This is a backport from Marvell U-Boot:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell
commit 381d029e7a ("fix: serdes: a38x, a39x: Improve USB3 electrical
configuration")
Improves electrical USB3 receiver jitter tolerance test:
- De-Emphasize force, in functional mode the transmitter should always
have 3.5db de-emphasize, so we are forcing it.
- After forcing De-Emphasize, choose 3.5db (After forcing, default is
6dB so need to change it to 3.5dB).
- Align90 set to 0x58 - this is the sample point in the receiver, after
the clock is recovered this sampler samples at the chosen value, usually
it is supposed to be 0x60(which is the center of the eye), but sometimes
after adding jitter and ISI the center of the eye can move slightly and
the sample point is not necessarily the exact center, and after
optimization (searching the middle of the eye manually) it was seen that
the center of the eye is actually 0x58 and not 0x60.
- FFE Res and FFE Cap set to 0xE & 0xF respectively: improves this
settings is adequate according to how the USB3 spec defines the
interconnect, thus improves USB3 jitter tolerance settings.
- Change the resolution of the DFE to 0x3 which is 6mV(highest
resolution) , this avoids the DFE to saturate and cease to work.
- HPF set to 0x3 which is 5Khz high pass filter, the function of the HPF
is to filter the low frequency patterns(below 5Khz) to make sure that
the signal is not a noise, the setting before was 0x1(205Khz), and the
change came since the USB3 CP0 pattern, that is used in the USB3 jitter
tolerance testing, is similar to PRBS15, which has 2^15=32768bits which
is 32768*200ps (200ps is one Unit interval in USB3(5Gbps)) = 6.5us,
which is in frequency terms: 152Khz. since the PRBS15 is a random
pattern and can theoretically have once in a while a pattern that will
be at frequency of 152Khz, hence the previous setting (205khz HPF) can
possibly filter this pattern which can cause to an error in the
receiver, thus this change to avoid such scenarios.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: René Straub <rene.straub@netmodule.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Config option ARMADA_39X is never set so remove all dead code hidden under
ifdef CONFIG_ARMADA_39X blocks.
Also remove useless checks for CONFIG_ARMADA_38X define as this macro is
always defined for a38x code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the RTC (Read Timing Control) values for PCIe memory wrappers
following an ERRATA (ERRATA# TDB). This means the PCIe accesses will
used slower memory Read Timing, to allow more efficient energy
consumption, in order to lower the minimum VDD of the memory. Will lead
to more robust memory when voltage drop occurs (VDDSEG)
The code is based on changes from Marvell's U-Boot, specifically:
20cd270407eb608a7c8dc4af19ae2b
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reduce Auto Voltage Scaling VDD limit when core frequency is lower than
1600MHz. This reduces core voltage level from 1.25V to 1.15V, which
saves power.
The code is taken from Marvell's U-Boot 2013.01 revision 18.06.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Marvell have release a B0 revision of the Armada-385 SoC. This fixes a
hardware errata enabling RGMII to work when the Ethernet voltage is
configured to 3.3V.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Some QCA988x based modules presence is not detected by the SERDES lanes,
so force this detection which will trigger the LTSSM state machine to
negotiate link.
An example of such a card is WLE900VX.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Move sys_env_device_rev_get() from the ddr training code to
sys_env_lib.c (which currently resides with the serdes code). This
brings sys_env_device_rev_get() into line with sys_env_device_id_get()
and sys_env_model_get().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
