Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a change similar to what is already in the Linux driver. We
should only program the CLRDATATOG bit when the current mode indicates
that it is needed.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
After gadget reinitializaton (after tftp has been done once)
packet_received may become equal to 1 due to nuking OUT_EP
while disabling it in eth_reset_config.
rx_submit called from usb_eth_init queues rx_req first time.
But the first call of usb_eth_recv from NetLoop queues rx_req
again due to packet_received = 1.
The following flow shows the path of functions calls when
this happens:
net/net.c:NetLoop
|
+-net/eth.c:eth_init
| ether.c:usb_eth_init
| |
| +-udc_driver:usb_gadget_handle_interrupts
| | udc_driver:...
| | ether.c:eth_setup
| | ether.c:eth_set_config
| | ether.c:eth_reset_config
| | udc_driver:usb_ep_disable
| | udc_driver:nuke
| | ether.c:rx_complete
| | ether.c: packet_received = 1;
| |
| +-ether.c:rx_submit
| udc_driver:usb_ep_queue --- The first time when rx_req is queued
|
+-net/eth.c:eth_rx
ether.c:usb_eth_recv
|
+-udc_driver:usb_gadget_handle_interrupts
| udc_driver:... --- no interrupts, returning
+-ether.c: if (packet_received) { ...
ether.c:rx_submit
udc_driver:usb_ep_queue --- The second time!
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Remove and fix needless and destructive operations with tx/rx_req.
1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Fixes most of checkpatch warnings and errors in USB gadget stack.
The most frequently encountered problems are:
1) "(foo*)", "foo * bar", "foo* bar"
2) C99 // comments
3) No spaces before/after/around '?', ':', '=', '==', ',', '&', '('
4) Spaces before '['
5) Spaces between function names and '('
6) Block braces in wrong places
7) Spaces before tabs
8) Macros with complex values not enclosed in parenthesis
9) Multiline comments start just after /*
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
The patch removes an endless loop in the usb_eth_send
if the tx_complete is not called before going
in the loop. The driver interrupt routine is called
allowing the driver to check if the TX is completed.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The buffer for the status request must be word aligned
because it is accessed with 32 bit pointer in the
eth_status_complete function.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch is based on commit bb9496c6f7e853e5d4edd5397c9d45f1968d623c
(done by Julia Lawall <julia@diku.dk>) from linux-2.6.git.
Since num is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fix potential oops on rare error path.
The patch is based on commit e7b13ec9235b9fded90f826ceeb8c34548631351
(done by David Brownell <david-b@pacbell.net>) from linux-2.6.git.
Description of the issue taken from linux kernel bugzilla:
(https://bugzilla.kernel.org/show_bug.cgi?id=9594)
The potential error can be tracked down as follows:
(1) line 807: let the second conjunct on the "if" statment be false
meaning "dev->status_ep" is null. This means the "if" evaluates
to false.
follow thru the code until...
(2) line 808: usb_ep_disable(dev->status_ep) passes in a null argument,
however "usb_ep_disable" cannot handle that:
(from include/linux/usb/gadget.h)
191 static inline int
192 usb_ep_disable (struct usb_ep *ep)
193 {
194 return ep->ops->disable (ep);
195 }
--
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Fix possible oops on stat_req->buf initialization and fix ep0 and
status_ep confusion (last one is just intended for stat_req keeping).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix in_ep and out_ep confusion (rx_req was allocated from out_ep, not
from in_ep) and add lost dev->req freeing.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Add lost 'qmult' definition for High Speed devices and make it
configurable through CONFIG_USB_ETH_QMULT.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Prohibit simultaneous usage of both old and new gadget stacks and
allow UDC drivers to be dependent on CONFIG_USB_ETHER.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
The MUSB_TXCSR_MODE register setting isn't supported on Blackfin musb
parts, so stub it out to 0. This matches Linux behavior.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin implementation of musb has a TXCOUNT register that needs to
be programmed when transmitting data.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
MUSB PHY on OMAP3EVM Rev >= E uses external Vbus supply to support
500mA of power.We need to program MUSB PHY to use external Vbus
for this purpose.
Adding 'extvbus' member in musb_config structure which should be set
by all the boards where MUSB interface is using external Vbus supply.
Also added ULPI bus control register read/write abstraction for
Blackfin processor as it doesn't have ULPI registers.
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Changed musb_config initialization for omap3.c, davinci.c
and da8xx.c using name of structure fields. This would cause
the uninitialized field to be null by default and thus would
help in avoiding to init some flags required to be set only
for a few selected platforms.
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add NEC EHCI controller to the list of the supported devices.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
drivers/usb/host/ehci-pci.c | 1 +
1 file changed, 1 insertion(+)
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
USB devices on the 2nd port are not detected and I get the following message:
The request port(1) is not configured
That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
The conversion from offsets to C structs lost a little padding in the DMA
register map. Accessing endpoints other than ep0 with DMA would fail as
the addresses wouldn't be adjusted correctly.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
SPEAr SoCs contain a synopsys usb device controller.
