A new driver uclass is created to handle the reboot mode control.
The new uclass driver is updating an environment variable with the
configured reboot mode. The mode is extracted from a map provided
at initialization time. The map contains a list of modes
and associated ids.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_NET_MULTI has been removed long time ago by commit 795428fc67
("net: remove CONFIG_NET_MULTI") but 4 boards were added later which wasn't
found. The patch is removing this reference from 4 boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The macro should be passed a state, which should be passed
to the actual function. Otherwise using that macro would
yield a build error.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The ARM Juno boards can be used as somewhat decent machines to run
off-the-shelf distributions, with USB, SATA, GBit Ethernet and 8GB of
DRAM.
With stable DTs in the board's NOR flash this would work really nicely,
however the default boot command is to fetch a kernel and an initrd from
the on-board NOR flash, which sounds somewhat embedded.
Include the config_distro_bootcmd.h header and define the available
devices (starting with USB, to catch USB installer sticks) to make
distributions and UEFI work out of the box.
The NOR flash kernel functionality is still preserved as the last
resort, should all other methods fail.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The generic distro boot sequence iterates over several types of devices,
trying one after another. In doing do, it starts with setting the
"devtype" variable, then uses this later in more generic commands.
Now most (block) device types use a local variable for that, but DHCP
puts the type into the environment, where it shadows any local variables.
As a consequence any boot attempt after bootcmd_dhcp has been run fails:
===========================
VExpress64# run bootcmd_dhcp
...
VExpress64# run bootcmd_sata0
SATA#0:
(3.0 Gbps)
SATA#1:
(No RDY)
Device 0: Model: 16GB SATA Flash Drive ....
... is now current device
Couldn't find partition dhcp 0:1
===========================
This problem typically doesn't show, because DHCP is mostly the last
command to try, but is a problem when this order is different, or when
distro_bootcmd or bootcmd_xxx are run separately or multiple times.
Let bootcmd_dhcp use a local variable, as the other kids do, to make the
order of boot commands irrelevant, and allow repeated calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we build U-Boot with POSITION_INDEPENDENT we must have
SYS_TEXT_BASE be set to zero. Make this the default in that case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Switch to fit_image_get_data_and_size() for consistency with all other
data loaded from FIT.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As 'part_get_info_by_name' now returns more status codes than just
-1 to indicate failure, we need to update the return value check.
Signed-off-by: Anders Dellien <anders.dellien@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
This patch add support for using NXP's pca8574 I2C IO expander, which
has only 8 IO lines.
After this change the .data member's information from struct udevice_id
are used to either sent one or two bytes.
Moreover, the '_le16' suffix from pcf8575_i2c_{write|read}_le16()
functions have been removed as now we also sent 8 bit data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those members are not used anymore as ones from gpio_dev_priv
structure (when DM_GPIO support is enabled) are used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Allow pin name parameter for pimux staus command,
as gpio command to get status of one pin.
The possible usage of the command is:
> pinmux dev pinctrl
> pinmux status
> pinmux status -a
> pinmux status <pin-name>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the result of do_status and always returns a CMD_RET_ value
(-ENOSYS was a possible result of show_pinmux).
This patch also adds pincontrol name in error messages (dev->name)
and treats correctly the status sub command when pin-controller device is
not selected.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change ensures both U-Boot and OP-TEE see the same content
from shared memory when OP-TEE is invoked prior U-Boot relocation.
This change is required since U-Boot may execute with data cache off
while OP-TEE always enables cache on memory shared with U-Boot.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It's possible that LOAD_FIT_FULL will have different values for TPL and
SPL, in which case just checking CONFIG_SPL_LOAD_FIT_FULL causes this to
be compiled in to the TPL even though functions and struct members it
depends on are not.
Use CONFIG_IS_ENABLED() to ensure the correct TPL/SPL variant is
checked.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The result of dpio_close() is actually taken into account.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Change the reg variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a common empty ops: eqos_null_ops() to remove the duplicated empty
functions and reduce the driver size for stm32 and imx config.
This patch also aligns the prototype of ops 'eqos_stop_clks' with other
eqos ops by adding return value.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the generic ethernet phy which already manages the correct binding
for gpio reset, including the assert an deassert delays.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since the commit commit 6a895d039b ("net: Update eQos driver and FEC
driver to use eth phy interfaces") the field phyaddr of driver private data
struct eqos_priv is no more used in eqos_start() for the phy_connect()
parameter.
