Commit graph

2256 commits

Author SHA1 Message Date
Peng Fan
86ac7a9a5d imx: add i.MX8MQ EVK support
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.

The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC:  PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE:  Configureing TZASC380
NOTICE:  BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE:  BL31: Built : 09:28:54, Nov  8 2018
lpddr4 swffc start
NOTICE:  sip svc init

U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)

CPU:   Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM:  3 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot:  0
"

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2019-01-01 14:12:18 +01:00
Lukasz Majewski
0532014ae2 ARM: DTS: Provide pinfunc definitions for vybrid vf610 from Linux kernel
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-01 14:12:18 +01:00
Lukasz Majewski
3b13b68a49 ARM: DTS: Add iomux node to vf.dtsi for Vybrid devices
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-01-01 14:12:18 +01:00
Masahiro Yamada
2001a81cba ARM: uniphier: dts: sync with Linux 4.20
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:50:30 +09:00
Neil Armstrong
53904dc7c1 arm: dts: s400: Fix status for eMMC and SDIO ports
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
2018-12-19 16:20:50 +01:00
Tom Rini
d597b26d51 Improvements and fixes or u-boot-rockchip:
- new board: adds rv1108-elgin-r1 board support
 - rk3288-evb: dts: remove 'vmmc' from emmc node
 - rk3399-puma: dts: remove obsolete DTS node 'vcc5v0_host'
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcFpKgAAoJECaAFcEOcohNoPoIAIsUwrwTbaB6/fDaXBoVXPmf
 8IQx6TjFKhs5930civVjnNVBR/19swAVoR8dR6JSGHgjv9C1k6zjEZfcKyi8Gr4J
 NORaNklExXqyBfHr+htHDgJ1OjmAImbNaVhbkGFtD/gELQ9LI1eFfNIDv26ZxDYH
 WKV/EQNbOxyDeOShCxn4GzGjqG0h0mvm/PlFH2s59b5SLAM8Ptg6B7ZRoe+go5fz
 l7nBl/TBG99lJtMpECMIpl3rqpU/JfYy2ONYVerX0w4ZshWjWJg6/m4pwWwLlUNn
 eJR1VsC5DZ6ocfQinFPU9xvjxAYXEy42Li82hFQg9KKs+4uchbKCLYrAiEQd6nk=
 =8Rly
 -----END PGP SIGNATURE-----

Merge tag 'for-master-20181216' of git://git.denx.de/u-boot-rockchip

Improvements and fixes or u-boot-rockchip:
- new board: adds rv1108-elgin-r1 board support
- rk3288-evb: dts: remove 'vmmc' from emmc node
- rk3399-puma: dts: remove obsolete DTS node 'vcc5v0_host'
2018-12-16 20:49:46 -05:00
Otavio Salvador
e11ef3d26e ARM: rockchip: Add rv1108-elgin-r1 board support
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:

- UART
- eMMC
- USB

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-16 01:30:11 +01:00
Tom Rini
401c254044 Merge branch 'master' of git://git.denx.de/u-boot-usb
- Second half of the USB Gadget DM conversion
2018-12-15 17:49:57 -05:00
Kever Yang
9af1d5ef2f rockchip: rk3288-evb: dts: remove 'vmmc' from emmc node
This is a sync with kernel mainline dts.

The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-15 20:56:46 +01:00
Christoph Muellner
1ae5cd0226 rockchip: rk3399-puma: Remove obsolete DTS node 'vcc5v0_host'.
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).

An analysis of the situation shows, that both regulators
are actually describing the same supply.

This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.

Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-15 20:56:26 +01:00
Shawn Guo
655c6d997d poplar: fix boot failure caused by serial driver change
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.

  Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
  drivers that support both statically declared devices and
  configuration from device tree

Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver.  But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.

This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.

Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-12-15 11:49:56 -05:00
Jean-Jacques Hiblot
4ea0711104 dts: am4372: Enable USB1 in SPL
USB1 can be used by the romboot on all am4372 platforms to download a
firmware (SPL in our case).
It makes sense to enable USB1 in the SPL to download u-boot.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:10 +01:00
Jean-Jacques Hiblot
894f002f20 dts: Add a u-boot specific dtsi file for the am4372
This file is used to override the values found in am4372.dtsi
Use it to fix the "compatible" options for the controllers used
to support the USB (parent bus and syscons).

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Jean-Jacques Hiblot
d53653f3f9 ARM: dts: k2g-evm: enable USB0 and USB1
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Simon Glass
93a98a6ff3 dm: exynos: sound: Convert to use driver model
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.

Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-12-13 16:36:30 -07:00
Simon Glass
d6cadd5918 dm: sound: Add conversion to driver model
Move the existing hardware drivers over to use driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-12-13 16:36:29 -07:00
Simon Glass
51b06dc40b dm: sound: exynos: Correct codec bus addresses
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-12-13 16:32:49 -07:00
Simon Glass
c275a08bc4 snow: Expand U-Boot size
Now that we have EFI, etc. enabled, U-Boot is larger than it was. Expand
the region allocated for it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-12-13 16:32:49 -07:00
Tom Rini
d94604d558 Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEorkTmaQ1QAtDiYw67UVZlNoLnbQFAlwOzFoACgkQ7UVZlNoL
 nbQUdQ//SRRBfjUe8RYTbojvTGQav0GTxnMkz4GFSrqu0nvGMW2YSlheOMqq72sg
 rK5mQqDvdkItCn+G8AZ5NV2ijkQ7NQWCfqL3EtApzTpv6qjfgv7xvopz8q4NZvzB
 Wp+4cFf9YQjNwhJ7kLvWHB7SBiz9AfMYRAj9cscH9xsGL3HxPj62WDfwyK/QXana
 KIxRKQ26/1AdOZy272yv70vlFj4IwForxV3ACimsWRuYcb8yre3pE0tD7XpMCSNv
 9GOfL7r4LS7U0+QnJoVeYLMhttRvOGJNUYtO2+ImO5NC3u9v8ehYEQ3FjGmM69CB
 vuPDQBDQc+Ap+Iu3k18PYSstp+mc9fbe9SQdlx6ARAecQqWTN4EOhf8s3m2bQq3S
 B58I0Zvowcdm8V2JKdXw94UqZX862U8PWH0BmcuX+4k+kRDwwU4XQY2nLp+Htz1w
 2q6vEdKGj7YUOaomx9fmKRL+9BFGoD+M9mTiHOwzqwxy6Pa9VkruSvMErM7p2l/z
 xI/Q+xPJhyk5TXgZRsz4Nat59WpifWruibKEd4PArQ446heHWmzLWjw/MWiFyd/H
 agCdpDZVJ8R7h1Krs+Ez8XjR1Qcg0gs+CdNBuvqxzOpMQGGonXA1nwi8YfHykhII
 urfoC8pew1yxiLGw7J2JSX808HV/09WCSEsrOOhE3T78rXTDlS4=
 =aT7d
 -----END PGP SIGNATURE-----

Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq

Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC

[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-10 17:19:59 -05:00
Tom Rini
8bf3c2442b Improvements:
- init DRAM for RK322x in SPL
 - add FAN53555 PMIC/regulator driver
 - update MicroCrystal RV3029 driver to Kconfig and sync from Linux
 - add bootcount uclass and first DM-driver for bootcount
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
 Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
 VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
 9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
 A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
 jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
 =5sHL
 -----END PGP SIGNATURE-----

Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip

Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
2018-12-10 10:19:09 -05:00
Tom Rini
7ff485c68b Merge branch 'master' of git://git.denx.de/u-boot-i2c
- DM_I2C_COMPAT removal for all ti platforms from Jean-Jacques Hiblot
- Fix in i2c command help output from Chirstoph Muellner.
2018-12-10 07:16:33 -05:00
Tom Rini
48d299a799 Merge branch 'master' of git://git.denx.de/u-boot-usb
- DWC3 and UDC cleanup
2018-12-10 07:15:12 -05:00
Philipp Tomsich
eff43904b7 rockchip: rk3399-puma: enable fan53555 regulators in DTS
Now that we have FAN53555 support, we can enable the regulators in our
DTS.  To make these easier to identify on the U-Boot commandline, we
rename them to the names of the voltage rails they control.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-10 10:04:45 +01:00
Jean-Jacques Hiblot
69dab2be8e dts: am43x: omap5: Add node for I2C in SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:13:35 +01:00
Aditya Prayoga
5ca84c6dd2 arm: mvebu: helios4: Reset uSOM onboard phy during board init
Similar to Clearfog rev 2.1, GPIO 19 also used to reset onboard ethernet
PHY.

This patch depend on
net: mvneta: Add GPIO configuration support
[URL: https://patchwork.ozlabs.org/patch/1007736/]

Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-12-08 16:19:41 +01:00
Aditya Prayoga
8d7d97e2d1 arm: mvebu: helios4: Enable SPI flash support
Enable SPI flash support under U-Boot and SPL. The ENV size and offset,
ported from U-Boot 2013.01 Marvell version: 2015_T1.0p16

To create U-Boot image for SPI flash, user would need to replace
* CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC with CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
* CONFIG_ENV_IS_IN_MMC with CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-12-08 16:19:41 +01:00
Aditya Prayoga
c209a65e9e arm: mvebu: helios4: Enable I2C and IO Expander
Enable Marvell I2C driver and I2C IO expander. Set default bus to
external I2C bus. Define I2C aliases in device tree so it can be
recognized by the driver.

Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-12-08 16:19:41 +01:00
Jean-Jacques Hiblot
d0af9eb501 dts: dra7x: make ocp2scp@4a080000 compatible with simple-bus
This is required when DM_USB is used, to bind the USB phys.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-07 16:31:46 +01:00
Felix Brack
fdce9d35dc arm: dts: am33xx: Sync dts with Linux 4.20.0
This patch synchronizes the am33xx SoC specific files with those from
Linux 4.20.0. Hence all board maintainers of am33xx based boards are
on the cc list.
The main purpose of this patch is to prevent further diverging of the
dts files from U-Boot and those from Linux. It aims to set the stage
for the synchronization of board specific dts files. Example: I'm the
maintainer of the PDU001 board: once this patch is applied successfully
I will make changes to the board specific dts file in Linux only and
then post a patch with a copy of this exact dts file to U-Boot. This
will make U-Boot and Linux remain in sync.
The stumbling block of https://patchwork.ozlabs.org/patch/943627 was
removed by the patch https://patchwork.ozlabs.org/patch/962428 from
Lokesh Vutla (many thanks!). This omap-serial driver allows using the
Linux am33xx.dtsi file in U-Boot.
Other changes to dts and dtsi files made by this patch are mainly to
prevent _new_ warnings during the build process. Especially the warning
at pinmux@800 stating 'unnecessary #address-cells/#size-cells without
"ranges" or child "reg"' was not removed. This warning is a good example
showing the benefit of the synchronization: if it needs to be fixed it
will be fixed in Linux and ported back to U-Boot.
Buildman reports all 46 am33xx SoC based boards to build fine, with
warnings of course. Nevertheless this patch should be tested thoroughly
on as many boards as possible to prevent any collateral damage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-07 08:13:51 -05:00
Adam Ford
8a15bdb040 ARM: DTS: da850-evm: Re-sync da850-evm.dts from Linux 4.20
There has been some natural evolution of the device tree, so
resync with 4.20

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:50 -05:00
Adam Ford
ae67a9b330 ARM: dts: da850-lcdk: Sync from Linux 4.20
Re-synce the device tree files from Linux 4.20

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:50 -05:00
Adam Ford
031288abe9 ARM: DTS: da850: Sync from Linux 4.20
Re-sync with 4.20 due some some natural evolution.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:50 -05:00
Adam Ford
343b606261 ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit with Linux 4.20
Migrate some small device tree fixes from Linux 4.20.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:50 -05:00
Adam Ford
faef5b376e ARM: DTS: Resync LogicPD SOM-LV with Linux 4.20
There have been a few fixes to the device trees, so this
re-syncs the dts/dtsi files with Linux

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:49 -05:00
Adam Ford
5792f0d8be ARM: DTS: Resync am3517-evm.dts with Linux 4.20
The DTS file for the AM3517 had the incorrect CD polarity.  Resync with
the fixed DTS file from Linux.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-12-07 08:13:48 -05:00
Álvaro Fernández Rojas
e9e8d80d8c serial: bcm6858: remove driver and switch to bcm6345
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2018-12-07 08:13:46 -05:00
Felix Brack
2aadff0feb arm: am335x-pdu001: Enable CONFIG_BLK and CONFIG_DM_MMC
This patch enables CONFIG_BLK as well as CONFIG_DM_MMC for the PDU001
board. It depends on Patrice Chotard's patch 'power: regulator: denied
disable on always-on regulator' which prevents power cycling the vmmc
supply. Without this patch the board will not boot as vmmc is
unfortunately used by other board components, not just eMMC and micro SD
card. Furthermore my patch 'dts: am335x-pdu001: Fix polarity of card
detection input' is required to boot from external micro SD card. Without
this patch no SD card will be detected and hence booting will fail.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-07 08:13:46 -05:00
Felix Brack
ae0a157b38 dts: am335x-pdu001: Fix polarity of card detection input
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.

Signed-off-by: Felix Brack <fb@ltec.ch>
2018-12-07 08:13:45 -05:00
Benjamin Gaignard
075b0185b6 pinctrl: stm32: make pinctrl use hwspinlock
Protect configuration registers with a hardware spinlock.

If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-06 23:26:33 -05:00
Benjamin Gaignard
9119f547d3 hwspinlock: add stm32 hardware spinlock support
Implement hardware spinlock support for STM32MP1.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2018-12-06 23:26:33 -05:00
Priyanka Jain
4909b89ec7 armv8: lx2160a: Add LX2160A SoC Support
LX2160A Soc is based on Layerscape Chassis Generation 3.2
architecture with features:
 16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC,
 2 64-bit DDR4 memory controller, RGMII, 8 I2C controllers,
 3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs,
 4 TZASC instances, etc.

SoC personalites:
LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs
LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs

Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Peng Ma
8ec42856f1 armv8: dts: fsl-ls2080a: add sata node support
One ls2080a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Peng Ma
3e586ee307 armv8: dts: fsl-ls1088a: add sata node support
One ls1088a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Peng Ma
539e0cb6dc armv8: dts: fsl-ls1046a: add sata node support
One ls1046a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Manivannan Sadhasivam
467877341a rockchip: rk3399: Add Ficus EE board support
Add board support for Ficus EE board from Vamrs. This board utilizes
common Rock960 family support.

Following peripherals are tested and known to work:
* Gigabit Ethernet
* USB 2.0
* MMC

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[Reworked based on common Rock960 family support]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-06 16:04:49 +01:00
Manivannan Sadhasivam
07f7687869 rockchip: rk3399: Add Rock960 CE board support
Add board support for Rock960 CE board from Vamrs. This board utilizes
common Rock960 family support.

Following peripherals are tested and known to work:
* USB 2.0
* MMC

This commit also adds DDR configuration for LPDDR3-2GiB-1600MHz which
is being used on the board.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-06 16:04:49 +01:00
Manivannan Sadhasivam
1bad5e1492 rockchip: rk3399: Add common Rock960 family from Vamrs
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.

Below are some of the key differences between both Rock960 and Ficus
boards:

1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960

The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
2018-12-06 16:04:49 +01:00
Randy Li
2c9050cd3d arm: dts: rockchip: add some common pin-settings to rk3399
Those pins would be used by many boards.

Commit grabbed from Linux:

commit b41023282d07b61a53e2c9b9508912b1e7ce7b4f
Author: Randy Li <ayaka@soulik.info>
Date:   Thu Jun 21 21:32:10 2018 +0800

    arm64: dts: rockchip: add some common pin-settings to rk3399

    Those pins would be used by many boards.

    Signed-off-by: Randy Li <ayaka@soulik.info>
    Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-06 16:04:49 +01:00
Marek Vasut
cbff9f80ce ARM: dts: rmobile: Sync Gen3 DTs with Linux 4.19.6
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
3b255531b6 ARM: dts: rmobile: Sync Gen2 DTs with Linux 4.19.6
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
4e96b693ee ARM: dts: rmobile: Extract i2c6 on M2W Porter
The i2c6 node is missing in mainline Linux thus far, pull it
into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
47179e5737 ARM: dts: rmobile: Extract SCIF2 node on E3 Ebisu
The SCIF2 node is not in Linux 4.17 DTs on E3, pull it into U-Boot
specific DT extras until it hits mainline Linux, to make syncing of
DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
6bdb7a80cb ARM: dts: rmobile: Extract SDHI nodes on E3 Ebisu
The SDHI nodes are not in Linux 4.17 DTs in E3, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
1bce3ec801 ARM: dts: rmobile: Extract SDHI extras on H3, M3W, M3N Salvator-X
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
750a147b3c ARM: dts: rmobile: Extract SDHI extras on H3 and M3W ULCB
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
d2038b26e7 ARM: dts: rmobile: Extract CPLD node on H3 and M3W ULCB
The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the
node into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
1172ade967 ARM: dts: rmobile: Extract AVB node extras on V3M Eagle
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the
AVB node extras into U-Boot specific DT until they hit mainline Linux,
to make syncing of DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
830b94f768 ARM: dts: rmobile: Extract SDHI nodes on M3N
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
f529bc551b ARM: dts: rmobile: Extract USB nodes on M3N
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
8c7d9e1f62 ARM: dts: rmobile: Extract RPC node to u-boot specific DT
The RPC DT bindings are still work in progress. Extract the RPC DT node
from the DT to allow easier update and so it can be replaced once the DT
bindings are stable.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Marek Vasut
a89929bbb3 ARM: dts: rmobile: Add soc label to Gen3
Add label to the /soc node, so it can be referenced from the U-Boot DTs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
2018-12-04 09:21:07 +01:00
Tom Rini
0a3d59e010 Xilinx changes for v2019.01
microblaze:
 - Use default functions for memory decoding
 - Showing model from DT
 
 zynq:
 - Fix spi flash DTs
 - Fix zynq_help_text with CONFIG_SYS_LONGHELP
 - Tune cse/mini configurations
 - Enabling cse/mini testing with current targets
 
 zynqmp:
 - Enable gzip SPL support
 - Fix chip detection logic
 - Tune mini configurations
 - DT fixes(spi-flash, models, clocks, etc)
 - Add support for OF_SEPARATE configurations
 - Enabling mini testing with current targets
 - Add mini mtest configuration
 - Some minor config setting
 
 nand:
 - arasan: Add subpage configuration
 
 net:
 - gem: Add 64bit DMA support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlwFUAkACgkQykllyylKDCHtIACeO2G+jfSPxIjsyuPWbRup4e+A
 H5UAn3knKDNJ3VVidqO1C5o8Ye5JePZF
 =lW3g
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets

zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting

nand:
- arasan: Add subpage configuration

net:
- gem: Add 64bit DMA support
2018-12-03 19:30:54 -05:00
Tom Rini
ec0d0d8742 Merge branch 'master' of git://git.denx.de/u-boot-sh
- MMC fixes for R-Car Gen3
2018-12-03 17:51:45 -05:00
Yegor Yefremov
67c145a836 arm: baltos: move the board to CONFIG_BLK
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.

Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-12-03 10:44:10 -05:00
Loic Devulder
8973d81658 ARM: meson: Add regmap support for clock driver
This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.

DTS files are synchronized from Linux 4.19.

Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
2018-12-03 13:34:21 +01:00
Marek Vasut
0be621aebd ARM: dts: rmobile: Enable HS400 on Salvator-X, ULCB, Ebisu
Enable the HS400 support in DT on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03 12:51:17 +01:00
Marek Vasut
d0e0bbe7d1 ARM: dts: rmobile: Enable SDR modes on E3 Ebisu
Add regulators and pinmuxes for SDHI0 and SDHI1 SD and microSD
slots on E3 Ebisu and mark them as capable of up to SDR104 mode
of operation. With the SDHI fixes in place, it is now possible
to use SDR104.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03 12:51:17 +01:00
Marek Vasut
286ded3394 ARM: dts: rmobile: Enable SDR104 on Salvator-X and ULCB
Enable SDR104 modes on M3W and H3 boards. With the SDHI fixes
in place, it is now possible to use SDR104.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03 12:51:17 +01:00
Marek Vasut
ca3163ddb7 ARM: dts: rmobile: Add eMMC DS pinmux
Add pinmux entry for the eMMC DS line, as it is connected on these boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03 12:51:17 +01:00
Tom Rini
c1d6e0bbfd Improvements:
- RK3188 USB-UART functionality
 - errors triggering a hard-stop in SPL on the RK3399 are reported
 - Rockchip RV1108 (SoC) support
 - MicroCrystal RV3029 (RTC) DM driver
 
 Fixes:
 - RK3188 early UART setup
 - limit SD-card frequency to 40MHz on the RK3399-Q7
 - MIPI fixes
 - RK3399 CPUB clock initialisation
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJcAab4AAoJECaAFcEOcohNx8gH/0OuW443gsA8Ty0rXpCvbzSi
 UejfBfqljX4tYcUrgABVdMd2WdUyQ6rSoVgnX6mvfToCxd51L2CQiimrTJRQp/ZQ
 yCrwC8iFYwgmyM/0UnnjRa03WJvYBi3McWWIxQy7ZywQcZkdIuyn6t5AbcRppGMF
 67G0ft9KRwB+dMcgdRuikDThZRhAWZ30MdY4LFZvyGWupuv/mdpyYhjHYyv05CVf
 BvaUqRFkt86GBAW7Hq+OahH1t/xuZBcPJdt8GC40Blgfmle2uvZOIpoSEezVwFXm
 qKSj5FSSVQ9XtMeWwWvHLUxKSua0pIX5d7HmK9WqcsUIePDbzth8i+/BdA+5AD4=
 =EYJx
 -----END PGP SIGNATURE-----

Merge tag 'for-master-20181130' of git://git.denx.de/u-boot-rockchip

Improvements:
- RK3188 USB-UART functionality
- errors triggering a hard-stop in SPL on the RK3399 are reported
- Rockchip RV1108 (SoC) support
- MicroCrystal RV3029 (RTC) DM driver

Fixes:
- RK3188 early UART setup
- limit SD-card frequency to 40MHz on the RK3399-Q7
- MIPI fixes
- RK3399 CPUB clock initialisation
2018-12-01 14:17:27 -05:00
Otavio Salvador
8177c5c452 ARM: dts: rockchip: Add rv1108 USB OTG pinctrl
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-11-30 21:56:45 +01:00
Otavio Salvador
a8819e9a9e ARM: dts: rockchip: Add rv1108 eMMC pinctrl
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-11-30 21:56:44 +01:00
Philipp Tomsich
765246a18c rockchip: rk3399-puma: reduce sd card max-frequency to 40MHz
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.

Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).

Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
2018-11-30 21:56:44 +01:00
Tom Rini
d814ff34a1 Merge git://git.denx.de/u-boot-marvell
- Some Kirkwood boards converted to DM_SPI by Chris
- New Armada-385 SoC revision printed by Chris
- Ethernet enable on mcbin by Baruch
- Support 2 DRAM banks on Armada-8k boards by Baruch
2018-11-30 11:20:03 -05:00
Baruch Siach
eff26e4804 arm: mvebu: mcbin: dts: enable 1G network interface
Describe the 1Gb network interface with on-board 88E1512 PHY.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-30 10:58:10 +01:00
Michal Simek
ee97a9996a arm64: zynqmp: Add mini mtest configuration
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.

As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.

Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.

Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)

Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM:  WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level:       EL3
In:    dcc
Out:   dcc
Err:   dcc
ZynqMP>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-30 10:45:26 +01:00
Tom Rini
6d4a3ff264 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-11-29 16:36:53 -05:00
Tom Rini
93e72ac472 Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
 - net: designware: add meson meson compatibles
 - Amlogic Meson cleanup for AXG SoC support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJb/AwoAAoJEHfc29rIyEnR2dMQANCsuWQzKASCLgUzeL/KWhQ8
 gj1YEVGbS0meQ35hNo0hL6qfN4VkjazawyWnb40HVVADBjil42QuxN9rncovg69Q
 ZvPEo4XYNCkDzOU3UmoR2rjxxGICVFY6GCOuNbqzvB2x4gWJmoUeByqewKW2g2Zp
 jyjbzYvJ+r8wLtUFbdqaGvsHHC8hiIkjyeaqdXUc6NHJrGYasRuOsCO92bEioYC1
 XPh76c2ABAnbzJy7GArdlBbDOQrQxoEskVeP47ZjiPywXxGCkgHaRSXaUKzpz30G
 8MrA5AciL6pmurmsM0APlgvJwL7qaX1P6NxiJ+12prWWfAk1ZC2/MEKVZY+gO/CF
 vUAyzhus1oJ5JjccCngy/1ftkIReueSbUrzGYFvqhihs9g4QyRpi7F5MDKX0MvP2
 uk+XXStXs+rOZ2YdMFlV8l6G12TijcViZVmVHdh8qdl4t8WFlv7gENVUM+0mhyu2
 x5OsoYz5w2h9hCh/CB3oIZfyJBe5VZVHZ2fWIRZJ72J7toUGMewlKYQq2LOv7A9q
 w6vRGnza3fSPUZgYenznohaeo9vXG/WX7cNSPQiNBoiGeC+Y2ko5NHe2MIEnUD4c
 amp21KA6rWnWeHHvDbwo5DJ+NhCd6uMgkiZDLCuiTtns1/a03l0V6kgOvQLIBjhK
 KxBWBn6+rDPq1wJxhxab
 =Oo1g
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20181126' of git://git.denx.de/u-boot-amlogic

Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add meson meson compatibles
- Amlogic Meson cleanup for AXG SoC support
2018-11-29 15:16:58 -05:00
Simon Goldschmidt
e8dd60d489 arm: socfpga: make socfpga_socrates_defconfig boot from QSPI
This fixes the board's dts to supply SPL with QSPI info.

The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Simon Goldschmidt
c402e81702 dts: arm: socfpga: merge gen5 devicetrees from linux
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)

Adapt board dts files that are not in Linux to keep their old
behaviour.

Change licenses to SPDX.

(Patman warnings/errors are in 1:1 copied files from Linux)

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Simon Goldschmidt
2a3a99932b spi: cadence_qspi: use "cdns,qspi-nor" as compatible
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Michal Simek
6bd13ee94e arm64: zynqmp: Setup clock-output-names for si570 chips
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
8418d2deb8 arm64: zynqmp: Disable ltc2952 poweroff chip
This chip is on the board but handling should be done via firmware not
via Linux driver. Changing status property to keep it in the tree to
describe it instead of removing this node completely.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
d1fb3d024e arm64: zynqmp: Fix sdhci clock in emmc0 mini configuration
Add missing clocks property.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
0ed45f0025 arm64: zynqmp: Wire spi-flash compatible string with flashes
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Siva Durga Prasad Paladugu
9cd26aaf39 arm64: zynqmp: Define and enable qspi node for DC4 board
DC4 board has qspi on it hence define and enable
qspi node for it.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:29:58 +01:00
Ryder Lee
d84982dbfa arm: dts: MediaTek: add device tree for MT7623
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:50 -05:00
Ryder Lee
376ac00dc3 arm: dts: MediaTek: add device tree for MT7629
This patch adds MT7629 device tree and the includes it needs.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-28 23:04:49 -05:00
Marcin Niestroj
627d74c79b ARM: dts: am335x-chiliboard: add /chosen/stdout-path
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-26 22:52:13 -05:00
Marcin Niestroj
e067379f88 ARM: dts: am335x-chili*: add chiliSOM and chiliboard DTS files
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-26 22:52:13 -05:00
Neil Armstrong
78a08019cd ARM: dts: Sync Amlogic Meson AXG DT from Linux 4.20-rc1
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26 14:40:52 +01:00
Michal Simek
f3289d1f0e arm64: zynqmp: Reflect emmc controller ID in model in DT
Make sense to add controller ID to model name to have it visible through
the logs to know which controller is used by which configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-26 10:50:55 +01:00
Siva Durga Prasad Paladugu
c25e804dd8 arm: zynq: cse_qspi: Fix overwriting spi-rx-bus-width property
spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-26 10:50:54 +01:00
Rabeeh Khoury
5bbf36af7f ARM: mvebu: dts: add Clearfog GT-8K
The SolidRun Clearfog GT-8K is based on Armada 8040.

https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k

The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-20 13:08:44 +01:00
Lokesh Vutla
00b34e9937 armv7r: dts: am654: Add initial support
Add R5 specific dts for am654-evm.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-16 16:51:59 -05:00
Lokesh Vutla
2d0eba3a45 arm: dts: k3: Sync dts from Linux
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-16 16:51:59 -05:00
Adam Ford
c3b89468fc ARM: DTS: Resync am3517-evm.dts with Linux 4.19
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files.  This patch re-sync's the DTS and DTSI files with
Linux.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-11-16 13:34:37 -05:00
Philippe Reynes
786dc91492 bcm968580xref: add initial support
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.

This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-11-16 13:34:35 -05:00
Philippe Reynes
40b59b0586 bcm6858: add initial support
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-11-16 13:34:35 -05:00
Prasanthi Chellakumar
1473f6ac88 arm: at91: wdt: Convert watchdog driver to dm/dt
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.

Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
2018-11-16 13:34:34 -05:00
Tom Rini
6f44333018 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-11-14 18:25:34 -05:00
Tom Rini
208ecbad2e Merge branch 'next'
This brings in the u-boot-net PR from Joe.
2018-11-14 11:30:07 -05:00
Jagan Teki
e6b16e7852 board: allwinner: sun50i-h6: Add Orangepi Lite2 support
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13 22:13:09 +05:30
Jagan Teki
d45a07aaca arm64: allwinner: h6: Add common orangepi nodes into dtsi
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.

