- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Avoid concatenation with following message.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If a regulator does not support .set_suspend_enable or
.set_suspend_value then ret is set to ENOSYS early in the function.
The most serious impact of this is that when no automatic setting of
voltage is needed then the final regulator_set_enable() is skipped
because ret has not been cleared.
It seems that the error handling for regulator_set_suspend_value() is
also wrong as if this succeeds then the normal boot-on checks are still
required, and again ENOSYS needs special treatment here.
Fixes: 11406b8f7e ("dm: regulator: support regulator more state")
Signed-off-by: John Keeping <john@metanate.com>
Currently the 'sf update' command fails in case the 'start' offset is
not aligned to SPI NOR erase block size. Add the missing alignment
calculation. In case the start offset is in the middle of erase block,
round start address down to the nearest aligned one, compare only the
updated data between what is in the SPI NOR and what is being written,
copy new data at offset of the compare buffer, and write back the entire
erase block.
This is useful e.g. on i.MX6Q where the u-boot-with-spl.imx is at
offset 0x400 in the SPI NOR, while the SPI NOR may have erase block
size e.g. 0x1000 bytes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Enable boot/bootd command in toradex colibri-imx7 defconfig,
it's just convenient to have it in and every other toradex board
already includes it.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Multiple boards create duplicate entries in their respective
-u-boot.dtsi files which all basically do the same thing.
To consolidate these and make it easier to make improvements
going forward, consolidate them all into one place.
This file creates a flash.bin image using binman, and supports
LPDDR4, DDR4 and DDR3. Since individual boards use different
peripherals and different UART ports, those entries were kept
in their respective board files, but the spba1 node was addded
which contains all UART1-3 to help facilitate SPL_DM_SERIAL.
Individual users will still need to include their respective
UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file
which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is
enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Commit 290ffe5788 (imx8m: fix reading of DDR4 MR registers) lifted a
private definition of lpddr4_mr_read() from imx8mm-cl-iot-gate board
code to drivers/ddr/imx/imx8m/ddrphy_utils.c, because that version
actually seems to work in practice.
However, commit 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
reintroduced the broken version in drivers/ddr/imx/imx8m/ddr_init.c,
copied most of the rest of ddrphy_utils.c to
drivers/ddr/imx/phy/ddrphy_utils.c, and stopped building
drivers/ddr/imx/imx8m/ddrphy_utils.c [and that file was then finally
completely removed with 7e9bd84883 (imx8m: ddrphy_utils: Remove unused
file)].
I assume this must have broken the imx8mm-cl-iot-gate board, at least
those that have not had their eeprom programmed with the proper
information. It certainly did break our out-of-tree board which always
reads back the ID register and uses that for a sanity check.
So apply the fix from 290ffe5788 once again.
Fixes: 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
- enable bootcount command
- integrate bootcount using SNVS_LP general purpose register LPGPR0
- enable link-time optimisation
- explicitly set a boot delay of one second
- enable CRC32 and MD5
- enable command for low-level access to data in a partition
- enable time commands
- enable PMIC commands
- improve ETHPRIME configuration
- enable eMMC HS400 functionality
- enable fixed PHY and MDIO driver model
- remove stale PFUZE100 PMIC driver
- enable thermal management unit driver
- enable more USB host functionality
- enable hexdump
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update the distro config env memory layout for the Verdin iMX8M Mini and
Verdin iMX8M Plus again:
- loadaddr=0x48200000 allows for 128MB area for uncompressing (ie FIT
images, kernel_comp_addr_r, kernel_comp_size)
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Note that this corrects a pre-maturely applied version 2 of the same
patch set.
Fixes: bbe0089d29 ("verdin-imx8mm: verdin-imx8mp: update env memory layout")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP
devicetree file from linux-next tree.
commit <aec8ad34f7f24> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam devicetree file from linux-next tree.
commit <eefe06b295087> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus SoM)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The GW7903 has a BD71847 PMIC on I2C1. Adjust the model compare strings
to add it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Enable driver model for ulp watchdog timer. When CONFIG_WDT=y and the
status of device node is "okay", initr_watchdog will be called and
finally calls ulp_wdt_probe() and ulp_wdt_start().
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The reset source of the external PMIC on i.MX93 is WDOG_ANY PAD and the
source of WDOG_ANY PAD is interrupt. Therefore, using PMIC to reset
needs to enable the watchdog interrupt.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The WDOG clocks are sourced from the fixed 32KHz (lpo_clk).When the
timeout period exceeds 2 seconds, the value written to the TOVAL
register is larger than 16-bit can represent. Enabling watchdog
prescaler to solve this problem.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To use 32bits refresh and unlock command as default, check the CMD32EN
bit to select the corresponding commands.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
With the migration of the watchdog infrastructure to cyclic functions
it's been noticed, that at least one watchdog driver is broken now. As
the execution time of it's watchdog reset function is quite long.
In general it's not really necessary (right now) to disable the cyclic
function upon exceeding CPU time usage. So instead of disabling the
cylic function in this case, let's just print a warning once to show
this potential problem to the user.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Tom Rini <trini@konsulko.com>
Cc: Pali Rohár <pali@kernel.org>
In order to test that we properly handle watchdog(s) during the "wait
for the user to interrupt autoboot" phase, we need a watchdog device
to be watching us.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
