Add information about memory usage when U-Boot is started from coreboot.
This is useful when debugging. Also, since coreboot takes a chunk of
memory in the middle of SDRAM for use by PCI devices, it can help avoid
overwriting this with a loaded kernel by accident.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use VENDOR_COREBOOT instead of TARGET_COREBOOT so we can have multiple
coreboot boards, sharing options. Only SYS_CONFIG_NAME needs to be
defined TARGET_COREBOOT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function comment for get_coreboot_info() and a declaration for
cb_get_sysinfo(), since this may be called from elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Set up coral so that it can boot from coreboot, even though it is a
bare-metal build. This helps with testing since the same image can be used
in both cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The BIOS version may not be present, e.g. on a Chrome OS build. Add the
BIOS date as well, so we get some sort of indication of coreboot's
vintage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A recent change to disable cache setup when booting from coreboot
assumed that this has been done by SPL. The result is that for the
coreboot board, the cache is disabled (in start.S) and never
re-enabled.
If the cache was turned off, as it is on boards without SPL, we should
turn it back on. Add this new condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These constants conflict with error codes returned by the MP
implementation when something is wrong. In particular, mp_first_cpu()
returns MP_SELECT_BSP when running without multiprocessing enabled.
Since this is -2, it is interpreted as an error by callers, which
expect a positive CPU number for the first CPU.
Correct this by using a different range for the pre-defined CPU
numbers, above zero and out of the range of possible CPU values. For
now it is safe to assume there are no more than 64K CPUs.
This fixes the 'mtrr' command when CONFIG_SMP is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When starting U-Boot from a previous-stage bootloader we presumably don't
need to set up the variable MTRRs. In fact this could be harmful if the
existing settings are not what U-Boot uses.
Skip that step in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These headers are not actually used. Drop them so that this driver can
be used by other boards, e.g. coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When booting from coreboot we may not have a PCH driver available. The
SPI driver can operate without the PCH but currently complains in this
case. Update it to continue to work normally. The only missing feature
is memory-mapping of SPI-flash contents, which is not essential.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions don't modify the device-ID struct that is passed in, so
mark the argument as const, so the data structure can be declared that
way. This allows it to be placed in the rodata section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This script was broken by the change to default archives for linking.
This is due to objcopy specifically disallowing copying of thin
archives. To fix this and re-support external users of this script,
switch to using the same logic the u-boot-initial-env make target uses
to dump the section from the object file.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Fixes: 958f2e57ef ("build: use thin archives instead of incremental linking")
Signed-off-by: Tom Rini <trini@konsulko.com>
When building the envtools target with CONFIG_USE_DEFAULT_ENV_FILE=y,
the tools require generated/defaultenv_autogenerated.h.
In file included from tools/env/fw_env.c:126:
include/env_default.h:115:10: fatal error: generated/defaultenv_autogenerated.h: No such file or directory
115 | #include "generated/defaultenv_autogenerated.h"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Joel Stanley <joel@jms.id.au>
Align Kconfig and Kbuild logic to Linux 4.20 release with minimal impact
on files outside of this scope.
Our previous Kconfig sync was done by commit 587e4a4296 ("kconfig /
kbuild: Re-sync with Linux 4.19").
As part of this re-sync, a few related changes from previous Linux
releases were found to have been missed and merged in, and are not in
the following list.