So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.

Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13 22:13:01 +05:30
Vasily Khoruzhick
b972831c3c sunxi: DT: add support for Pinebook
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:10:03 +05:30
Andre Przywara
4f9d34e633 sunxi: A64: Add Pine64-LTS board
The Pine64 LTS is an updated version of the Pine64, copying the
technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and
soldered SPI flash chip, even the broken SD card detect pin has been copied.
Consequently this leads to the .dts (copied from the kernel) just including
the SoPine baseboard .dts, and the defconfig being almost identical.
Nevertheless the boards deserves a separate config.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:06:08 +05:30
Andre Przywara
4c974eefbf sunxi: H3/H5: Update .dts files
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date:   Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:06:08 +05:30
Andre Przywara
ababb5920e sunxi: A64: Re-add syscon to DT node
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the
compatible name for the syscon controller, dropping the generic "syscon"
fallback. Using this new DT node will make the Ethernet driver in every
older kernel (or non-Linux kernels) fail to initialise the MAC device.

To allow booting distribution kernels (from installer images via UEFI,
for instance), re-add the syscon compatible string as a fallback. This
works with both older and newer kernels.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:06:08 +05:30
Andre Przywara
1b39a1834e sunxi: A64: Update .dts/.dtsi files
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date:   Wed Sep 26 19:48:24 2018 +0000
    arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:06:08 +05:30
Tom Rini
dd610e616c Fix coverity issues for i.MX8
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlvhbq0PHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et37tAL/2dPOxjQbhNfBKccpv0wGhxL66AykHX+CcMh
 RDTOfa6sVR0LwhtIxCT0RHHiq/RMglZXojTpUCUTB9QZ8UFHn+x01RM5H6MkG8oB
 a5HSD7aGeoutZ0Aqd/NYT/TSFMKNL4dQZaWYaq+nDlOW1rSlHlDJFQLcDcEK0Cz1
 RNOlgbiFT4R+6u2eECL48gHkpYMXBIAAalFMRyyNB8+XUJGeZdFQiAmroWCfXlUz
 MgCS1lMJh43+BuIpTfUr4Ca2FHJurZLouw0+YLFzONpTWn2qkWFGJSow982zayE7
 5tdiCPIgIDts+SVhN6dFojJauhYS032zWJY6siW8jmVSFzax+ib4WOmg0Ip8CAwH
 fd+6cSYMgqiW97HQcS/5f+/YcwC+mJG5kiP7lEMlkyB6Fj4vZ/HrHRaOTkdf1pDB
 S7mvGRWBl3eD8pxioblf9+vOmfVU/XT64SU9KhrCLAXs36U+Dmv2g2VEp4D1eDKc
 9W+8eofp86X3sKkxxPh42ngjV/WhOg==
 =GSUo
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20181106' of git://git.denx.de/u-boot-imx

Fix coverity issues for i.MX8
2018-11-06 11:12:00 -05:00
Stefan Roese
ae4c38a538 arm: mvebu: armada-xp-theadorable.dts: Change CS# for 2nd FPGA
The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.

Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-06 13:21:13 +01:00
Stefan Roese
6843db9922 arm: mvebu: armada-xp-theadorable.dts: Add "spi-flash" compatible property
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.

Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-06 13:21:13 +01:00
Fabio Estevam
78c640fed6 ARM: dts: fsl-imx8qxp-mek: Move regulator outside "simple-bus"
Commit 3c28576bb0 ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2018-11-06 11:25:55 +01:00
Cédric Le Goater
f55f565d71 aspeed: Activate ethernet devices on the ast2500 Eval Board
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Cédric Le Goater
6bdccc3025 aspeed: Update ast2500 SoC DTS file to Linux v4.17-rc6 level
This is a large update of the AST2500 SoC DTS file bringing it to the
level of commit 927c2fc2db19 :

    Author:  Joel Stanley <joel@jms.id.au>
    Date:    Sat Jun 2 01:18:53 2018 -0700

         ARM: dts: aspeed: Fix hwrng register address

There are some differences on the compatibility property names. scu,
reset and clock drivers are also different.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-11-05 10:41:58 -06:00
Jun Nie
7bb0d212f2 sunxi: add support for Banana Pi M2 Zero board
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-10-31 12:13:02 +05:30
Tom Rini
cf033e04da Merged imx8 architecture, fix build for imx8 + warnings
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlvRk0gPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3IuAL/0jfCqEIzKbPXIz81zJ+43ZNPsyu4LluUFsP
 2s5+yKN4zPnxDaHmVyxKynREqCNCcbfz7biStEPRzIjQYPBWUWrqz1yceqvOTqWQ
 eh51ItNeow28IlnVEr40e5cNL28KPsAdO8Tx6yNiXdPndPOgm3DuFlT+Xbnv2/+P
 X9GYBoCD7EQ3aUJBDUKcN/AFSAl8YCQ43FKhowM18/ExeURiKk8YDRXVFgTDDd4J
 HIlzUbyeIG24xfmxc0MsUMEufMjqQE7k/tMfFvQJiwLBLkzuO+1WmbPlWd7XHqco
 t68mheBcm8m2G/CZJoxCy8ymUi5PKDJBhw3qQz646h+JiXP1lg7Yw8hf4nREV56k
 v/bMiDU1exIflI9Qf8CibxRAYv3bjKJD6p/uua2CIvsLO4emLPbi7DHFBdaQq+WB
 r32O0Xc6LiRBIhr/qeL/5HmxFT2o4lo+O9ybo10uhK8RA1LTPlQ0UNMwmSPLl4zR
 7e5YwnRCcHV492+/Fn31LWXUUVVxVw==
 =kkpS
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imx

Merged imx8 architecture, fix build for imx8 + warnings
2018-10-25 10:16:21 -04:00
Peng Fan
3c28576bb0 arm: dts: imx8qxp: fix build warining
Fix below build warning.

arch/arm/dts/fsl-imx8qxp-mek.dtb: Warning (avoid_unnecessary_addr_size):
/regulators: unnecessary #address-cells/#size-cells without "ranges"
or child "reg" property

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-10-25 11:48:13 +02:00
Peng Fan
d0dd73974c imx: add i.MX8QXP MEK board support
Add i.MX8QXP MEK board support
Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver.
Added README file.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-10-22 13:00:09 +02:00
Peng Fan
f180f4a482 arm: dts: introduce dtsi for i.MX8QXP
Introduce dtsi for i.MX8QXP, since there is other variants i.MX8DX(P),
so add them there, because i.MX8QXP includes the dtsi of them.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-10-22 13:00:09 +02:00
Marek Vasut
4cc93fc281 ARM: dts: rmobile: Build -u-boot variants of DTs
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2018-10-18 20:38:27 +02:00
Hiroyuki Yokoyama
2a1eade825 ARM: dts: rmobile: r8a77990: Add USB2.0(EHCI) DT nodes on Ebisu
Add device tree nodes for USB2.0(EHCI) on R-Car E3 Ebisu board.

Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
2018-10-18 19:07:47 +02:00
Michal Simek
e7f327fe4d arm: zynq: Add efuse node for Zynq-7000S devices
Add access to efuse for Zynq-7000S device detection.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 14:58:45 +02:00
Michal Simek
6bfe3fffac arm: zynq: Add support for DLC20 board
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).

Boards have mix of Winbond/ST QSPIs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 14:58:45 +02:00
Tom Rini
98068b3be5 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-10-10 13:35:14 -04:00
Loic Devulder
2058b7395e ARM: meson: Add Khadas VIM2 board DT
This adds Device Tree for the Khadas VIM2 board.

The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
2018-10-10 13:32:40 -04:00
Patrice Chotard
1c547bf732 ARM: dts: stm32mp1: Add usbotg_hs regulator for stm32mp157c-ev1
Add usbotg_hs regulator to allow to use the USB mass-storage
feature on OTG usb port.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-10-10 13:32:40 -04:00
Sébastien Szymanski
2f90c62c8a ARM: opos6ul: make the board boot again
Commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot,
dm-spl") removes the u-boot,dm-spl properties from the imx6ul.dtsi file
and breaks the OPOS6UL board.
Add the u-boot,dm-spl properties into *-u-boot.dts files to make the
board boot again.

Fixes: commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-spl")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-10-09 18:36:03 +02:00
Marek Vasut
ae400fde75 ARM: dts: rmobile: Reinstate missing CPLD on ULCB
The CPLD is used to reset the ULCB and it was removed
during DT sync with Linux 4.17. Reinstate it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-10-09 17:21:44 +02:00
Jens Wiklander
7ab5630a42 arm: dt: hikey: Add optee node
Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2018-10-07 10:47:38 -04:00
Adam Ford
5ad4212ce0 ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV and OMAP35 Torpedo
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-06 14:09:27 -04:00
Adam Ford
e2e30f50a9 ARM: DTS: Add support for Logic PD OMAP35 Torpedo & SOM-LV
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences.  With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-06 09:04:18 -04:00
Adam Ford
c981cb8dda ARM: DTS: Remove unnecessary u-boot.dtsi options from omap3/36xx
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone.  This cleans up
this unnneeded stuff.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-06 09:04:18 -04:00
Adam Ford
87555d1415 ARM: DTS: LogicPD-SOM-LV & Torpedo: Resync DTS with Kernel
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-06 09:04:18 -04:00
Tom Rini
14573fb78f Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-10-05 21:17:35 -04:00
Marek Vasut
2da6d39e26 ARM: dts: rmobile: Reinstate missing i2c6 on Porter
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-10-03 12:56:12 +02:00
Heiko Stuebner
e4d5fa3db0 rockchip: rk3188: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.

The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.

[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02 09:35:39 +02:00
Heiko Stuebner
598a26a8fb rockchip: rk3188: add u-boot-specific mmc properties
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.

