The macro called MUX_VAL generates a writel instruction with
semicolon at the end. This table was written to use semicolons,
however one was missed:
MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /* GPIO_4 */
Since the extra semicolon is unnecessary with the use of the macro,
remove all of them, and cleanup whitespace.
Reviewed-by: Wolfgang Denk <wd@denx.de>
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Adam Ford <aford173@gmail.com>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruhl7x RM, SSC is supported only for LCD
and MPU PLLs, but the PRCM_CM_SSC_DELTAMSTEP_DPLL_XXX and
PRCM_CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field
in the PRCM_CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE,
MPU, DDR, PER, DISP, EXTDEV).
Link: https://lore.kernel.org/r/20210606202253.31649-5-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Registers for adjusting the spread spectrum clocking (SSC) have been
added. As reported by the TI spruh73x RM, SSC is supported only for LCD
and MPU PLLs, but the CM_SSC_DELTAMSTEP_DPLL_XXX and
CM_SSC_MODFREQDIV_DPLL_XXX registers, as well as the enable field in the
CM_CLKMODE_DPLL_XXX registers are mapped for all PLLs (CORE, MPU, DDR,
PER, DISP).
Link: https://lore.kernel.org/r/20210606202253.31649-4-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
There are five omap3 based boards from LogicPD. Two of them
have added LTO support. Add the remaining three to use LTO.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This clarifies which callers must be updated to complete the DM_GPIO
conversion.
The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit enables the green status LED (PD18/GPIO 114) on boot in the
SPL, in order to provide visual feedback that the PinePhone is booting.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For some systems, such as the PinePhone, there is no way for the end
user to make sure the system is indeed booting before the boot script is
executed, which takes several seconds. Therefore, it can be useful to
provide early visual feedback as soon as possible.
In order achieve this goal, this patch initializes the status LED (if
configured) in the SPL.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The PineTab device-tree is already in u-boot, this commit adds the
corresponding defconfig, based on pinephone_defconfig.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move CONFIG_VIDEO_MXS from board headers to Kconfig
and drop it from obsolete cfb_console driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After DM_VIDEO conversion the 'vidconsole' is the correct name
for the frame buffer console. 'video' will not work, so update
the description of the config option.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present U-Boot has a header file called lz4.h for its own use. If the
host has its own lz4 header file installed (e.g. from the 'liblz4-dev'
package) then host builds will use that instead.
Move the U-Boot file into its own directory, as is done with various
other headers with the same problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert pixel values when necessary like we do for 16bpp
framebuffers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for 30bpp mode where pixels are picked in 32-bit
integers but use 10 bits instead of 8 bits for each component.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the FDT into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use boolean variables to deal with the strange #ifdef logic of this
function, so we can remove the #ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is far too long. Before trying to remove #ifdefs, split out
the code that deals with selecting the ramdisk into a separate function.
Leave the code indented as it was for easier review. The next patch cleans
this up along with checkpatch violations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place and does not need to use the
preprocessor. Move it to the C file and convert it to a normal function.
Drop fit_unsupported() since it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present EFI_SECURE BOOT selects RSA but does not necessarily enable
FIT_SIGNATURE. Mostly this is fine, but a few boards do not enable it,
so U-Boot tries to do RSA verification when loading FIT images, but it
is not enabled.
This worked because the condition for checking the RSA signature is
wrong in the fit_image_verify_with_data() function. In order to fix it
we need to fix this dependency. Make sure that FIT_SIGNATURE is enabled
so that RSA can be used.
It might be better to avoid using 'select' in this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use the new host_build() function for this, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This is not needed with Kconfig, since we can use IS_ENABLED() easily
enough and the board code is now in a separate file. Update the only place
where this is used and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for CRC32. With this we can use CONFIG_IS_ENABLED(CRC32)
directly in the host build, so drop the unnecessary indirection.
Add a few more conditions to SPL_CRC32 to avoid build failures as well as
TPL_CRC32. Also update hash.c to make crc32 optional and to actually take
notice of SPL_CRC32.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_RSASSA_PSS. With this we can use
CONFIG_IS_ENABLED(FIT_RSASSA_PSS) directly in the host build, so drop the
forcing of this in the image.h header.
Drop the #ifdef around padding_pss_verify() too since it is not needed.
Use the compiler to check the config where possible, instead of the
preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for FIT_VERBOSE. With this we can use
CONFIG_IS_ENABLED(FIT_VERBOSE) directly in the tools build, so drop the
forcing of this in the image.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Add a host Kconfig for OF_LIBFDT. With this we can use
CONFIG_IS_ENABLED(OF_LIBFDT) directly in the tools build, so drop the
unnecessary indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Make use of the host Kconfig for FIT. With this we can use
CONFIG_IS_ENABLED(FIT) directly in the host build, so drop the unnecessary
indirection.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We can use the __maybe_unused attribute to avoid some of the #ifdefs in
this file. Update the functions accordingly.
Note: The actual hashing interface is still a mess, with four separate
combinations and lots of #ifdefs. This should really use a driver
approach, e.g. as is done with partition drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
At present when building host tools, we force CONFIG_SHAxxx to be enabled
regardless of the board Kconfig setting. This is done in the image.h
header file.
For SPL we currently just assume the algorithm is desired if U-Boot proper
enables it.
Clean this up by adding new Kconfig options to enable hashing on the host,
relying on CONFIG_IS_ENABLED() to deal with the different builds.
Add new SPL Kconfigs for hardware-accelerated hashing, to maintain the
current settings.
This allows us to drop the image.h code and the I_WANT_MD5 hack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Unfortunately these were removed by mistake. This means that adding hash
support to SPL brings in all software algorithms, with a substantial
increase in code size.
The origin of the problem was renaming them to SPL_FIT_xxx and then these
were removed altogether in a later commit.
Add them back. This aligns with CONFIG_MD5, for example, which has an SPL
variant.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: f5bc9c25f3 ("image: Rename SPL_SHAxxx_SUPPORT to SPL_FIT_SHAxxx")
Fixes: eb5171ddec ("common: Remove unused CONFIG_FIT_SHAxxx selectors")
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