The imported Linux commits are:
[From prior to v4.19]
b1e0d8b70fa3 kbuild: Fix gcc -x syntax
a4353898980c kconfig: add CC_IS_GCC and GCC_VERSION
469cb7376c06 kconfig: add CC_IS_CLANG and CLANG_VERSION
[From v4.19 to v4.20]
487c7c7702ab kbuild: prefix Makefile.dtbinst path with $(srctree) unconditionally
0d91bf584fe5 kbuild: remove old check for CFLAGS use
25815cf5ffec kbuild: hide most of targets when running config or mixed targets
00d78ab2ba75 kbuild: remove dead code in cmd_files calculation in top Makefile
23066c3f4e21 Compiler Attributes: enable -Wstringop-truncation on W=1 (gcc >= 8)
37c8a5fafa3b kbuild: consolidate Devicetree dtb build rules
80463f1b7bf9 kbuild: add --include-dir flag only for out-of-tree build
77ec0c20c7e0 kbuild: remove VERSION and PATCHLEVEL from $(objtree)/Makefile
74bc0c09b2da kbuild: remove user ID check in scripts/mkmakefile
4fd61277f662 kbuild: do not pass $(objtree) to scripts/mkmakefile
80d0dda3a4e5 kbuild: simplify command line creation in scripts/mkmakefile
fb073a4b473e kbuild: add -Wno-pointer-sign flag unconditionally
9df3e7a7d7d6 kbuild: add -Wno-unused-but-set-variable flag unconditionally
69ea912fda74 kbuild: remove unneeded link_multi_deps
7d0ea2524202 kbuild: use 'else ifeq' for checksrc to improve readability
04c459d20448 kconfig: remove oldnoconfig target
0085b4191f3e kconfig: remove silentoldconfig target
3f80babd9ca4 kbuild: remove unused cc-fullversion variable
2cd3faf87d2d merge_config.sh: Allow to define config prefix
076f421da5d4 kbuild: replace cc-name test with CONFIG_CC_IS_CLANG
6bbe4385d035 kconfig: merge_config: avoid false positive matches from comment lines
[From post v4.20]
885480b08469 Makefile: Move -Wno-unused-but-set-variable out of GCC only block
There are a number of changes related to additional warnings as well as
being able to drop cc-name entirely that have been omitted for now as
additional work is required first.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Update U-Boot's version of scripts/get_maintainer.pl to sync it up with the
latest changes to the Linux kernel's version of the same script.
The last sync was with Linux kernel version v4.16. The commits to the kernel's
get_maintainer.pl since then (starting with the most recent) are:
6343f6b71f83 get_maintainer: exclude MAINTAINERS file(s) from --git-fallback
cdfe2d220476 get_maintainer: add test for file in VCS
e33c9fe8b80c get_maintainer: fix unexpected behavior for path/to//file (double slashes)
0c78c0137621 get_maintainer: add email addresses from .yaml files
0ef82fcefb99 scripts/get_maintainer.pl: deprioritize old Fixes: addresses
ef0c08192ac0 get_maintainer: remove uses of P: for maintainer name
2f5bd343694e scripts/get_maintainer.pl: add signatures from Fixes: <badcommit> lines in commit message
49662503e8e4 get_maintainer: add ability to skip moderated mailing lists
0fbd75fd7fee get_maintainer: allow option --mpath <directory> to read all files in <directory>
5f0baf95b1ed get_maintainer.pl: add -mpath=<path or file> for MAINTAINERS file location
31bb82c9caa9 get_maintainer: allow usage outside of kernel tree
0455c74788fd get_maintainer: improve patch recognition
882ea1d64eb3 scripts: use SPDX tag in get_maintainer and checkpatch
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Function rtc_to_tm() is needed for FAT file system support even if we don't
have a real time clock. So move it from drivers/ to lib/.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The return value '-ENOSPC' of fit_set_timestamp function does not match
the caller fit_image_write_sig's expection which is '-FDT_ERR_NOSPACE'.
Fix it by not calling fit_set_timestamp, but call fdt_setprop instead.
This fixes a following mkimage error:
| Can't write signature for 'signature@1' signature node in
| 'conf@imx6ull-colibri-wifi-eval-v3.dtb' conf node: <unknown error>
| mkimage Can't add hashes to FIT blob: -1
Signed-off-by: Ming Liu <liu.ming50@gmail.com>
Tested-by: Igor Opaniuk <igor.opaniuk@foundries.io>
I removed CONFIG_IS_BUILTIN and CONFIG_IS_MODULE in commit
7d78a4547d ("linux/kconfig.h: remove unused helper macros"), but
fixdep.c still looks for those. It's harmless, but also pointless and
possibly confusing to a future reader.