While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-10-02 09:35:19 +02:00
Ramon Fried
665e452515 dts: db410c: Add bindings for MSM USB phy
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30 13:00:36 -04:00
Ramon Fried
6b0861a942 dts: db410c: add alias for USB
Alias is required so req-seq will be filled.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30 13:00:35 -04:00
Tom Rini
cc49e2bdb8 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-09-29 11:48:02 -04:00
Tom Rini
27f622d568 Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
 Switch to driver model for SATA on LS1021A and LS1043A.
 Add support for LS1012AFRWY rev C board.
 Enable SMMU for LS1043A.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJbrkHRAAoJEO1FWZTaC520r3UQAIBntTglI1QK7YizVxZ1x9DL
 42oSEIwkuN0wbndR7Jzx4EPPFJ8yX4v3stoxC3qS5DQ9kHMzuqRQcIDYbcn5Qy7Z
 vd0mBUmpkRjr988pSaSHVQ8kPasncb545fCUumrXrCmhuG5Ea2Itw1zLdsTf7X5n
 39KxFUOAR63BDCT0ZlR4VyMo01GxxHWCzRQH/rOWVzOcJsWF7R52hWIBBzVDxKPv
 HF9SYaAB0PTFgSjJx5wYQ4xPdHVUp+svtYSJE8JYzEr/BvOVtL2iEi4t2rk19CrX
 IaVMFydlv2iDgWdoSZFCCN/6lGDWSv1LWPDglWhLQhOYvrJOjZfgzzeAGU7wqoz4
 JVjSLf6dHeOma55dbP/epDmyDFqWIfNOQ3uP4RM57xJ0PXQuT7ACVJctr6kHVTGL
 1ZZxPdKSSf9lvtzoogPTTYRD5Ry7ud3sYZ0v3OHN1sbVcaHaVoHPeXeSz1sLg3Q+
 zhUo1lXx4FcTz9R1fafdcqqAk/YGMZ7sBE+uYJPgExnApxrZID9IiOdGIBxo8jiK
 ozLmaCIDqRyu/qhQW9WMri1tvYdKwq/739gBvvcIcrLR5RzfNUdwWjhtBokPQQnS
 WZNqd3/0N8ZFGz7V0GOxCDnAo4nwQeZVFGMtTpoCtjPvr6DWBHsEUlQHTT3dQKz/
 TXygMYUYGA+/vux0Dt4I
 =XRFI
 -----END PGP SIGNATURE-----

Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq

Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
2018-09-29 11:47:32 -04:00
Adam Ford
96a82d33f8 ARM: DTS: various omap3: Remove cd-inverted from u-boot.dtsi
With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29 08:07:26 -04:00
Eugen Hristev
57fb8b4654 ARM: dts: at91: sama5d4_xplained: add onewire connector for LCD eeprom
Add onewire node in device tree for TM series LCDs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:44 -04:00
Eugen Hristev
db17fbfd96 ARM: dts: at91: sama5d2_ptc: add onewire connector for LCD eeprom
Add onewire node in device tree for TM series LCDs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:43 -04:00
Eugen Hristev
d656875372 ARM: dts: at91: sama5d27_som1_ek: add onewire connector for LCD eeprom
Add onewire node in device tree for TM series LCDs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:43 -04:00
Eugen Hristev
2b238c6cdb ARM: dts: at91: sama5d3_xplained: add onewire connector for LCD eeprom
Add onewire node in device tree for TM series LCDs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:43 -04:00
Eugen Hristev
7f0110d47e ARM: dts: at91: sama5d2_xplained: add onewire connector for LCD eeprom
Add onewire node in device tree for TM series LCDs

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:42 -04:00
Jagan Teki
9ad93c0c96 ARM: dts: sun8i: Update A23/A33/r16 dts(i) files from Linux-v4.18-rc3
Update all A23/A33/r16 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.

A23:
commit bc3bd041fe766219a44688b182c260064007f0cc
Author: Miquel Raynal <miquel.raynal@bootlin.com>
Date:   Tue Apr 24 17:55:02 2018 +0200

    ARM: dts: sun8i: a23/a33: declare NAND pins

A33:
commit 88fe315d2c0a397ef42d7639addab0e021ae911d
Author: Maxime Ripard <maxime.ripard@bootlin.com>
Date:   Wed Apr 4 11:57:15 2018 +0200

    ARM: dts: sun8i: a33: Add the DSI-related nodes

r16:
commit 9621d0bd1b0d61167e1853ac68cf4869c31bcc96
Author: Miquel Raynal <miquel.raynal@bootlin.com>
Date:   Tue Apr 24 17:55:03 2018 +0200

    ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support

Note:
- Drop pinctrl from sun8i-r16-nintendo-nes-classic-edition.dts since
  sun8i-a23-a33.dtsi is added with Linux sync.
- Don't sync non U-Boot supported dts files
   sun8i-a23-ippo-q8h-v1.2.dts
   sun8i-a23-ippo-q8h-v5.dts
   sun8i-a33-et-q8-v1.6.dts
   sun8i-a33-ippo-q8h-v1.2.dts
   sun8i-r16-nintendo-nes-classic.dts
   sun8i-r16-nintendo-super-nes-classic.dts

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28 22:09:24 +05:30
Jagan Teki
b9d59d08a6 ARM: dts: sun7i: Update A20 dts(i) files from Linux-v4.18-rc3
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date:   Wed May 16 14:38:08 2018 +0300

    ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board

Note:
- Update sun7i-a20-primo73.dts as per Linux, since
  this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
  added for this.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28 22:09:24 +05:30
Jagan Teki
d1d4295aab ARM: dts: sun6i: Update A31/A31s dts(i) files from Linux-v4.18-rc3
Update all A31/A31s devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit b240b419db5d624ce7a5a397d6f62a1a686009ec
Merge: 9c2dd8405c0c 518d2f43c358
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Thu Apr 5 21:18:09 2018 -0700

    Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28 22:09:24 +05:30
Jagan Teki
13b36face7 ARM: dts: sun5i: Update A10s/A13/gr8/r8 dts(i) files from Linux-v4.18-rc3
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date:   Tue Mar 27 14:58:00 2018 +0200

    Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28 22:09:24 +05:30
Jagan Teki
3c92cca3cd ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532
Author: Pascal Roeleven <dev@pascalroeleven.nl>
Date:   Fri Apr 20 12:21:12 2018 +0200

    ARM: dts: sun4i: Fix incorrect clocks for displays

Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts
like other dts file since there dts file are U-Boot specific.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-09-28 22:09:24 +05:30
Peng Ma
9ed5ec9b53 armv7: dts: fsl-ls1021a: add sata node support enable sata for ls1021a-qds and ls1021a-twr
Add sata node to support this feature.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:53:13 -07:00
Peng Ma
d92116566b armv8: dts: fsl-ls1043a: add sata node support
Add sata node to support ls1043a.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:52:11 -07:00
Yinbo Zhu
46d471f5b8 armv7: ls1021a: enable esdhc
This patch is to enable eSDHC for ls1021a.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:51:36 -07:00
Yinbo Zhu
2fd425f8e3 armv8: ls1046a: add eSDHC node
This patch is to add eSDHC node for ls1046a.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:51:22 -07:00
Yinbo Zhu
bdccf12839 armv8: ls1043a: add eSDHC node
This patch is to add eSDHC node for ls1043a.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:51:16 -07:00
Yinbo Zhu
585d357522 armv8: ls1088a: add eSDHC node
This patch is to add eSDHC node for ls1088a.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:51:11 -07:00
Yinbo Zhu
99e0071df5 armv8: ls2088a: add eSDHC node
This patch is to add eSDHC node for ls2088a.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27 08:50:39 -07:00
Patrice Chotard
bad48a4062 ARM: dts: stm32mp1: Add EHCI support for stm32mp157c-ev1 board
Add DT nodes to enable EHCI support

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-25 21:47:39 -04:00
Patrice Chotard
8e9c94d766 ARM: dts: stm32mp1: Add usb gadget support for stm32mp157c-ev1 board
Add DT nodes to enable DWC2 gadget support

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-25 21:47:39 -04:00
Marek Behún
863949e383 board: turris_mox: Fixup U-Boot's device tree if PCIe connected
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:39 +02:00
Baruch Siach
f26e379b31 dts: mvebu: mcbin: drop redundant SD slot node
Commit 61dccf73d3 (dts: mvebu: a80x0: Enable SD/eMMC interfaces) added
a redundant DT node for SD card slot. Drop it.

Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:38 +02:00
Marek Behún
0f6686e228 arch/arm/dts: Update Turris Mox device tree
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 09:00:38 +02:00
Adam Ford
abb205ded1 ARM: dts: da850-evm-u-boot: Remove redundant entries
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:38:08 -04:00
Adam Ford
8e12559193 arm: dts: da850: Re-sync da850-evm.dts from Linux 4.18
Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:38:04 -04:00
Tom Rini
d1e15041ab Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2018-09-11 08:50:10 -04:00
Lokesh Vutla
853f7f5018 arm64: dts: k3: Add u-boot specific nodes
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Lokesh Vutla
ea8ad1d9b6 arm64: dts: k3: Add Support for AM654 SoC
Add initial DT support for AM654 EVM that runs on A53.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-11 08:32:55 -04:00
Masahiro Yamada
c3ab1e118f mmc: uniphier-sd: sync with Linux
Sync with the driver code and the binding recently merged in Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:18 +09:00
Masahiro Yamada
33aae6b5ed ARM: dts: uniphier: sync DT with Linux 4.19-rc1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:16 +09:00
Eugen Hristev
51330c72f0 at91: fix devicetree warnings
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10 20:48:18 -04:00
Eugen Hristev
6e18adaf11 ARM: dts: Makefile: fix build for at91family
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10 20:48:18 -04:00
Adam Ford
548c35ff6e ARM: dts: logicpd-torpedo-37xx-devkit-u-boot: Fix MMC Card Detect
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.