USB Device IP can work in 2 modes
- DMA mode
- Slave mode
The driver adds support only for slave mode operation of usb
device IP. This driver is used along with standard USBTTY
driver to obtain a tty interface over USB on the host
Signed-off-by: Vipin <vipin.kumar@st.com>
When referring to PCIe and USB 'endpoint' is the standard naming
convention.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
For MUSB devices that do not support multipoint (hubs), we have to emulate
a root hub so that we can support core operations like resetting ports.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
controller must terminate the reset and stabilize the state of the port within
2 milliseconds". Without termination, a port stays at reset state. This is
observed on ppc4xx(sequoia) boards.
Signed-off-by: Chris Zhang <chris@seamicro.com>
This patch fixes this warning during compile:
omap3.c: In function 'musb_platform_init':
omap3.c:126: warning: label 'end' defined but not used
Problem reported by: Dirk Behme[dirk.behme@googlemail.com]
Signed-off-by: Sanjeev Premi <premi@ti.com>
The RX Control/Status register has bits that we want to preserve, so don't
just write out a single bit. Preserve the others bits in the process.
The original code posted to the u-boot list had this behavior, but looks
like it was lost somewhere along the way to merging.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The multipoint handling under MUSB is optional, and some parts (like the
Blackfin processor) do not implement support for it.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The dynamic FIFO handling under MUSB is optional, and some parts (like
the Blackfin processor) do not implement support for it.
Due to this, the FIFO reading/writing steps need special handling, so
mark the common versions weak so drivers can override.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
OMAP3EVM uses ISP1504 phy and so twl4030 related init is not required.
Submitted-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This change adds the usb device support for musb.
Omap3 platform support added at the same level as davinci.
The interface for usbtty to use the musb device support was added.
Verified on omap3 beagle, zoom1 and zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The twl4030 provides a PHY device for connecting a link device,
like musb, to physical connection.
This change adds the twl4030 usb registers and functions for
initializing the PHY as required by omap3.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for
usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor
These are out right duplicates in usb.h
usb_device_descriptor
usb_string_descriptor
This one has extra unused elements
usb_endpoint_descriptor
unsigned char bRefresh
unsigned char bSynchAddress;
These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.
usb_config_descriptor
usb_interface_descriptor
The change is to consolidate the definition of the descriptors
to usbdescriptors.h. The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.
So
usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface
For these, the common descriptor elements are accessed now
by an element 'desc'.
As an example
- if (iface->bInterfaceClass != USB_CLASS_HUB)
+ if (iface->desc.bInterfaceClass != USB_CLASS_HUB)
This has been compile tested on MAKEALL arm, ppc and mips.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is cheked in Linux source and fix found to be in sync.
This patch is tested for USB host interface on Kirkwood based
Sheevaplug platform (ARM little endian board)
Risk: the impact of this patch is not validated on big endian board.
This need to be checked...
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
These functions are no longer defined, so remove their prototypes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
To prepare for the 85xx USB support, which requires interface enablement
only once in (specified) order, no different than instructions for
enabling the interface under 83xx. It is unknown why the original author
enabled the interface twice (checked for references in errata, etc).
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch corrects the missing PLLB initialization in usb_cpu_init()
for AT91SAM9261.
Because of the missing PLLB initialization, the USB support for all
AT91SAM9261 based boards will work only if the PLLB is configured by a
precedent bootloader.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This Patch adds Support for PXA27X UDC.
(Rebased to drivers/usb reorganisation)
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Fix the problem that cannot use external hub, because this driver
did not control correctly a DEVADDx register.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
At some point an intentional double space at the end of the sentence
got changed into a tab in the GPL header line:
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
This patch fixes the damage.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Somehow I missed the real driver part in my last patch version. This patch
now adds the driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds routines to handle (flush/invalidate) the dcache for the
QH and qTD structures and data buffers. This is needed on platforms using
this EHCI support with dcache enabled (like the MIPS VCT board port).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds the config option CONFIG_EHCI_HCD_INIT_AFTER_RESET
to call ehci_hcd_init() again after ehci_reset() is executed. This
is needed for the upcoming VCT EHCI support which needs to re-init
the hcd part again after the EHCI CMD_RESET is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes an issue that the speed of USB devices was not detected
correctly on some EHCI controllers. This will be used on the upcoming VCT
EHCI support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Adding DM6446 (TI DaVinci) platform specific USB functionality for
USB Phy and VBUS initialization.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Adding Mentor USB core functionality and Mentor USB Host controller
functionality for Mentor USB OTG controller (musbhdrc).
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Thomas Abraham <t-abraham@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Add USB ehci ixp4xx host controller. Test on ixdp465 board.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
USB ehci code cleanup. Use handshake instead of infinite while loop
to check the STD_ASS status
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Add USB ehci pci support. This patch doesn't include any
pci_ids and it is not tested on real hardware.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
- fix ehci_readl, ehci_writel
- introduce new define in ehci.h
- introduce the handshake function for waiting on a register
- fix usb_ehci_fsl with the new HC_LENGTH macro
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
IXP465 board and I find some errors in the code. This
patch fix:
- descriptor initizialization (config, interface and endpoint
must be one next-to the other when the USB_DT_CONFIG message
is send.
- FIX little/endian bigendian (introduce the CONFIG_EHCI_DESC_BIG_ENDIAN
and the CONFIG_EHCI_MMIO_BIG_ENDIAN)
- Introduce the linux version of the usb_config_descriptor and
usb_interface descriptor. This descriptor does't contains
u-boot extension.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
