The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8,
4 is not valid. The seq number could be configured by alias node.
The following patch will use i2c4 as the begin for i.MX7ULP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Identify and distinguish between platform device type of MX7ULP
and LS1021A.
This is a fix to commit 7edf5c45("serial: lpuart: add i.MX7ULP
support").
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When we using network on board using sh-eth, it prints a lot of
"CACHE: Misaligned operation at range" messages.
This commit fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This changes Change structure used in sh_eth_read and sh_eth_write function
from struct sh_eth_dev to struct sh_eth_info. This is necessary to convert
to Driver Model.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
bd_t is not used in sh_eth_config(). This deletes bd_t from sh_eth_config()
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the chord style checked by checkpatch.pl.
Details of change details are as follows:
- Fix typo
Change from alligned to aligned.
- Remove whitespace before ','
- Add spaces preferred around that '|'
- Fix missing a blank line after declarations
- Remove space after a cast declaration
- Fix format of block comments
- Add a blank line after function/struct/union/enum declarations
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a b53_reg read/write command which allows inspecting the switch
registers. Because the Broadcom BCM53xx registers have different sizes,
we need to split the accesses in 8, 16, 32, 48 or 64 bits to obtain
expected results.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure that we pad small packets to a minimum length of 60 bytes
(without FCS). This is necessary to interface with Ethernet switches
that will reject RUNT frames unless padded correctly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.
This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This implementation manages several clocks, disable and
free all of them in case of error during probe and in remove
callback.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes a problem in the mvneta driver where if more than
one packet arrives between calls to mvneta_recv(), the additional
descriptors will be marked as free even though only one descriptor
has been read and processed from the receive queue. This causes
the additional packet(s) to be delayed until the next packet arrives.
>From this point on all packets will be delayed because the receive
queue will contain unprocessed packets but the hardware shows no
busy descriptors.
Signed-off-by: Jason Brown <jason.brown@apcon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the return value is a signed int, if the leading MSB of rdreg is a 1,
it will get signed extended and will return a negative value which is an
error even though we read the correct value.
Fixes: dfcc496ed7 ("net: mii: Changes not made by spatch")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
First, this table could never be included in the build anyway because
SH_ETH_TYPE_RZ is not defined until later in the file.
Second, the register PIR was missing, so PHY MDIO never worked.
Third, after adding the PIR register, the table is EXACTLY the same as
sh_eth_offset_gigabit, so there is no value to it.
Therefore, just delete it use the gigabit one.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The macros inl and outl maybe already be defined from file
arch/arm/include/asm/io.h so there may be no reason to define them.
And if you do try defined them here, you get a redefined complier warning.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit allows extended Marvell registers to be read with:
foo > mdio rx FEC 3.10
Reading from bus FEC
PHY at address 0:
3.16 - 0x1063
foo > mdio wx FEC 3.10 0x1011
The above code changes the way ETH connector LEDs blink.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.
This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.
This patch convert the return value to use error codes.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.
Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In order to discard this code when unused in SPL we need to guard the
command with a check for CONFIG_SPL_BUILD and we rearrange the code
slightly to make this cleaner.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
By default, the subordinate is set equally to the secondary bus (1) when
the RC boots, and does not alter afterwards.
This means that theoretically, the highest bus reachable downstream is
bus 1.
Force the PCIe RC subordinate to 0xff, otherwise no downstream
devices will be detected behind bus 1 if the booting OS does not allow
enumerating a higher busnr than the subordinate value of the primary
bus.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The QSPI module on i.MX7D is modified from i.MX6SX. The module used on
i.MX6UL/6ULL is reused from i.MX7D. They share same tx buffer size.
The endianness is not set at qspi driver initialization. So if we don't
boot from QSPI, we will get wrong endianness when accessing from AHB
address directly.
Add the compatible entry for 6ul/7d.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Before use GPIO, we need to request gpio first. Free gpio after use.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <ssbabic@denx.de>
On i.MX7ULP, the fuse words (except bank 0 and 1) only supports to
write once, because they use ECC mode. Multiple writes may damage
the ECC value and cause a wrong fuse value decoded when reading.
This patch adds a checking before the fuse word programming, only
can write when the word value is 0.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
struct mmc_data contains the block size to use for the data transfer.
Use this information instead of using the default value or the block length
information stored in struct mmc.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The SDcard initialization procedure does a few more things than it did earlier:
* switch the bus width even for 1-bit bus width
* check that speed has been properly set (in resp[4] of SD_CMD_SWITCH_FUNC)
Update the SD simulator to handle those requests gracefully.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Not using this function reduces the size of the binary. It's replaces by
a standard malloc() and the alignment requirement is handled by an
intermediate buffer on the stack.
Also make sure that the allocated buffer is freed in case of error.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