Fixes: e6ea2390cd ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-05 16:01:22 -04:00
Tom Rini
b2f90c461e Merge branch 'master' of git://git.denx.de/u-boot-imx 2018-09-04 17:45:53 -04:00
Ye Li
25baafc44c dts: imx6ul_evk: Add DTS files for 14x14 EVK and 9x9 EVK boards
Add the board DTS files for 14x14 EVK and 9x9 EVK. They are necessary
for converting to use u-boot DM driver.

Two -u-boot.dtsi are added to modify compatible string of SPI flash
device to "spi-flash".

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
9e1e6f6fe8 dts: imx6ul: Update alias to support DM
Add spi0 alias for qspi for enabling DM SPI.
Change usb alias for usbotg1 and usbotg2 for enabling DM USB

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
3b82335015 imx: imx7d-sdb: Add DM QSPI support
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.

Other changes to support the DM QSPI:
 - Add QSPI node and alias spi0.
 - Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
   conflict
 - Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
   align with kernel and also present the conflict.
 - Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
   "spi-flash"
 - Remove iomux settings of qspi in board codes which is not needed
   for DM driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
0925ee2185 imx: imx6sx-sabreauto: convert to use DM QSPI driver
To support DM QSPI driver:
 - Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
   to "spi-flash" and add "num-cs" property.
 - Enable DM SPI and DM SPI FLASH configurations
 - Remove iomux settings of qspi1 in board codes which is not needed
   for DM driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Ye Li
536c5c7a33 imx: imx6sx-sdb: Enable DM QSPI driver
To support DM QSPI driver
 - Add spi0 and spi1 alias for qspi1 and qspi2.
 - Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
   to "spi-flash" and add "num-cs" property.
 - Enable DM SPI/QSPI relavent configurations
 - Remove iomux settings of qspi2 in board codes which is not needed
   for DM driver.
 - Add sf default settings. So running "sf probe" can detect the flash

Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04 08:47:23 +02:00
Kever Yang
feb64f9d51 rockchip: dts: fix unnecessary '-cells' warning
Fix warning below:
unnecessary #address-cells/#size-cells without "ranges" or child "reg"
property

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-08-29 20:44:50 +02:00
Marek Vasut
a029f540c5 ARM: dts: socfpga: Add missing NAND reset
The NAND reset is missing from DT, so the reset manager cannot unreset the NAND.
Add the missing DT reset entry.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:21 +02:00
Marek Vasut
b67f80148e ARM: dts: socfpga: Drop ad-hoc UART clock frequency encoding from DT
The UART clock frequency can be obtained from the clock framework by the
ns16550 driver, so drop this redundant DT node.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:21 +02:00
Marek Vasut
cca9af63a3 ARM: dts: socfpga: Flag timer clock as pre-reloc
Flag timer clock as DM pre-reloc, so that a timer driver can be used and
it can extract information about it's clock rate using the clock framework.
This patch also moves some of the pre-reloc flags into the core dtsi file,
this is because the timer is not board specific, but rather is used on all
boards.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-24 12:05:20 +02:00
Nicolas Chauvet
0de68cf3f8 arm: tegra: Restore host1x/dc dm-pre-reloc properties
Since commit f2faffecb0, tegra: Convert to use binman
the dm-pre-reloc properties are removed.

This leads U-Boot not to enable the display on paz00

This patch restore the dm-pre-reloc properties allowing
the bootloader to output to the display panel

v4: - Spell project name as appropriate
v3: - Fix few typos
v2: - Add more characters to commit hash

Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-08-21 08:34:55 -07:00
Tom Rini
b71d9e8b38 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-08-20 13:41:56 -04:00
Tom Rini
719afeb0b3 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2018-08-17 07:24:34 -04:00
Marek Vasut
ccc97432ad ARM: dts: socfpga: Add u-boot,dm-pre-reloc to necessary clock nodes
Add the pre-reloc DT markers to clock nodes needed in SPL and early
U-Boot stages. This is required to let the Arria10 clock driver start
early and provide clock information for UART and SDMMC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:42 +02:00
Marek Vasut
c29508045f ARM: dts: socfpga: Add i2c alias to A10 SoCDK
The A10 SoCDK is missing the I2C bus alias, so DM I2C cannot assign
the I2C bus a bus number. Add the missing alias.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:16 +02:00
Marek Vasut
3d8685f155 ARM: dts: socfpga: Add missing I2C resets
The I2Cx resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:16 +02:00
Marek Vasut
da61e50fc4 ARM: dts: socfpga: Fix Arria10 GMAC resets
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:16 +02:00
Marek Vasut
f5775e69cc ARM: dts: socfpga: Add missing UART resets
The UART0 and UART1 resets are missing from DT, so the reset manager
cannot control them. Add the missing DT reset entries.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:16 +02:00
Marek Vasut
6f96ed7e20 ARM: dts: socfpga: Flag reset manager on A10 as pre-reloc
The Altera reset manager block must be available very early on, since
it controls ie. UART resets. Flag it as pre-reloc.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
2018-08-13 22:35:16 +02:00
Simon Goldschmidt
79a436d568 arm: socfpga: fix device trees to work with DM serial
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-08-13 22:35:06 +02:00
Patrick Delaunay
2deaf5cc63 ARM: dts: stm32f4: Fix DT dtc warnings
This patch fix the following warnings for for stm32f429
evaluation and discovery boards:

unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-13 14:04:04 -04:00
Patrice Chotard
638ee5af6b ARM: dts: stm32mp157: Add ADC DT node
Add ADC device tree node. This allows to get analog conversions on
stm32mp157.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-13 14:04:04 -04:00
Patrice Chotard
6effb56fbc ARM: dts: stm32: remove cd-inverted for stm32f746-disco
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.

Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-13 14:04:04 -04:00
Patrice Chotard
4c55c83989 ARM: dts: stm32: remove cd-inverted for stm32f769-disco
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.

Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-13 14:04:04 -04:00
Jagan Teki
25b3d90b2c ARM: dts: sun8i: Update R40/V40 dts(i) files from Linux-v4.18-rc3
Update all R40/V40 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:

R40:
commit c36fd5a48bd20820855e3e91a89297eeaa31836e
Author: Chen-Yu Tsai <wens@csie.org>
Date:   Wed May 2 00:12:25 2018 +0800

    ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller

V40:
commit c5f0bb472795170ab5c33be12e29ce7465fb31ed
Author: Icenowy Zheng <icenowy@aosc.io>
Date:   Fri Apr 6 22:03:44 2018 +0800

    ARM: sun8i: v40: enable USB host ports for Banana Pi M2 Berry

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # BPI-M2-Ultra, BPI-M2-Berry
2018-08-13 13:10:09 +05:30
Jagan Teki
0ca4d40cfe ARM: dts: sun8i: Update A83T dts(i) files from Linux-v4.18-rc3
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date:   Fri May 4 21:05:44 2018 +0200

    ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC

Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-13 13:07:35 +05:30
Patrick Delaunay
8e1665102f stm32mp1: add gpio led support
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-08-10 10:27:32 -04:00
Tom Rini
fc82e7684b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2018-08-07 21:36:20 -04:00
Tom Rini
188ebc7b59 Xilinx fixes for v2018.09-rc2
xilinx:
 - Add support for zybo z7 and ultra96
 - Tune zynq and zynqmp mini configurations
 - Move SYS_MALLOC_LEN to Kconfig
 
 fdt
  - make static funcs
 
 gpio:
 - Fix soft gpio driver
 - Fix Zynq gpio driver by using platdata
 
 microblaze:
 - Fix Kconfig entry
 
 spi
 - Move ISSI to Kconfig
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAltpoBQACgkQykllyylKDCFiNwCfeyYIE1l99vfO9GVzmK3csc0w
 Yr4An20pvguAtvoWmqwh+WpBMiU/sqlh
 =9rRG
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.09-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx fixes for v2018.09-rc2

xilinx:
- Add support for zybo z7 and ultra96
- Tune zynq and zynqmp mini configurations
- Move SYS_MALLOC_LEN to Kconfig

fdt
 - make static funcs

gpio:
- Fix soft gpio driver
- Fix Zynq gpio driver by using platdata

microblaze:
- Fix Kconfig entry

spi
- Move ISSI to Kconfig
2018-08-07 11:32:50 -04:00
Luis Araneda
a492fdffa3 arm: zynq: dts: add spi flash node to zedboard
Add a flash node to fix the detection of the memory IC.
With the changes introduced with commit 8fee8845e7
("enf_sf: reuse setup_flash_device instead of open coding it")
the SPI speed is now read from device-tree or a default value
is applied. This replaced the old behavior of setting the
SPI speed to CONFIG_ENV_SPI_MAX_HZ.

As this board didn't have a flash node, the default value
was applied to the SPI speed, producing an error when probing
the flash memory (speed too slow).

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-07 11:03:43 +02:00
Chris Packham
a6477f7cbc ARM: kirkwood: add SBx81LIFXCAT board
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Jon Nettleton
14deee2081 arm: mvebu: clearfog: add u-boot, dm-spl tag for spi
This is required so SPL and u-boot can boot from spi
flash devices that use the dm drivers.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use -u-boot.dtsi]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Baruch Siach
69601ce003 arm: mvebu: helios4: remove duplicate sdhci pins node
The same pinctrl node appears in the solidrun-microsom dtsi. Use that
instead.