Fixes: 7d78a4547d ("linux/kconfig.h: remove unused helper macros")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
When "mkimage -l" was run on a block device it would fail with
erroneous message, because fstat reports a size of zero for those:
mkimage: Bad size: "/dev/sdb4" is not valid image
This patch identifies the "is a block device" case and reports it as
such, and if it knows how to determine the size of a block device on
the current OS, proceeds.
As shown in
http://www.mit.edu/afs.new/sipb/user/tytso/e2fsprogs/lib/blkid/getsize.c
this is no portable task, and I only handled the case of a modern
Linux kernel, which is what I can test.
Signed-off-by: Yann Dirson <yann@blade-group.com>
The ST-Ericsson DB8500 SoC contains a MUSB OTG controller which
supports both host and gadget mode. For some reason there is
nothing special about it - add a simple glue driver for Ux500
that literally just sets up MUSB together with a generic PHY.
There are no SoC-specific registers etc needed to make USB work.
The new Ux500 glue driver is only tested to work with DM_USB
and DM_USB_GADGET. Both host and gadget mode work fine on
the u8500 "stemmy" board that is already present in U-Boot.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.
The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.
Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The U-Boot "stemmy" board is mainly intended to simplify booting
mainline Linux on various smartphones from Samsung based on ST-Ericsson
Ux500. While the mainline kernel is working great, there are still some
features missing there. In particular, it is currently not possible to
charge the battery when using the mainline kernel.
This means that it is still necessary to boot the downstream/vendor
kernel from Samsung sometimes to charge the device. That kernel is
ancient, still uses board files + ATAGS instead of device trees and
relies on a strange very long kernel command line hardcoded in the
Samsung bootloader.
Actually, since mainline is booted with device trees there is a very
simple way to make the old downstream kernel work as well: We can
simply take most of the ATAGS passed to U-Boot from the Samsung
bootloader and copy them as-is when booting a kernel without device
tree. That way the long command line and other needed ATAGS are copied
as-is without having to bother with them.
The only exception is the ATAG_INITRD - since the initrd is loaded
by U-Boot, the atag for that should be generated in U-Boot so it points
to the correct address. All other ATAGS are copied as-is and not
generated in U-Boot.
Also use the chance and provide a serial# for U-Boot by parsing the
ATAG_SERIAL that is also passed by the Samsung bootloader.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At the moment the "stemmy" board attempts to detect the RAM size with
a simple memory test (get_ram_size()). Unfortunately, this does not work
correctly for devices with 768 MiB RAM (e.g. Samsung Galaxy Ace 2
(GT-I8160), "codina"). Reading/writing memory after the 768 MiB RAM
succeeds but actually overwrites some earlier parts of the memory.
For U-Boot this does not result in any major problems, but on Linux
this will eventually lead to strange crashes because of the memory
corruption.
Since the "stemmy" U-Boot port is designed to be chainloaded from
the original Samsung bootloader, the most reliable way to get the
available amount of RAM is to look at the ATAGS passed by the Samsung
bootloader. Fortunately, the header used to generate ATAGS in U-Boot
(asm/setup.h) can also be easily used to parse them.
Also clarify and simplify stemmy.h a bit to make it more clear where
some of the magic values in there are actually coming from.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/ )
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Add PCIe driver for UniPhier SoCs. This PCIe controller is based on
Synopsys DesignWare Core IP.
This version doesn't apply common DW functions because supported
controller doesn't have unroll version of iATU.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
I'm no longer work in Intel, change Intel SoCFPGA co-maintainer to
Tien Fong Chee.
