Commit graph

16 commits

Author SHA1 Message Date
Patrick Delaunay
8d93a9755f ARM: dts: stm32m1: add reg for pll nodes
Fix the following DT dtc warnings for stm32mp1 boards:

Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0:
  node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1:
  node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2:
  node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3:
  node has a unit name, but no reg property

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13 17:26:23 +01:00
Antonio Borneo
db0cd2d3bc ARM: dts: stm32mp1: move FDCAN to PLL4_R
LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
cache the value at probe and pretend to use it later.

Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R.

Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13 17:26:22 +01:00
Patrick Delaunay
4d7d0e2e78 ARM: dts: stm32: update eMMC configuration for stm32mp157c-ev1
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1.
- update slew-rate for pin configuration
- update "vqmmc-supply"
- remove "st,sig-dir"
- add mandatory "pinctrl-names"
- add "mmc-ddr-3_3v"

This patch solve the eMMC detection issue for command "mmc dev 1".

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-11-26 10:11:48 +01:00
Patrick Delaunay
dd2810851e stm32mp1: board: support of error led on ed1/ev1 board
Create a function led_error_blink and add node in device
tree.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 11:19:23 +02:00
Patrick Delaunay
7acda7eae5 ARM: dts: stm32mp1: add pull-up on serial rx of console connected to STLINK
Avoid U-Boot auto-boot interruption for line break detection
on console when the RX line connected to STLINK is floating
(-IO error in getc cause by framing error and testc return 1)
Same workaround is applied on all the STMicroelectonics board.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27 09:36:56 +02:00
Patrick Delaunay
35a54d41d9 ARM: dts: stm32mp1: sync device tree with v5.2-rc4
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
2019-07-12 11:18:53 +02:00
Patrice Chotard
2366160eb2 ARM: dts: stm32: Synchronize DT with kernel one
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/

This patch adds initial support of STM32MP157 discovery boards:
  - Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
    This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
    and 512MB of DDR3. Several connections are available on this boards:
    4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...

  - Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
    This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
    and Murata wifi/BT combo is added.

Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12 16:09:13 +02:00
Patrick Delaunay
9a2ba2838b stm32mp1: support forced boot mode
The boot mode can be forced by key press
or by TAMP register, requested in kernel by syscon-reboot-mode

tamp: tamp@5c00a000 {
	compatible = "simple-bus", "syscon", "simple-mfd";
	reg = <0x5c00a000 0x400>;

	reboot-mode {
		compatible = "syscon-reboot-mode";
		offset = <0x150>; /* reg20 */
		mask = <0xff>;
		mode-normal = <0>;
		mode-fastboot = <0x1>;
		mode-recovery = <0x2>;
		mode-stm32cubeprogrammer = <0x3>;
		mode-ums_mmc0 = <0x10>;
		mode-ums_mmc1 = <0x11>;
		mode-ums_mmc2 = <0x12>;
	};
};

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Patrick Delaunay
e74b74c528 dts: stm32mp1: clock tree update
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
  - PLL3P set to 208.8MHz for MCU sub-system
  - PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
  - PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
  - PLL4P set to 99MHz for SDMMC and SPDIFRX
  - PLL4Q set to 74.25MHz for EVAL board

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09 07:50:57 -05:00
Patrick Delaunay
8e1665102f stm32mp1: add gpio led support
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-08-10 10:27:32 -04:00
Patrick Delaunay
8a07d5bfe1 stm32mp1: clock tree update
Configure clock tree for all the devices.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-07-20 15:55:06 -04:00
Patrick Delaunay
a674313c2c dts: import stm32mp1 device tree from linux kernel
This patch rebase the stm32mp1 device tree source from
linux kernel v4.18-rc1.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-07-20 15:55:05 -04:00
Tom Rini
4549e789c1 SPDX: Convert all of our multiple license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document.  Note that parenthesis are
allowed so when they were used before we continue to use them.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 10:24:31 -04:00
Patrick Delaunay
b90f0e7c37 stm32mp1: change STGEN clock source to HSE
No more use static frequency HSI = 64MHz for STGEN clock
but HSE (with higher accurency) by default.

Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency
is provided at boot by BootRom and cp15 cntfrq and modified
during clock tree initialization if needed.

When HSI is no more used by any device, this internal
oscillator can be switched off to reduce consumption.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06 20:45:28 -04:00
Patrick Delaunay
0ed232b153 stm32mp1: add eMMC support for ED1
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-04-06 20:45:28 -04:00
Patrick Delaunay
3d2d115a30 dts: add device tree for STM32MP157C-ED1 board
Add minimal devicetree for STM32MP157C-ED1 board,
with only the devices to allow boot from SDCARD:
- RCC for clock and reset
- UART4 for console
- I2C and PMIC
- DDR
- SDMMC0 for SDCard

Waiting Kernel upstream for alignment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-03-19 16:14:22 -04:00