Cc: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Jon Nettleton
334eebefc2 arm: mvebu: Better align Clearfog dts file with Linux kernel
This makes changes so the u-boot dts file is structured more
similar to the mainline linux dtsi file.  It provides a minimal
common dts that can work for most boards based on the ClearFog
platform.  Ethernet support is only supported for eth0 however
all devices are left enabled so u-boot can generate and
provide mac addresses for all of the network interfaces.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on recent changes]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Baruch Siach
a4adb1f576 arm: mvebu: clearfog: use the microsom .dtsi
Use hardware description from the recently introduced microsom .dtsi
file to reduce duplication.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Baruch Siach
bf3eaa3e5c arm: mvebu: solidrun-microsom: update SPI flash compatible
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the SolidRun SOM.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-08-07 10:53:52 +02:00
Michal Simek
2570e12960 arm64: zynqmp: Add support for Avnet Ultra96
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Luis Araneda
58f449676a arm: zynq: add support for the zybo z7 board
The board is manufactured by Digilent
Main features:
- Soc: XC7Z010 (Z7-10) or XC7Z020 (Z7-20)
- RAM: 1 GB DDR3L
- FLASH: 16 MB QSPI
- 1 Gbps Ethernet
- USB 2.0
- microSD slot
- Pcam camera connector
- HDMI Tx and Rx
- Audio codec: stereo out, stereo in, mic
- 5 (Z7-10) or 6 (Z7-20) Pmod ports
- 6 push-buttons, 4 switches, 5 LEDs
- 1 (Z7-10) or 2 (Z7-20) RGB LEDs

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Michal Simek
df09969070 arm: zynq: Fix indentation for zynq-cse targets
Trivial DT style fixes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Michal Simek
7996fcca9d arm: zynq: Remove fclk-enable property for cse-nor target
Mini cse NOR configuration is running without PL that's why there is no
reason to enable clock to PL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Michal Simek
92226b5a6d arm: zynqmp: Fix sdhci clock in emmc1 mini configuration
Add missing clocks property with fix clock-names property to be aligned
with emmc0 configuration and binding doc.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06 08:44:35 +02:00
Minkyu Kang
972d8576d2 arm: spring: fix alias of mmc correctly
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-08-06 11:24:48 +09:00
Minkyu Kang
2f43135551 arm: exynos5: fix warning of dts
remove this warning: avoid_unnecessary_addr_size

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-08-06 11:24:45 +09:00
Minkyu Kang
8d93a31014 arm: exynos4: fix warning of dts
remove this warning: avoid_unnecessary_addr_size

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2018-08-06 11:24:42 +09:00
Tom Rini
0cba6e906a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-08-04 19:41:30 -04:00
Patrice Chotard
11c1b55827 ARM: dts: stm32: remove cd-inverted for stm32429i-eval
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.

Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-08-03 19:53:54 -04:00
Simon Glass
3ab9598df7 binman: Rename 'position' to 'offset'
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.

At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.

A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.

It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:

   tegra
   sunxi
   x86

The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-08-01 16:30:06 -06:00
Jagan Teki
89a897fc4d board: sun50i: h6: Add OrangePi One Plus initial support
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-07-31 20:50:01 +05:30
Icenowy Zheng
a8407b5642 sunxi: add support for Pine H64 board
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.

Add support for it.

The device tree is from Linux next-20180720.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
6f796a9bb4 sunxi: add support for Allwinner H6 SoC
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.

This patch adds support for it.

The corresponding DTSI file, from Linux next-20180720, is also
introduced.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Tom Rini
0e8a8a3110 Merge git://git.denx.de/u-boot-fsl-qoriq 2018-07-27 13:09:30 -04:00
Tom Warren
2eea126916 tegra: beaver/apalis: Fix DTC warning
Fix warning when compiling tegra30-beaver/-apalis.dts with latest DTC:

  "Warning (avoid_unnecessary_addr_size): /pci/pch@1f,0: unnecessary
   #address-cells/#size-cells without "ranges" or child "reg" property"

Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-07-26 13:15:31 -07:00
Yuantian Tang
86bff2bb09 armv8: dts: fsl-ls1012a: add sata node support
One ls1012a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-07-26 10:59:35 -07:00
Marek Vasut
64eeb15854 ARM: dts: socfpga: Adjust NAND register layout on Arria10
Adjust the NAND register size on Arria10 to reflect reality.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-25 00:13:32 +02:00
Adam Ford
d7cc15bb53 ARM: DTS: am3517-evm-u-boot: Mark MMC1 with cd-inverted
In order to use the device tree for MMC, the card-detect pin
needs to be inverted.  This patch places this into the
am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files
clean and in-sync with Linux

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
972edd4930 ARM: dts: am3517-evm-uboot: Add reg-shift for UART
With the resync of the omap3.dtsi file, the reg-shift was removed
so it breaks the UART.  Adding the reg-shift into the
am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps
the dts/dtsi files clean from Linux.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
5448ff33f2 ARM: DTS: Resync Logic PD SOM-LV 37xx devkit with Linux 4.18-RC4
There have been some significant changes to the DM37 SOM-LV device
tree.  This patch re-syncs it with Linux.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
e6ea2390cd ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit with Linux 4.18-RC4
There have been some refactoring of the DTS files for the Logic PD
DM37 Torpedo.  This patch re-sync's the DTS files with Linux

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
66dae3bbca ARM: dts: Resync OMAP3 and omap36xx with Linux 4.18-RC4
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux.  An addition include/dt-binding was
also brought with it.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
b8dbec5fb6 ARM: DTS: Resync am3517-evm.dts with Linux 4.18-rc4
Several changes have been made to the AM3517-evm and the underlying
am3517.dtsi file.  This patch re-sync's the DTS and DTSI files with
Linux.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Stefan Agner
31b1e17f44 board: toradex: add Colibri iMX6ULL support
Add support for the Colibri iMX6ULL module which comes with
on-board raw NAND.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23 10:12:00 +02:00
Stefan Agner
55f34f3a9e ARM: dts: imx6ull: use same compatible string as Linux is using
The GPMI NAND IP seems to be the same as used in i.MX 6Quad. Use
the fsl,imx6q-gpmi-nand compatible string like Linux devices trees
are.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-07-23 10:12:00 +02:00
Loic Devulder
77dd09211b ARM64: meson: Sync DT with Linux 4.17.5
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.5
(Linux commit 54fb3c180d05e9dfda892a93413514e99f0cbb19).

This will enable HDMI_5V for USB Amlogic Meson GXL P212 based boards.

Signed-off-by: Loic Devulder <ldevulder@suse.de>
2018-07-20 15:55:09 -04:00
Patrick Delaunay
8a07d5bfe1 stm32mp1: clock tree update
Configure clock tree for all the devices.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-07-20 15:55:06 -04:00
Patrick Delaunay
5f16f655cc stm32mp1: add support for stm32mp157c-ev1 board
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.

PS: CONFIG_PINCTRL_FULL activation avoid to increase
    SYS_MALLOC_F_LEN (Early malloc usage: 2034)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-07-20 15:55:05 -04:00
Patrick Delaunay
a674313c2c dts: import stm32mp1 device tree from linux kernel
This patch rebase the stm32mp1 device tree source from
linux kernel v4.18-rc1.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-07-20 15:55:05 -04:00
Hannes Schmelzer
fbc7c7decf board/BuR/brppt1: convert brppt1 boards to driver model
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2018-07-19 17:03:35 -04:00
Hannes Schmelzer
19aa4ac09d dts: am33xx: add u-boot, dm-spl to ocp bus
This is needed for having access to the devices below this bus, most
important is uart and boot-device (spi, mmc, ...) in SPL stage.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
2018-07-19 17:03:35 -04:00
Ramon Fried
6621bedb96 dts: db820c: added smem nodes
Added necessary nodes for Qualcomm smem driver.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 16:31:38 -04:00
Ramon Fried
072787ddd5 dts: db410c: added smem nodes
Added necessary nodes for Qualcomm smem driver.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 16:31:37 -04:00
Thomas McKahan
eee45b4f54 boards: amlogic: Add FriendlyElec NanoPi K2 board support
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.

This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller

Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-07-19 16:17:58 -04:00
Neil Armstrong
9c7ad1ed01 ARM: dts: sync meson-gxbb-nanopi-k2 from Linux 4.17
Get the meson-gxbb-nanopi-k2.dts file from Linux 4.17.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-07-19 16:17:58 -04:00
Siva Durga Prasad Paladugu
14ed50a4bf arm64: zynqmp: Add QSPI flash mini u-boot configuration
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Siva Durga Prasad Paladugu
1c310aec67 arm: zynq: Add parallel NOR flash mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Siva Durga Prasad Paladugu
6754fabe65 arm: zynq: Add Nand flash mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Michal Simek
c7e7948924 arm64: xilinx: Setup default number of chipselects for zcu100
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Tom Rini
1adbf2966a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-07-17 14:28:47 -04:00
Chen-Yu Tsai
32f67bb7a1 sunxi: Enable eMMC on Libre Computer Board ALL-H3-CC boards
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.

Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.

The device tree change was also submitted to the Linux Kernel and
has already been queued up for 4.19.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-17 21:07:34 +05:30
Siva Durga Prasad Paladugu
76338e2a0c zynqmp: zcu102: Add qspi driver support for ZynqMP zcu102 boards
This patch adds qspi driver support for all ZynqMP ZCU102
boards.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:03:10 +05:30
Lothar Felten
a8b36f22b2 configs: Bananapi_M2_Ultra: enable gigabit ethernet
Enable the gigabit ethernet for the Bananapi M2 Ultra board.
Tested on BananaPi M2 Berry (R40), custom board (V40)

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:29:02 +05:30
Lothar Felten
3c2abf5019 sunxi: R40: add gigabit ethernet devicetree node
Add a device tree node for the Allwinner R40/V40 GMAC gigabit
ethernet interface.
The R40 SoC does not use the syscon register for GMAC settings.
The gigabit ethernet interface can only be routed to a fixed set of
pins.
Updated to match the Linux kernel's device tree.

