Commit graph

8 commits

Author SHA1 Message Date
Ioana Ciornei
74f04490f2 arm: dts: lx2160aqds: add nodes describing possible mezzanine cards
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.

This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
 * SD #1: 3, 7, 19, 20
 * SD #2: 11

Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.

Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19 09:22:07 +05:30
Ioana Ciornei
3695e4ccfd arm: dts: lx2160aqds: add MDIO slots
The LX2160A processor has two external MDIO interfaces, described in the
DTS as emdio1 and emdio2.

On the LX2160AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as eight input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.

Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 8 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.

Also, DPMAC 17 and 18 are updated to reference the on-board PHYs.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19 09:22:07 +05:30
Kuldeep Singh
bd294e43dc arm: dts: lx2160a: Use flexspi in octal I/O mode
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30 08:12:13 +05:30
Kuldeep Singh
4c1a52294f arm: dts: lx2160aqds: Add FSPI node properties
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.

Add fspi node properties aligned with LX2160A-RDB fspi properties.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30 08:12:13 +05:30
Chuanhua Han
07cb35fb71 armv8: dts: lx2160aqds : Add pcf2127 node
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:35 +05:30
Yinbo Zhu
85e5e21981 armv8: lx2160aqds: Enable eSDHC controllers
This patch is to enable esdhc controllers for lx2160aqds

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Peng Ma
d17eb57dcf armv8: lx2160aqds: Enable sata
Change sata node status to enable sata.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:56 +05:30
Pankaj Bansal
1eba723c72 lx2160aqds : Add support for LX2160AQDS platform
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:44 +05:30