This patch imports the Linux kernel warp7 dts as at upstream kernel commit
cf76c364a1e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once
corrected we can import the latest kernel DTS unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y
They are copied from Linux 4.20
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
At default, u-boot reserves the memory from SP - 4KB to DRAM end for
lmb in arch_lmb_reserve. So lmb won't allocate any memory from it.
But we found the 4K gap for SP is not enough now, because some FDT
updating operations are added in our u-boot before jumping to kernel,
which needs larger stack. This causes the lmb allocated memory is overwritten
by stack.
Fix the issue by implementing the board_lmb_reserve to reserve from
SP - 16KB to memory end for lmb.
Signed-off-by: Ye Li <ye.li@nxp.com>
Introduce u-boot dtsi for i.MX8QXP MEK board.
we do not introduce a common dtsi for SoC, because different board
has different requirement on which needs to be enabled in SPL DM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Like it was done on imx6 in commit 9236269de5 ("imx: mx6: Fix
implementantion reset_misc")
Do not call lcdif_power_down() in the SPL case to fix the following
build error:
LD spl/u-boot-spl
MKIMAGE u-boot.img
arch/arm/mach-imx/built-in.o: In function `reset_misc':
/home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down'
scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The following NXP application notes and manual recommend to ensure the
IVT DCD pointer is Null prior to calling HAB API authenticate_image()
function:
- AN12263: HABv4 RVT Guidelines and Recommendations
- AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using
HABv4
- CST docs: High Assurance Boot Version 4 Application Programming
Interface Reference Manual
Commit ca89df7dd4 ("imx: hab: Convert DCD non-NULL error to warning")
converted DCD non-NULL error to warning due to the lack of documentation
at the time of first patch submission. We have warned U-Boot users since
v2018.03, and it makes sense now to follow the NXP recommendation to
ensure the IVT DCD pointer is Null.
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error
if a DCD pointer is present in an image being authenticated by calling the
HAB RVT API. Older versions of HAB will process and run DCD if it is
present, and this could lead to an incorrect authentication boot flow.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Per Kever Yang, 32768 is a reasonable max size for TPL on RK3288.
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.
Allow these devices to set this from Kconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Add pinctrl node for TLMM and add mux request for uart node.
* Rename uart to the actual board uart port.
* Fix indentendation of sdhc2 node.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The TLMM_GPIO_ENABLE bit is actually use to disable
the GPIO. change it to TLMM_GPIO_DISABLE so it's clearer.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add pinctrl driver for Dragonboard820c, currently with only
one mux func to initialize pins for serial console.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The PLL for the UART was not set, and relied on previous
initializtion made by LK. add the appropriate initialization.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Deploy u-boot-spl.stm32 binary in u-boot root folder like
the rest of the boards.
This makes it more streamlined when building in Yocto, Buildroot etc..
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Most of the memory is being consumed by device binding code,
more space needed for other data structures.
Z-turn board has already hit the limit, others may follow soon.
Measuring only the memory consumed in device_bind_common, I've got
the following results (in decimal):
root_driver: 108
mod_exp_sw: 108
amba: 120
serial@e0000000 aka uart0: 112
serial@e0001000 aka uart1: 88
spi@e000d000 aka qspi: 120
sdhci@e0100000 aka mmc0: 455
sdhci@e0100000.blk: 208
slcr@f8000000: 96
clkc@100: 72
(total) 1487 = 0x5cf of 0x600
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from U-Boot leads to an immediate crash.
So let's make the same memory reservation as the vendor device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB
or 1 GiB.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