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:27:27 +05:30
Andre Przywara
df3ebdc99a sunxi: DT: A64: add proper SoPine baseboard device tree
When the defconfig for the SoPine baseboard was added, there wasn't any
proper DT for the board yet, so we used the Pine64 DT as a placeholder.
Copy the DT file(s) meanwhile added in Linux over to U-Boot, and use
them in our defconfig.
This is as of v4.18-rc3, exactly Linux commit:
commit 7d556bfc49adddf2beb0d16c91945c3b8b783282
Author: Jagan Teki <jagannadh.teki@gmail.com>
Date:   Mon Dec 4 10:23:07 2017 +0530

    arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:03:34 +05:30
Andre Przywara
2d0c3d6b16 sunxi: DT: H3: update board .dts files from Linux
Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Mon Jun 11 17:57:38 2018 -0700

    Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:03:16 +05:30
Andre Przywara
1caeae375f sunxi: DT: H5: update board .dts files from Linux
Update the .dts file for the various boards with an Allwinner H5 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit af5d05bdc99c211729cba0a3d5417bccfa308caf
Author: Neil Armstrong <narmstrong@baylibre.com>
Date:   Tue Apr 24 13:47:14 2018 +0200

    arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:03:05 +05:30
Andre Przywara
7514ed33d2 sunxi: DT: update device tree files for Allwinner H3 and H5 SoCs
Update the device tree files from the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit 55c5ba5e49a0a124ed416880e8227b493474495e
Author: Chen-Yu Tsai <wens@csie.org>
Date:   Tue Apr 24 19:34:22 2018 +0800

    arm64: dts: allwinner: h5: Add cpu0 label for first cpu

Since the H3 and H5 are very similar (aside from the actual ARM cores),
they share most the SoC .dtsi and thus have to be updated together.
One tiny change is the removal of the "arm/" prefix from the include
path in the sun50i-h5.dtsi, which is needed because we don't share the
same sophisticated DT directory layout of Linux.
Also we need to fix up the board .dts files already, since the .dtsi
removes some pins, so the .dts can't reference them anymore. This is to
maintain bisectability.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:02:54 +05:30
Andre Przywara
68dd17c302 sunxi: DT: A64: update board .dts files from Linux
Update the .dts files for the various boards with an Allwinner A64 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 818668055c9d588c9a9d151e3b258ed1adacba0b
Author: Jagan Teki <jagan@amarulasolutions.com>
Date:   Mon Apr 23 12:02:39 2018 +0530

    arm64: dts: allwinner: a64: bananapi-m64: add usb otg

It updates the existing DT files, adds the newly added axp803.dtsi and
removes our temporary kludge file to get Ethernet support in U-Boot.
I left the amarula-relic alone, as this DT has not reached mainline yet.
The changes are not critical anyway, and the next sync will fix this.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:02:41 +05:30
Andre Przywara
62f3c12c4d sunxi: DT: A64: update device tree file for Allwinner A64 SoC
Updates the device tree file from the the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit c1cff65f9b16b31e731e2e75bbe06638c86e1996
Author: Harald Geyer <harald@ccbib.org>
Date:   Thu Mar 15 16:25:08 2018 +0000

    arm64: dts: allwinner: a64: add simplefb for A64 SoC

This also pulls in the newly required include files for the clock and
reset bindings, also removes the now redundant part from our
*-u-boot.dtsi overlay file.
I kept the PWM node from U-Boot, as we recently gained this explicitly
for U-Boot's own usage and I don't want to regress here. This node is in
the queue for mainline Linux already, so the next sync will make it all
equal again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-16 12:01:58 +05:30
Ley Foon Tan
17b3f32dd0 arm: dts: socfpga: stratix10: Fix memory node
Commit 5dfd5607af2114047bd ("ARM: socfpga: Pull DRAM size from DT") get
memory size from DT. So, we need to update memory size in memory node.
Otherwise, it cause U-boot hang.

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 16:03:35 +02:00
Marek Vasut
df78f016e8 ARM: socfpga: Make DRAM node available in SPL
The SPL can also parse the DRAM configuration node to figure out the
memory layout, make sure it is available.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-12 09:22:13 +02:00
Manivannan Sadhasivam
ca769a1394 arm: dts: bubblegum_96: Enable UART5 for serial console
This commit enables UART5 found in S900 SoC for serial console support.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:37 -04:00
Manivannan Sadhasivam
2a8afb44ba arm: dts: s900: Add UART node
This commit adds UART node for Actions Semi S900 SoC.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:35 -04:00
Manivannan Sadhasivam
69e62417c7 arm: dts: s900: Add Clock Management Unit (CMU) nodes
This commit adds Clock Management Unit (CMU) nodes for Actions Semi
S900 SoC.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:28 -04:00
Manivannan Sadhasivam
eba6589f7e board: Add uCRobotics Bubblegum-96 board support
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.

Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons

U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:23 -04:00
Manivannan Sadhasivam
97775d26c2 arm: Add support for Actions Semi OWL SoC family
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2018-07-09 15:25:15 -04:00
Tom Rini
4ac5df4b41 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-07-03 23:09:34 -04:00
Tom Rini
03b54997d5 board/aries: Remove
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them.  Remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-02 15:52:50 -04:00
Tom Rini
de76610545 Merge git://git.denx.de/u-boot-imx 2018-06-27 13:09:55 -04:00
Jagan Teki
18053a8505 imx6ul: geam: Fix fdt_file mismatch
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)

So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.

This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-06-27 09:51:49 +02:00
Stefan Agner
fd8c1fc943 arm: dts: imx7: colibri: add raw NAND support
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-06-27 09:07:55 +02:00
Stefan Agner
aba6a0fb8f arm: dts: imx7: sync with Linux
Sync with Linux commit 60cc43fc8884 ("Linux 4.17-rc1").

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2018-06-27 09:07:55 +02:00
Masahiro Yamada
9ef88391d0 ARM: dts: uniphier: enable SD card for PXs3 reference board
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-06-23 01:28:17 +09:00
Masahiro Yamada
e885c5a602 ARM: dts: uniphier: sync DT with Linux 4.18-rc1
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-06-23 01:28:16 +09:00
Tom Rini
dc7df68f21 Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-06-21 09:02:35 -04:00
Ramon Fried
018e8637b8 configs: dragonboard410c: remove env partition offset
BOOT2 is not partitioned, no need for partition offset.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-06-19 07:31:46 -04:00
Marek Vasut
2c84d5218e ARM: dts: rmobile: Add HS200 support to E3 Ebisu
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-19 06:15:55 +02:00
Marek Vasut
ea273e8d72 ARM: dts: rmobile: Move the PHY reset GPIOs into PHY nodes
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-19 06:15:55 +02:00
Marek Vasut
24417edfff ARM: dts: rmobile: Move the PHY reset GPIO back
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-19 06:15:55 +02:00
Masahiro Yamada
28b538b69d .gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-06-18 14:43:12 -04:00
Ramon Fried
95a773005c db410c: fix alignment of dts file
Alignment was wrong, missing one tab. fix it.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-06-18 14:02:04 -04:00
Lukasz Majewski
0b35b2d117 board: Add support for KEY1 status detection on K+P's HSC|DDC boards
This code provides information if the K+P's imx53 boards had KEY1
pressed.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18 16:42:04 +02:00
Lukasz Majewski
642c1f519a board: imx53: Always disable display before starting kernel
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.

Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).

To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18 16:42:04 +02:00
Tom Rini
103c45fb0d Merge branch 'master' of git://git.denx.de/u-boot-sh 2018-06-17 09:09:40 -04:00
Hauke Mehrtens
76d69eb01d sun50i: h5: Add initial Orange Pi Zero Plus support
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.

H5 Orangepi Zero Plus has
 - Quad-core Cortex-A53
 - 512MB DDR3
 - micrSD slot
 - 16MBit SPI Nor flash
 - Debug TTL UART
 - 1GBit/s Ethernet (RTL8211E)
 - Wifi (RTL8189FTV)
 - USB 2.0 Host
 - USB 2.0 OTG + power supply

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Hauke Mehrtens
a6580dfd46 sun8i: h2: Add initial Orange Pi R1 support
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.

H2+ Orange Pi R1 has
 - Quad-core Cortex-A7
 - 256MB DDR3
 - micrSD slot
 - 128MBit SPI Nor flash
 - Debug TTL UART
 - 100MBit/s Ethernet (H2+)
 - 100MBit/s Ethernet (RTL8152B)
 - Wifi (RTL8189ETV)
 - USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Marek Vasut
6d82ed8d37 ARM: dts: rmobile: Add AVB PHY reset on V3M Eagle
Add EtherAVB PHY reset on V3M Eagle to let the AVB driver unreset the PHY.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 04:27:28 +02:00
Marek Vasut
29904b923e ARM: dts: rmobile: Add AVB pinmux on V3M Eagle
Add EtherAVB pinmux node on V3M Eagle to set the pinmux configuration.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 04:27:28 +02:00
Marek Vasut
bc19d28e6d ARM: dts: rmobile: Enable SDHI on E3 Ebisu
Enable SDHI on R8A77990 E3 Ebisu in DT.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 02:17:57 +02:00
Marek Vasut
ef6765ca62 ARM: dts: rmobile: Add initial SDHI nodes to R8A77990 E3
Add SDHI nodes to R8A77990 E3 SoC to allow SDHI operation.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 02:17:57 +02:00
Marek Vasut
65dcc809cd ARM: dts: rmobile: Add SCIF2 pinmux to E3 Ebisu
Add SCIF2 pinmux nodes to R8A77990 E3 Ebisu.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 02:17:57 +02:00
Marek Vasut
e183a6c7f2 ARM: dts: rmobile: Add Renesas RPC HF/QSPI DT node to R8A77990
Add device tree nodes for the Renesas RPC HF/QSPI controller
to R8A77990 E3.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-16 02:17:57 +02:00
Michal Simek
3c1eaec012 arm: zynq: Drop #address-cells and #size-cells from gpio-keys
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15 08:06:31 +02:00
Siva Durga Prasad Paladugu
bc0f4ed133 arm64: zynqmp: Split emmc configuration into emmc0 and emmc1
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15 08:06:31 +02:00
Marek Vasut
2519a293d5 ARM: rmobile: Sync Gen3 DTS with Linux v4.17
Sync the DTs with Linux v4.17.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-14 22:35:21 +02:00
Marek Vasut
252c8b45c9 ARM: rmobile: Sync Gen2 DTS with Linux v4.17
Sync the DTs with Linux v4.17.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-14 22:35:21 +02:00
Adam Ford
acaee30608 ARM: DTS: resync a3517.dtsi with Linux 4.17
Linux 4.17 was just released with some minor changes to the
am3517.dtsi.  This patch re-syncs the file.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13 07:49:14 -04:00