There have been some refactoring of the DTS files for the Logic PD
DM37 Torpedo. This patch re-sync's the DTS files with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux. An addition include/dt-binding was
also brought with it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Several changes have been made to the AM3517-evm and the underlying
am3517.dtsi file. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USBOH module on imx25 chips contains two USB controllers which are
called USB OTG Controller and USB Host Controller. Each one has its EHCI
root hub. The OTG Controller's EHCI registers start at offset 0, the Host
Controller's registers start at offset 0x400.
We set CONFIG_MXC_USB_PORT=0 to select the OTG Controller and 1 for the
Host Controller. Therefore, IMX_USB_PORT_OFFSET must be 0x400. Using
this setting, the Host Controller starts working on my imx25 board.
Please note that the imx25 reference manual claims that the Host
Controller's registers start at 0x200. This is not correct. The Linux
Kernel uses the correct offset 0x400 in imx25.dtsi.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Not all i.MX6 pads use the same drive strength table. So far only the
240 Ohm to 34 Ohm table was available. Because the constants used have
speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when
according to the reference manual 52 Ohm is the correct value. This
patch adds the 260 Ohm to 37 Ohm table.
For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock)
uses the added table.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement MIGRATE_INFO_TYPE. This informs Linux that no migration
for the trusted operating system is necessary:
[ 0.000000] psci: Trusted OS migration not required
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
So far psci_cpu_(on|off) only worked for CPU1. Allow to control
CPU0 too. This allows to run the Linux PSCI checker successfully:
[ 2.213447] psci_checker: PSCI checker started using 2 CPUs
[ 2.219107] psci_checker: Starting hotplug tests
[ 2.223859] psci_checker: Trying to turn off and on again all CPUs
[ 2.267191] IRQ21 no longer affine to CPU0
[ 2.293266] Retrying again to check for CPU kill
[ 2.302269] CPU0 killed.
[ 2.311648] psci_checker: Trying to turn off and on again group 0 (CPUs 0-1)
[ 2.354354] IRQ21 no longer affine to CPU0
[ 2.383222] Retrying again to check for CPU kill
[ 2.392148] CPU0 killed.
[ 2.398063] psci_checker: Hotplug tests passed OK
[ 2.402910] psci_checker: Starting suspend tests (10 cycles per state)
[ 2.410019] psci_checker: cpuidle not available on CPU 0, ignoring
[ 2.416452] psci_checker: cpuidle not available on CPU 1, ignoring
[ 2.422757] psci_checker: Could not start suspend tests on any CPU
[ 2.429370] psci_checker: PSCI checker completed
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
PSCI 1.0 require PSCI_VERSION, PSCI_FEATURES, AFFINITY_INFO and
CPU_SUSPEND to be implemented. Commit 0ec3d98f76 ("mx7_common:
use psci 1.0 instead of 0.1") marked the i.MX 7 implementation to
be PSCI 1.0 compliant but failed to implement those functions.
Especially the missing PSCI version callback was noticeable when
booting Linux:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv65535.65535 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
This patch provides a minimal implementation thereof. With this
patch applied Linux detects PSCI 1.0:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
Fixes: 0ec3d98f76 ("mx7_common: use psci 1.0 instead of 0.1")
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
There is no need for assembly in the platform specific part of
the PSCI implementation.
Note that this does not make it a complete PSCI 1.0 implementation
yet but aids to do so in upcoming patches.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
A proper stack is required to safely use C code in psci_arch_cpu_entry.
Fixes: 486daaa618 ("arm: psci: add a weak function psci_arch_cpu_entry")
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
Tested-by: Patrick DELAUNAY <Patrick.delaunay@st.com>
This function can be used only for some of the nxp SoC. Make
it explicit in the comment. This adjust a bit commit
3aa4b703b4 ("imx: imx6: Move gpr_init() function to soc.c")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
lcdif_power_down should not be included in spl build to avoid build
failure introduced by commit eb111bb31d
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The GPMI NAND IP seems to be the same as used in i.MX 6Quad. Use
the fsl,imx6q-gpmi-nand compatible string like Linux devices trees
are.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This macro allows to detect whether the boot ROM initialized USB
already (serial downloader). This is helpful to reliably detect
if the system has been recovered via USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
On the veyron board the vcc33_sd regulator is used as vmmc-supply for
the SD card. This regulator is powered in the MMC core during power on
but its value is never actually set.
In the veyron platform the reset value for the LDO output is 1.8V while
the standard (min and max) value for this regulator defined in the DTS
is 3.3V. When the MMC core enable the regulator without setting its
value, the output is automatically set to 1.8V instead of 3.3V.
With this patch we preemptively set the value to 3.3V.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GRF_SOC_CON0.grf_force_jtag bit is automatically set at boot and it
is preventing the SDMMC to work correctly. Disable the JTAG function on
the assumption that a working SD has higher priority over JTAG.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use regulators_enable_boot_on() to init all the regulators with
regulator-boot-on property.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Without the patch SPL (in case of an error) creates an output like:
U-Boot SPL board initMissing DTB
The patch adds the missing line feed. So now we get:
U-Boot SPL board init
Missing DTB
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This implements the new 'spl_perform_fixups' hook for RK3399-based
boards and injects the /chosen/u-boot,spl-boot-device with an ofpath
corresponding to the boot device used.
The intended usage is for the full U-Boot stage to evaluate this in
scripts and then adapt its boot-order when using distro-boot.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
All other rockchip boards have rk_board_late_init() hook,
so add it to rk3188 boards also.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.5
(Linux commit 54fb3c180d05e9dfda892a93413514e99f0cbb19).
This will enable HDMI_5V for USB Amlogic Meson GXL P212 based boards.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This is needed for having access to the devices below this bus, most
important is uart and boot-device (spi, mmc, ...) in SPL stage.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Current implementation of find_next_zero_bit() is incompatible with arm64.
Hence fix it by using BITS_PER_LONG define instead of constants and
use generic ffz() implementation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
commit 4aba5fb857 ("arm: zynq: Rework FPGA initialization")
moved FPGA initialization from board_init() to arch_early_init_r(),
which is not called as part of the SPL
Fix this by calling arch_early_init_r() in the spl_board_init()
function, so the FPGA is correctly initialized
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