Now this variable is only initialized in eqos_probe_resources_stm32()
it can be removed.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Bind any subnode with name beginning by mdio, mdio0 for example,
and not only the "mdio" as namei of subnode.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace debug trace and printf to log macros:
- debug() replaced by dev_dbg() when device is available, this macro
indicate the device name since commit ceb70bb870 ("dm: Print device
name in dev_xxx like Linux")
- printf() replaced by log_notice() to allow dispatch to log backends.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The gpio reset and the assert or deassert delay are defined in generic
binding of the ethernet phy in Linux:
Documentation/devicetree/bindings/net/ethernet-phy.yaml
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
See also U-Boot: doc/device-tree-bindings/net/phy.txt
This patch adds the parsing of this common DT properties in the
u-class "eth_phy_generic", used by default in the associated driver
"eth_phy_generic_drv"
This parsing function eth_phy_of_to_plat can be reused by other
ethernet phy drivers for this uclass UCLASS_ETH_PHY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use same type as eth_device->iobase and support addresses greater
than INT_MAX.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmD41JkRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrea8+wgArpcRqyC2nCYtdDl1q/8mWQabct2rUJVt
rzIYzgyPgkRBLQjlE8xgEchzAPOuw0YzQnEz3T80wepBPIy53+QYXaqumd9iuhtm
B1x4r/GumqS4qgn9Pfqxabw2eP8DNbxClc14ExDx3zR1pUwp0DRvnYQV/w+W2RQp
nWFKDdhdnkxuXApiVc01RF/9I+IygstVl1TUklxlw9EGkdpirczIX5cP2lhW9rsV
Cm4fPz4V6AphiUQ4RpllossBNVHHlbVyKOtdGWe4CrERH8Zv8tIVRVeHCr0GydPr
ORhIZTk7hmwTav3Zi4XAQ434UZcRVrJFRkZvv8TpmMhMTVb8+gyZaQ==
=F/gP
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-21jul21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
dtoc improvements to show better warnings
minor test build fixes
sandbox fixes for SDL2 and running TPL
bloblist resize feature
binman multithreading
Fixed a defect of a null pointer being discovered by Coverity Scan:
CID 331544: Null pointer dereferences (REVERSE_INULL)
Null-checking "size" suggests that it may be null, but it has already been
dereferenced on all paths leading to the check.
Signed-off-by: Chen Guanqiao <chenguanqiao@kuaishou.com>
The sandbox can handle signals. Due to a damaged global data pointer
additional exceptions in the signal handler may occur leading to an endless
loop. In this case leave the handling of the secondary exception to the
operating system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
One of binman's attributes is that it is extremely fast, at least for a
Python program. Add some simple timing around operations that might take
a while, such as reading an image and compressing it. This should help
to maintain the performance as new features are added.
This is for debugging purposes only.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the process outputs a lot of data on stdout this can be quite slow,
since the bytestring is regenerated each time. Use a bytearray instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The constructor should not read the node information. Move it to the
ReadNode() method instead. This allows this etype to be subclassed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some images may take a while to build, e.g. if they are large and use slow
compression. Support compiling sections in parallel to speed things up.
Signed-off-by: Simon Glass <sjg@chromium.org>
(fixed to use a separate test file to fix flakiness)
At present compression uses the same temporary file for all invocations.
With multithreading this causes the data to become corrupted. Use a
different filename each time.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when function names are logged, the output is a little hard to
read since every function is a different length. Add a way to pad the
names so that the log messages line up vertically. This doesn't work if
the function name is very long, but it makes a big difference in most
cases.
Use 20 characters as a default since this covers the vast majority of
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to iterate over block devices. Typically there
are fixed and removable devices. For security reasons it is sometimes
useful to ignore removable devices since they are under user control.
Add iterators which support selecting the block-device type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for reading devicetree flags for MMC devices. With this we
can distinguish between fixed and removable drives. Note that this
information is only available when the device is probed, not when it is
bound, since it is read in the of_to_plat() method. This could be changed
if needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If SPL fails to boot, try to provide an error code to indicate what is
wrong. For example, if a uclass is missing, this can return -EPFNOSUPPORT
(-96) which provides useful information.
Add a helper for accessing the image-loader name so we can drop the use
of #ifdefs in this code.
Put this feature behind a CONFIG_SHOW_ERRORS option to avoid increasing
the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
If signature verification is not in use we don't need to worry about
the risk of using @ in node names. Update fit_image_verify() to allow
it if the function is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is possible to add a blob that ends at the end of the bloblist, but at
present this is not supported. Fix it and add a regression test for this
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some comments for struct bloblist_hdr are a bit ambiguous. Update them to
clarify the meaning more precisely. Also document bloblist_get_stats()
properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes a blob needs to expand, e.g. because it needs to hold more log
data. Add support for this. Note that the bloblist must have sufficient
spare space for this to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than calling directly into the sandbox SDL code, we can use the
normal U-Boot console handling for this feature. Update the code, to make
it more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
