This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
The resets for the DSP processors on K3 SoCs are managed through the
Power and Sleep Controller (PSC) module. Each DSP typically has two
resets - a global module reset for powering on the device, and a local
reset that affects only the CPU while allowing access to the other
sub-modules within the DSP processor sub-systems.
The C66x DSPs have two levels of internal RAMs that can be used to
boot from, and the firmware loading into these RAMs require the
local reset to be asserted with the device powered on/enabled using
the module reset. Enhance the K3 DSP remoteproc driver to add support
for loading into the internal RAMs. The local reset is deasserted on
SoC power-on-reset, so logic has to be added in probe in remoteproc
mode to balance the remoteproc state-machine.
Note that the local resets are a no-op on C71x cores, and the hardware
does not supporting loading into its internal RAMs.
Signed-off-by: Suman Anna <s-anna@ti.com>
The DSP remote processors on K3 SoCs require a boot register to be
programmed with a boot address, and these boot addresses need to be
aligned on certain address boundaries. The current code does not have
any error checks, and relies on the System Firmware to perform the
checking. Add logic to perform this sanity check within the remoteproc
driver itself to detect these anomalies specifically, and print a
meaningful trace. This avoids the cumbersome debug of root-causing
such failures from the corresponding TI-SCI failure.
The C66x and C71x DSP cores have different alignment needs and are
as follows:
C66x DSP = 1 KB (0x400)
C71x DSP = 2 MB (0x200000)
Signed-off-by: Suman Anna <s-anna@ti.com>
The global module reset is deasserted through the ti_sci_power_domain_on()
call in k3_dsp_start(), but is not asserted back if the local module reset
fails. Fix this.
While at this, remove the stale comment about assigned-clock-rates that
seems to have been copied from the K3 ARM64 Remoteproc driver.
Fixes: ab827b3857 ("remoteproc: Introduce K3 C66 and C71 remoteproc driver")
Signed-off-by: Suman Anna <s-anna@ti.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Certain SoCs with K3 architecture have integrated a C66 Corepac DSP
subsystem and an advanced C71 DSPs. Introduce a remoteproc driver
that that does take care of loading an elf to any of the specified
DSPs and start it.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
