Currently SPL binary is larger than 64kB, which is larger than
CONFIG_SPL_MAX_SIZE defined in imx7_spl.h.
This causes boot failure on the pico-mx7 targets.
Remove CONFIG_SPL_LIBDISK_SUPPORT option for now, so that the SPL
binary can fit into the 64kB range.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
This allow the addition of extra default configurations for each
baseboard, removing the boot menu when user boots for the first time.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the CAAM driver fails to be probed:
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
CAAM needs to be initialized in secure world, so enable
CONFIG_ARMV7_BOOT_SEC_DEFAULT to allow the driver to
probe successfully.
Tested with kernel mainline version 4.17.2.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx7d U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx7d to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the use of:
> run setup_emmc
inside of the U-Boot prompt to do the partitioning of the disk.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid`
environment helper to allow it to properly work with Yocto Project and
other distributions using extlinux autogenerated configuration files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
