- Enable RTC for Intel Tangier
- Wrap the call to 8259 PIC with Kconfig options for old targets without
8259
- Warp the call to USB init with Kconfg options for coreboot & EFI
payload
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as an EFI payload. This was used to enable the
use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as a coreboot payload. This was used to enable
the use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
At present the Kconfig options (CONFIG_I8259_PIC and CONFIG_APIC)
do not include a prompt message, which makes it impossible to
be disabled from a board defconfig file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mask_irq(), unmask_irq() and specific_eoi() are provided by the
i8259 PIC driver and should be wrapped with CONFIG_I8259_PIC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
There are still systems running which do not have any LAPIC or even
IOAPIC. Responsible MSRs for those do not exist and the systems are
crashing on trying to setup LAPIC.
This commit makes the APIC stuff able to switch off for those boards
which dont' have an LAPIC / IOAPIC.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make the indentation aligned with what used elsewhere in U-Boot.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier SoC has RTC inside. So, enable it in ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The CRC16-CCITT checksum function is useful for space-constrained
applications (such as obtaining a checksum across a 2KBit or 4KBit
EEPROM) in boot applications. It has not been accessible from boot
scripts until now (due to not having a dedicated command and not being
supported by the hash infrstructure) limiting its applicability
outside of custom commands.
This adds the CRC16-CCITT (poly 0x1021, init 0x0) algorithm to the
list of available hashes and adds a new crc16_ccitt_wd_buf() to make
this possible.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Fix building crc16.o for SPL/TPL]
Signed-off-by: Tom Rini <trini@konsulko.com>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Similar to Clearfog rev 2.1, GPIO 19 also used to reset onboard ethernet
PHY.
This patch depend on
net: mvneta: Add GPIO configuration support
[URL: https://patchwork.ozlabs.org/patch/1007736/]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SPI flash support under U-Boot and SPL. The ENV size and offset,
ported from U-Boot 2013.01 Marvell version: 2015_T1.0p16
To create U-Boot image for SPI flash, user would need to replace
* CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC with CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
* CONFIG_ENV_IS_IN_MMC with CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove unused I2C support in SPL and use simple_malloc functions to
reduce SPL image size.
Since Helios4 does not have any PCIe allocated on SerDes, remove PCI
support. MTD layer on top of SPI flash is not needed, remove it also.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Make use of U-Boot's GPIO DM to control native GPIO and I2C IO expander.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable Marvell I2C driver and I2C IO expander. Set default bus to
external I2C bus. Define I2C aliases in device tree so it can be
recognized by the driver.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Store the environment before 1M into the block device.
This constant is easier to remember, saves a little space,
and is in line with what SolidRun's 2018.01-based fork does for the
clearfog.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
[ Aditya Prayoga:
* Port forward]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-By: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-By: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This syncs drivers/ddr/marvell/a38x/ with the mv_ddr-armada-18.09 branch
of https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
Specifically this syncs with commit 99d772547314 ("Bump mv_ddr to
release armada-18.09.2").
The complete log of changes is best obtained from the mv-ddr-marvell.git
repository but some relevant highlights are:
ddr3: add missing txsdll parameter
ddr3: fix tfaw timimg parameter
ddr3: fix trrd timimg parameter
merge ddr3 topology header file with mv_ddr_topology one
mv_ddr: a38x: fix zero memory size scrubbing issue
The upstream code is incorporated omitting the portions not relevant to
Armada-38x and DDR3. After that a semi-automated step is used to drop
unused features with unifdef
find drivers/ddr/marvell/a38x/ -name '*.[ch]' | \
xargs unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 \
-UCONFIG_APN806 -UCONFIG_MC_STATIC \
-UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_64BIT -UCONFIG_A3700 -UA3900 -UA80X0 \
-UA70X0
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dvG1
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20181207' of git://git.denx.de/u-boot-amlogic
Two fixes for the Amlogic Pinctrl driver :
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
Now that the Allwinner port in the official mainline ARM Trusted
Firmware repository has reached feature parity with the "legacy" ATF
port, let's use the opportunity to update the Allwinner 64-bit build
instructions. This changes:
- Update ATF build instructions to use the mainline repo.
- Add quick command lines for TL;DR people.
- Mention Allwinner H6 build target.
- Mention pre-built FEL binaries.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The lime2 features a too large capacitor on the LDO3 output, which
causes the PMIC to shutdown when enabling power. To be able to still
boot up however, we must gradually enable power on LDO3 for this board.
We do this by enabling both the inrush quirk and the maximum slope the
AXP209 supports.
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The lime2 features a too large capacitor on the LDO3 output, which
causes the PMIC to shutdown when enabling power. To be able to still
boot up however, we must gradually enable power on LDO3 for this board.
We do this by enabling both the inrush quirk and the maximum slope the
AXP209 supports.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some boards feature a capacitance on LDO3's output that is too large,
causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.
A fix appeared to be done with
commit 0e6e34ac8d ("sunxi: Olimex A20 boards: Enable LDO3 and LDO4 regulators").
The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system freezes.
While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.
To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 LDO3 regulator supports voltage rate control, or can set a
slew rate.
This allows for the power to gradually rise up to the desired voltage,
instead of spiking up as fast as possible. Reason to have this can be
to reduce the inrush currents for example.
There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.
In ideal world (where vendors follow the recommended design guidelines)
this setting should not be enabled by default. Unless of course AXP209
crashes instead of reporting overcurrent condition as it normally should
do in this case.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 has a few 'magisc-ish' values that are better served with
clear defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use a define for the chip version mask on the axp209.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use the standard BIT() macro for bitfield definitions in headers.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
When we clear a pmic_bus bit, we do a read-modify-write operation.
We waste some time however, by writing back the exact samea value
that was already set in the chip. Let us thus only do the write
in case data was changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently during init, we enable all power, then enable the dram and
after that check whether there was an error during power-up.
This makes little sense, we should enable power and then check if power
was brought up properly before we continue to initialize other things.
This patch moves the DRAM init after the power failure check.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
For a small SPL, it should be possible to build without SPI(-flash) drivers
or wihout MMC drivers.
For this to work, we have to change from 'select'ing options to 'imply'ing
them.
With this change, I can have SPL trimmed to my hard-wired starting method
(SPI-NOR or MMC) while still including all drivers in U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Enable DM_USB and DM_USB_DEV for AM57xx based boards.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is required when DM_USB is used, to bind the USB phys.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB clocks in late init stage to support ports under DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For USB ports that use the Driver Model, turn on the clocks during the
late init stage.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
syscon_regmap_lookup_by_phandle() can be used to get the regmap of a syscon
device from a reference in the DTS. It operates similarly to the linux
version of the namesake function.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
