

The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).

The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.

This driver supports MT7530 giga switch connects to port 5.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24 21:39:27 +01:00
Robert Marko
975151d056 net: Add IPQ40xx MDIO driver
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2020-10-22 09:54:54 -04:00
Suneel Garapati
4684a7a43a net: Add NIC controller driver for OcteonTX2
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.

Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-10-14 07:55:56 +02:00
Suneel Garapati
0008e9a69d net: Add NIC controller driver for OcteonTX
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.

Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2020-10-14 07:55:56 +02:00
Heiko Schocher
6e31c62a17 net, qe: add DM support for QE UEC ethernet
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.

Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>

Series-changes: 3
- revert:
  commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
  as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger

Series-changes: 2
- add comments from Qiang Zhao:
  - add device node documentation
  - I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
    because using drivers/net/fsl_mdio.c leads in none existent
    udevice mdio@3320
    instead boards with DM ETH support should use now this
    driver.
- remove RFC tag

Commit-notes:

- I let the old none DM based implementation in code
  so boards should work with old implementation.
  This Code should be removed if all boards are converted
  to DM/DTS.

- add the DM based qe uec driver under drivers/net/qe

- Therefore copied the files uccf.c uccf.h uec.h from
  drivers/qe. So there are a lot of Codingstyle problems
  currently. I fix them in next version if this RFC
  patch is OK or it needs some changes.

- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
  Used a lot of functions from drivers/qe/uec.c

- seperated the PHY specific code into seperate file
  drivers/net/qe/dm_qe_uec_phy.c

END
2020-09-17 06:09:53 +02:00
Amit Singh Tomar
3c5c4ee35f net: designware: s700: Add glue code for S700 mac
This patchs adds glue logic to enable designware mac present on
Action Semi based S700 SoC, Configures SoC specific bits.

Undocumented bit that programs the PHY interface select register
comes from vendor source.

It has been tested on Cubieboard7-lite based on S700 SoC.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
2020-07-07 17:11:58 -04:00
Ye Li
5fe419ef2a net: Add eth phy generic driver for shared MDIO
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.

To resolve this problem, introduce an eth phy generic driver and uclass.

After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.

When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 13:24:48 +02:00
Ioana Ciornei
52e16ec613 drivers: net: add Layerscape mEMAC MDIO driver
Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-29 10:49:20 +05:30
Amit Singh Tomar
d53e3fa385 net: Add support for Broadcom GENETv5 Ethernet controller
The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs
and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4.
There is no publicly available documentation, so this driver is based
on the Linux driver. Compared to that the queue management is
drastically simplified, also we only support version 5 of the IP and
RGMII connections between MAC and PHY, as used on the RPi4.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: heavy cleanup and a few fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-01-29 18:30:33 +01:00
Alex Marginean
8bd37ce3cd drivers: net: add marvell MDIO driver
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers based on driver model. There are two
reasons to have a separate driver rather than including it inside
the MAC driver itself:
  *) The MDIO interface is shared by all Ethernet ports, so a driver
     must guarantee non-concurrent accesses to this MDIO interface. The
     most logical way is to have a separate driver that handles this
     single MDIO interface, used by all Ethernet ports.
  *) The MDIO interface is the same between the existing mv643xx_eth
     driver and the new mvneta/mvpp2 driver. Even though it is for now
     only used by the mvneta/mvpp2 driver, it will in the future be
     used by the mv643xx_eth driver as well.

This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE
802.3 Clause 45.

This patch also adds device tree binding for marvell MDIO driver.

Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-09-04 11:37:19 -05:00
Alex Marginean
74dd383867 drivers: net: driver for MDIO muxes controlled over I2C
This driver is used for MDIO muxes driven over I2C.  This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-04 11:37:19 -05:00
Joe Hershberger
bb53ae38de Revert "drivers: net: driver for MDIO muxes controlled over I2C"
This reverts commit d9a9174fa5.
2019-09-04 11:37:19 -05:00
Alex Marginean
d9a9174fa5 drivers: net: driver for MDIO muxes controlled over I2C
This driver is used for MDIO muxes driven over I2C.  This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25 13:13:30 -05:00
Alex Marginean
1d99534bef drivers: net: add NXP ENETC MDIO driver
Adds a driver for the MDIO interface currently integrated in LS1028A SoC.
This MDIO interface is shared by multiple ethernet interfaces and is
presented as a stand-alone PCI function on the SoC ECAM.
Ethernet has a functional dependency on MDIO, for simplicity there is a
single config option for both.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25 13:13:30 -05:00
Alex Marginean
120b5ef287 drivers: net: add NXP ENETC ethernet driver
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A.  ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.

Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25 13:13:30 -05:00
Alex Marginean
c3d9f3f899 test: dm: add a test for MDIO MUX DM uclass
Adds a test using a makeshift MDIO MUX.  The test is based on the existing
MDIO test.  It uses the last emulated PHY register to verify MUX selection.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-18 16:37:13 -05:00
Alex Marginean
ec9594a50f test: dm: add MDIO test
A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15 13:32:25 -05:00
Shawn Guo
1d5b5d2f8f net: add higmacv300 Ethernet driver for HiSilicon platform
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200.  It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-23 17:57:24 -04:00
Horatiu Vultur
4c66157f42 net: mscc: Move ocelot_switch to mscc_eswitch folder
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01 14:13:36 +01:00
Gregory CLEMENT
c8546163fa net: add MSCC Ocelot switch support
This patch adds support for the Microsemi Ethernet switch present on
Ocelot SoCs.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-23 18:26:44 +01:00
Weijie Gao
23f17164d9 ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs
This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
2019-01-14 17:43:18 -05:00
Álvaro Fernández Rojas
9622972af4 net: add support for bcm6368-enet
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-12-19 15:23:01 +01:00
Álvaro Fernández Rojas
55e55fe4a6 net: add support for bcm6348-enet
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-12-19 15:23:00 +01:00
Grygorii Strashko
ffad5fa0cd driver: net: consolidate ti's code in separate folder
Add drivers/net/ti/ folder and move all TI's code in this folder for better
maintenance.

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2018-11-05 10:41:59 -06:00
Stefan Roese
c895ef4650 net: Add MT7628 ethernet driver
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs
(e.g. MT7628 and MT7688), including a minimum setup of the integrated
switch. This driver is loosly based on the driver version included in
this MediaTek github repository:

https://github.com/MediaTek-Labs/linkit-smart-uboot.git

Tested on the MT7688 LinkIt smart-gateway and on the
Gardena-smart-gateway.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Frank Wunderlich <frankwu@gmx.de>
Cc: Weijie Gao <hackpascal@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:56 -06:00
Marek Vasut
215a06565a net: designware: socfpga: Add Arria10 extras
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-08-13 22:35:42 +02:00
Joe Hershberger
f40a31e695 sandbox: eth-raw: Add a SIMPLE_BUS to enumerate host interfaces
Ask the OS for each of its interfaces and for each one, bind a U-Boot
device and then probe it. This will allocate the priv data structure
that is then populated.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-26 14:08:19 -05:00
Kunihiko Hayashi
a8927795ef net: add Socionext AVE ethernet driver support
Add driver for Socionext AVE ethernet controller that includes MAC and
MDIO bus supporting RGMII/RMII modes.
The driver behaves the ethernet driver model (DM_ETH) with devicetree.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13 13:54:17 -05:00
Tuomas Tynkkynen
ed9072c797 net: Drop CONFIG_TSI108_ETH
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-05-23 17:30:03 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tuomas Tynkkynen
d04791dfa5 net: Drop CONFIG_ENC28J60
Last user of this driver went away in October 2014 in
commit d58a9451e7 ("ppc/arm: zap EMK boards").

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:32 -05:00
Calvin Johnson
a802d1e268 configs: ls1012a: add pfe configuration for LS1012A
Add configurations for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22 15:05:31 -05:00
Michal Simek
744247de29 net: Remove Xilinx ll_temac driver
ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.

ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9ce)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-23 10:40:51 -05:00
Artturi Alm
e286fada9d sunxi: fix CONFIG_SUNXI_EMAC references
fixes CONFIG_SUNXI_EMAC references from drivers/net/Makefile and
include/configs/sunxi-common.h likely forgotten in:
	commit abc3e4df59 ("sunxi: Convert SUNXI_EMAC to Kconfig")

Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-09 14:39:09 +05:30
Christophe Leroy
fad51ac3af powerpc, 8xx: move FEC Ethernet driver in drivers/net
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08 15:56:02 -04:00
Heiko Schocher
98f705c9ce powerpc: remove 4xx support
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-07-03 17:35:28 -04:00
Heiko Schocher
064b55cfcb powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-06-16 10:14:55 -04:00
Marek Vasut
8ae51b6f32 net: ravb: Add Renesas Ethernet RAVB driver
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Based on work of:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
2017-05-22 04:38:24 +09:00