The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
As the only pic32 platform does not enable flash, this is dead code.
Remove it.
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Upstream linux commit f7025a43a9da26.
The MTD subsystem has its own small museum of ancient NANDs in a form of
the CONFIG_MTD_NAND_MUSEUM_IDS configuration option. The museum contains
stone age NANDs with 256 bytes pages, as well as iron age NANDs with 512
bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig options and
already has too many of them, and there is a general kernel trend to
simplify the configuration menu.
We remove the stone age exhibits along with closing the museum
REMARK Don't apply this part from upstream:
Some of the iron age ones are transferred to the regular NAND depot.
Namely, only those which have unique device IDs are transferred, and the
ones which have conflicting device IDs are removed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit fb3bff5b407e58.
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 3b5206f4be9b65.
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 229204da53b31d.
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 10d4e75c36f6c1.
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 9b2d61f80b060c.
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 01389b6bd2f4f7.
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit c51d0ac59f2420.
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In preparation of moving specific nand support that are not jedec
or onfi
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
nand_get_flash_type was reworked in commit 1ca6f9483e. This change
break the Mediatek MT721. Fix it adjust the function call parameters
+include/linux/mtd/rawnand.h:32:62: note: expected 'struct nand_chip *' but argument is of type 'struct mtd_info *'
+ 32 | struct nand_flash_dev *nand_get_flash_type(struct nand_chip *chip,
+ | ~~~~~~~~~~~~~~~~~~^~~~
+drivers/mtd/nand/raw/mt7621_nand.c:1189:48: error: passing argument 2 of 'nand_get_flash_type' from incompatible pointer type [-Werror=incompatible-pointer-types]
+ | ^~~~
+ | |
+ | struct nand_chip *
+include/linux/mtd/rawnand.h:33:49: note: expected 'int *' but argument is of type 'struct nand_chip *'
+ 33 | int *maf_id, int *dev_id,
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
chip points to mtd. Passing chip is enough to have a reference
to mtd when is necessary
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit abbe26d144ec22.
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7f501f0a72036d.
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 29a198a1592d83.
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
To quote Andre:
One prominent feature is the restructering of the clock driver, which
allows to end up with one actual driver for all variants, although we
still only compile in support for one SoC.
Also contained are some initial SPI fixes, which should fix some
problems, and enable SPI flash support for the F1C100s SoC. Those
patches revealed more problems, I will queue fixes later on, but for
now it should at least still work.
Apart from some smaller fixes (for instance for NAND operation), there
is also preparation for the upcoming Allwinner D1 support, in form of
the USB PHY driver. There are more driver support patches to come.
The gitlab CI completed successfully, including the build test for all
160 sunxi boards. I also boot tested on a few boards, but didn't have
time for more elaborate tests this time.
There was no user of this callback after 5b66fdb29d anymore, and its
semantic as now inconsistent between stm and sst26. What we need for the
upcoming new usecase is a "completely unlocked" semantic. So consolidate
over this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Power-on-Reset is a method to restore flash back to 1S-1S-1S mode from 8D-8D-8D
in the begging of probe.
Command extension type is not standardized across flash vendors in DTR mode.
For suiting different vendor flash devices, adding a flag to seperate types for
soft reset on boot.
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Follow patch <f6adec1af4b2f5d3012480c6cdce7743b74a6156> (Allow using Micron mt35xu512aba
in Octal DTR mode).
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency for adding Macronix flash in Octal DTR mode.
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The sunxi nand SPL loader was broken at least for SUN4I,
SUN5I and SUN7I SOCs since the implementation change
from DMA to PIO usage - commit 6ddbb1e.
Root cause for this issue is the NFC control flag NFC_CTL_RAM_METHOD
being set by method nand_apply_config.
This flag controls the bus being used for the NFCs internal RAM access.
It must be set for the DMA use case only.
See A33_Nand_Flash_Controller_Specification.pdf page 12.
This fix is tested by myself on a Cubietruck A20 board.
Others should test it on new generation SOCs as well.
Signed-off-by: Markus Hoffrogge <mhoffrogge@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
The NAND flash controller of MT7621 supports only SLC NAND flashes.
It supports 4~12 bits correction with maximum 4KB page size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
With the current code if the board has an ONFI compliant NAND without
support to the get and set features, U-boot returns an ENOTSUP error when
trying to tune the timings which prevents the probe of the device.
Indeed onfi_set_features() return ENOTSUP error if set/get features is not
supported. In the case of timings we should not return ENOTSUP because we
can use the default timings. The NAND is already capable of listening at
its highest supported rate, so we assume in this case that it is fine to
skip the operation.
Fix it by adding an intermediate nand_onfi_set_timings() function which
does not error out if set/get feature is not supported.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SAMSUNG_ONENAND
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
ecc.mode is set to 0 (aliased to NAND_ECC_NONE) either when function
nand_scan_ident() has not selected ecc.mode or when it selected it to none
ecc mode.
Distinguish between these two states by checking of node property
"nand-ecc-mode" which function nand_scan_ident() uses for filling ecc.mode.
This change fixes usage of none ecc mode if it is specified in DTS file.
Fixes: c9ea9019c5 ("mtd: rawnand: fsl_elbc: Use ECC configuration from device tree")
Signed-off-by: Pali Rohár <pali@kernel.org>
mxs_nand_command() implementation assume that it's working with a
LP NAND, which is a common case nowadays and thus uses two bytes
for column address.
However this is wrong for NAND_CMD_READID and NAND_CMD_PARAM, which
expects only one byte of column address, even for LP NANDs.
This leads to ONFI detection problem with some NAND manufacturer (like
Winbond) but not with others (like Samsung and Spansion)
We fix this with a simple workaround to avoid the 2nd byte column address
for those two commands.
Also align the code with nand_base to support 16 bit devices.
Tested on an iMX6SX device with:
* Winbond W29N04GVSIAA
* Spansion S34ML04G100TF100
* Samsung K9F4G08U00
Tested on imx8mn device with:
* Windbond W29N04GV
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
CC: Stefano Babic <sbabic@denx.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
For proper DM support it is required to fill also mtd->dev member.
Otherwise DM would not see nand device at all.
Signed-off-by: Pali Rohár <pali@kernel.org>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set correct type for 3rd argument of ofnode_get_addr_size_index_notrans()
function. It expects fdt_size_t * and not fdt_addr_t *.
When these two types do not have same size then U-Boot throw compile
warning:
drivers/mtd/mtdpart.c: In function ‘add_mtd_partitions_of’:
drivers/mtd/mtdpart.c:906:57: warning: passing argument 3 of ‘ofnode_get_addr_size_index_notrans’ from incompatible pointer type [-Wincompatible-pointer-types]
offset = ofnode_get_addr_size_index_notrans(child, 0, &size);
^~~~~
In file included from include/dm/device.h:13,
from include/linux/mtd/mtd.h:26,
from include/ubi_uboot.h:28,
from drivers/mtd/mtdpart.c:27:
include/dm/ofnode.h:530:25: note: expected ‘fdt_size_t *’ {aka ‘long long unsigned int *’} but argument is of type ‘fdt_addr_t *’ {aka ‘long unsigned int *’}
fdt_size_t *size);
~~~~~~~~~~~~^~~~
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