Signed-off-by: Ley Foon Tan <lftan.linux@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
According to arch/arm/lib/crt0_64.S, the BSS section is "UNAVAILABLE"
and uninitialized before relocation. Also, it overlaps with the
appended DTB before relocation, so writing data into a variable
in the BSS section might corrupt the appended DTB.
Unfortunately, pinctrl-apq8016.c and pinctrl-apq8096.c do place the
"pin_name" variable in the BSS section (since it's uninitialized).
It's also used before relocation, when setting up the pinctrl for
the serial driver.
On DB410c this causes "GPIO_5" to be written into some part of an
appended DTB, e.g.:
80111820: edfe0dd0 9f100000 38000000 c00e0000 ...........8....
80111830: 28000000 11000000 10000000 00000000 ...(............
80111840: 4f495047 8800355f 00000000 00000000 GPIO_5..........
80111850: 00000000 00000000 01000000 00000000 ................
80111860: 03000000 04000000 00000000 02000000 ................
80111870: 03000000 04000000 0f000000 02000000 ................
80111880: 03000000 2d000000 1b000000 6c617551 .......-....Qual
80111890: 6d6d6f63 63655420 6c6f6e68 6569676f comm Technologie
Depending on the part of the DTB that is corrupted this might not
cause any problems, but it can also result in strange reboots
without any serial output.
Fortunately, in practice this does not cause issues on DB410c yet
because board_fdt_blob_setup() in dragonboard410c.c currently
overrides the appended DTB with the one passed by the previous
bootloader (LK) (which does not get corrupted).
DB820c does not have board_fdt_blob_setup() so I would expect it to
be affected by this problem. Perhaps everyone was just fortunate to
not compile an U-Boot configuration where the pin_name corrupts an
important part of the DTB.
Make sure "pin_name" is explicitly placed in the .data section
instead of .bss to fix this.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The sysinfo_get_str() implementation checks whether the sysinfo was even
detected. In U-Boot proper, sysinfo_detect() is not called anywhere but
on one specific board. Call sysinfo_detect() before sysinfo_get_str() to
make sure the sysinfo is detected and sysinfo_get_str() returns valid
value instead of -EPERM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace uclass_first_device_err(UCLASS_SYSINFO, &dev) with sysinfo_get(&dev).
The board_info code may use sysinfo to print board information, so use the
sysinfo functions consistently. The sysinfo_get() is internally implemented
as return uclass_first_device_err(UCLASS_SYSINFO, &dev) anyway, so there is
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Linux kernel binding is using atmel,24c01 compatible string. On the
other hand there is atmel,24c01a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simplify the code a bit by using dev_read_addr_ptr() instead of
dev_read_addr(). This avoids having to cast explicitly to the
struct nomadik_mtu_regs.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.
The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The original U-Boot port for the ST-Ericsson U8500 SoC was dropped
in commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch").
Most of the drivers related to the old port were removed, but the
db8500_gpio.c driver was forgotten for some reason. There is no way
to select it and it does not compile anymore because of missing
headers, so let's just remove it.
The new port for U8500 introduced in commit 689088f9da
("arm: Add support for ST-Ericsson U8500 SoC") fully embraces the
new Driver Model and device trees where possible, so this is
preparation to add a new, simplified GPIO driver based on DM_GPIO.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fix find_boot_device() to set bootdev_root if it finds the
bootdev from BootNext. Currently it sets the bootdev_root only
when it finds bootdev from BootOrder.
Fixes: c74cd8bd08 ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Accked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If multiple capsules are applied, the FMP drivers for the individual
capsules can expect the value of CapsuleLast to be accurate. Hence
CapsuleLast must be updated after each capsule.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Use log category LOGC_EFI. This allows to remove 'EFI:' prefixes in
messages.
* Rephrase some of the messages.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When reading a directory using EFI_FILE_PROTOCOL.Read() provide file
attributes and timestamps.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
