Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes
And remove it from headers that end up redefining it.
Signed-off-by: Nishanth Menon <nm@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
All prerequisites are already available, so why not enable 8-bit
access - it is a matter of a define in the board file only.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Signed-off-by: Tom Rini <trini@ti.com>
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <trini@ti.com>
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Correct the console sys prompt to display the correct processor
and the corrent board
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2013-04-08 11:29:05 -04:00
Renamed from include/configs/omap5_evm.h (Browse further)
