This patch adds driver support for the ASIX AX88179 USB3.0 to GbE network
adapter.
Driver has been tested on the RECS5250 COM module (similar to ARDALE5250).
Testcase was DHCP and PXE boot.
Signed-off-by: Rene Griessl <rgriessl@cit-ec.uni-bielefeld.de>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Repair the register configuration and add proper support for the
display attached to both LVDS channels.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Sequence like the following is completely useless and results from
an errorneous ordering of the statements during development. Zap it.
#ifdef FOO
#define FOO
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
This board uses setup_i2c() in SPL. The setup_i2c() function internally
calls gpio_request(), which in turn internally calls strdup(). The strdup()
requires a running mallocator, so this patch makes the mallocator available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Since the Riot & Mars boards are dev boards it's likely people will want to
run standard distros on them. So replace the current boot scripts with the
standard one from config_distro_bootcmd.h
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>
Update to use config_distro_defaults.h and remove explicit settings
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Tested-by: Nikolay Dimitrov <picmaster@mail.bg>
USB is a pretty common feature on exynos 5 board, so it seems sensible
to configure it directly from exynos5-common. As a side-effect this
makes USB available from u-boot on exynos 5420 based boards.
While there enable support for common USB ethernet cards to make it more
likely the default config allows booting for network and enable XHCI on
SMDK5420 which has it defined in the dts but not in its config.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The few Versatile Express ARMv8 platforms we have may just as
well be switched to generic board from the beginning.
Tested on the ARM foundation model and the in progress support
for the ARMv8 Juno board.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Add samsung,vbus-gpio information for the XU3. This allows the usage of
the EHCI controller on the XU3, which is connected to the SMSC LAN9514
chip (usb hub + network).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.
As a side-effect move the parade functions from the exynos system header
file to its own file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for Odroid-XU3.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The media for boot and environment is a board-specific feature, not a
processor-specific. This is same to console port number and some
other addresses. This patch moves the that kinds of configs to each
board-specific files from the common config file for Exynos5420.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The current current watchdog timeout of 12 seconds is a bit small for
booting into Linux, especially when using a NFS based rootfs. So lets
change this timeout to a more defensive value of 30 seconds.
Also we now call the hw_watchdog_init() function so that we override
the value already configured from the Preloader.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
There are two standard SD card slots on the Crown Bay board, which
are connected to the Topcliff PCH SDIO controllers. Enable the SDHC
support so that we can use them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We don't have driver for the Intel Topcliff PCH Gigabit Ethernet
controller for now, so enable the Intle E1000 NIC support, which
can be plugged into any PCIe slot on the Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some boards, most notably those with a PCIe ethernet NIC, require this
to avoid cache coherency problems. Since the option adds very little
code and overhead enable it across all Tegra generations. Other drivers
may also start supporting this functionality at some point, so enabling
it now will automatically reap the benefits later on.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Beaver has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network device driver so that the device can
boot over the network.
In addition the board has a mini-PCIe expansion slot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PCIe bus on Cardhu is routed to the dock connector. An ethernet NIC
is available on the dock over the PCIe bus. Enable the PCIe controller
and the network device driver so that the device can boot over the
network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra30 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra20 SoCs.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for the PCIe controller found on some generations of Tegra.
Tegra20 has 2 root ports with a total of 4 lanes, Tegra30 has 3 root
ports with a total of 6 lanes and Tegra124 has 2 root ports with a total
of 5 lanes.
This is based on the Linux kernel driver, originally submitted upstream
by Mike Rapoport.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The AS3722 provides a number of DC/DC converters and LDOs as well as 8
GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The normal image is working on DRAM. It is better to use DRAM also
for init stack than L2 cache.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Implement a feature to allow fastboot to write the downloaded image
to the space reserved for the Protective MBR and the Primary GUID
Partition Table.
Additionally, prepare and write the Backup GUID Partition Table.
Signed-off-by: Steve Rae <srae@broadcom.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[Test HW: Exynos4412 - Trats2]
In order to add detach functions for fastboot, make the DFU detach related
functions common so they can be shared.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[TestHW: Exynos4412-Trats2]
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Following boards has incorrect number of portals defined.
powerpc/T102xQDS
powerpc/T102xRDB
powerpc/T1040QDS
powerpc/T104xRDB
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following configs in header file:
CONFIG_SYS_GENERIC_BOARD
CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use asmlinkage defined in include/linux/linkage.h if necessary.
Actually no ARM board uses asmlinkage, so this commit has no impact.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Commit 65dd74a674 (x86: ivybridge: Implement SDRAM init) introduced
x86-specific asmlinkage into arch/x86/include/asm/config.h.
Commit ed0a2fbf14 (x86: Add a definition of asmlinkage) added the
same macro define again, this time, into include/common.h.
(Please do not add arch-specific stuff to include/common.h any more;
it is already too cluttered.)
The generic asmlinkage is defined in <linux/linkage.h>. If you want
to override it with an arch-specific one, the best way is to add it
to <asm/linkage.h> like Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enabled byte program support for sst flashes in sf.
Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.
A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Earlier commit 73a1cb27 mistakenly used CONFIG_SYS_TIMER_CLK_FREQ.
It should be CONFIG_TIMER_CLK_FREQ.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
[York Sun: This is the difference between two patch versions]
Reviewed-by: York Sun <yorksun@freescale.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
Sync this up with Linux v3.18-rc5. Exclude features that are unlikely to
supported in U-Boot soon (regulators, pinmux). Also the addresses are
updated to 32-bit. Otherwise it is the same. Also bring in the dt-bindings
for pinctrl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
There seem to be a few EEPROM drivers around - perhaps we should have a
single standard one? This simple driver is used for sandbox testing, but
could be pressed into more active service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enable the options to bring up I2C on sandbox. Also enable all the available
I2C commands for testing purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
In order to test I2C we need some sort of emulation interface. Add hooks
to allow a driver to emulate an I2C device for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The uclass implements the same operations as the current I2C framework but
makes some changes to make it fit driver model better:
- Remove the chip address from API calls
- Remove the address length from API calls
- Remove concept of 'current' I2C bus
- Drop all existing init functions
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The functions error's numbers are standarized - but the error
messages are not.
The errors are often handled with unclear error messages,
so why not use an errno standarized messages.
Advantages:
- This could decrease the binary size.
- Appended with a detailed information,
the error message will be clear.
This commit introduces new function:
- const char *errno_to_str(int errno)
The functions returns a pointer to the errno corresponding text message:
- if errno is null or positive number - a pointer to "Success" message
- if errno is negative - a pointer to errno related message
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Tom Rini <trini@ti.com>
Adjust the configuration to use the driver model version of the pl01x
serial driver. Add the required platform data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Move strlcpy() definition from drivers/usb/gadget/ether.c to
lib/string.c because it is a very useful function.
Let's add the prototype to include/linux/string.h too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For some SoCs, the system clock frequency may not equal to the
ARCH Timer's frequency.
This patch uses the CONFIG_TIMER_CLK_FREQ instead of
CONFIG_SYS_CLK_FREQ, then the system clock macro and arch timer
macor could be set separately and without interfering each other.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD/NAND/QSPI boot definations are wrong for QE support, this
patch is to fix this error.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch will fix the bug that the partitions on the SD card could
not be accessed and add the support for the FAT fs.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alt board has been connected to eMMC of 8GB to MMC port.
This enables MMC port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board has been connected to eMMC of 8GB to MMC1 port.
This enables MMC1 port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Board with R-Car SoC has USB and MMC. They might use the EXT2 or EXT4 file system.
This adds support ext2 and ext4 file system
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
